USB GSM still in trouble after upgrade to 11.1-RELEASE-p10

[Per olof Ljungmark]

On 05/14/18 16:35, Willem Jan Withagen wrote:
> Hi,
> 
> Yesterday evening I upgraded a system to 11.1-RELEASE-p10.
> But that sort of upset my GSM-dongle I use for alarming.
> 
> And it did not do that before the upgrade, where I was running -p9.
> 
> 
> This is what I find repeated at rather high frequency in the logs:
> +ugen1.3: <HUAWEI Technologies HUAWEI Mobile> at usbus1
> +u3g0 on uhub3
> +u3g0: <Data Interface> on usbus1
> +u3g0: Found 2 ports.
> +umass0 on uhub3
> +umass0: <HUAWEI Technologies HUAWEI Mobile, class 0/0, rev 1.10/0.00,
> addr 3> on usbus1
> +umass0:  SCSI over Bulk-Only; quirks = 0x0000
> +umass0:3:0: Attached to scbus3
> +(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
> +(probe0:umass-sim0:0:0:0): CAM status: CCB request completed with an error
> +(probe0:umass-sim0:0:0:0): Retrying command
> +(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
> +(probe0:umass-sim0:0:0:0): CAM status: CCB request completed with an error
> +(probe0:umass-sim0:0:0:0): Retrying command
> +(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
> +(probe0:umass-sim0:0:0:0): CAM status: CCB request completed with an error
> +(probe0:umass-sim0:0:0:0): Retrying command
> +(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
> +(probe0:umass-sim0:0:0:0): CAM status: CCB request completed with an error
> +(probe0:umass-sim0:0:0:0): Retrying command
> +(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 00 00 00 24 00
> +(probe0:umass-sim0:0:0:0): CAM status: CCB request completed with an error
> +(probe0:umass-sim0:0:0:0): Error 5, Retries exhausted
> +ugen1.3: <HUAWEI Technologies HUAWEI Mobile> at usbus1 (disconnected)
> +u3g0: at uhub3, port 2, addr 3 (disconnected)
> +u3g0: detached
> +umass0: at uhub3, port 2, addr 3 (disconnected)
> +umass0: detached
> 
> So when I get home, I'm going to pull the stick.
> But what could be going on here?

I have identical behavior on a
FreeBSD 11.1-STABLE #0 r330526
system after it was restarted today.

It used to work with a Huawei E398 but after the reboot it does not,
just like your above.

Interestingly, I replaced it with a much older Huawei E1750 and that one
worked, but only after I rebooted again.

With the E398 after a reboot I only see /dev/cuau1, no cuaUX.X
If I pull it and replace with E1750 nothing happens
If I reboot with the E1750 in place, I get /dev/cuaUX.X

Fishy...