zfs resilver keeps restarting
Marc UBM Bocklet
ubm.freebsd at googlemail.com
Sun Sep 18 13:09:21 UTC 2016
Hi all,
due to two bad cables, I had two drives drop from my striped raidz2
pool (built on top of geli encrypted drives). I replaced one of the
drives before I realized that the cabling was at fault - that's the
drive which is being replaced in the ouput of zpool status below.
I have just installed the new cables and all sata errors are gone.
However, the resilver of the pool keeps restarting.
I see no errors in /var/log/messages, but zpool history -i says:
2016-09-18.14:56:21 [txg:1219501] scan setup func=2 mintxg=3
maxtxg=1219391 2016-09-18.14:56:51 [txg:1219505] scan done complete=0
2016-09-18.14:56:51 [txg:1219505] scan setup func=2 mintxg=3
maxtxg=1219391 2016-09-18.14:57:20 [txg:1219509] scan done complete=0
2016-09-18.14:57:20 [txg:1219509] scan setup func=2 mintxg=3
maxtxg=1219391 2016-09-18.14:57:49 [txg:1219513] scan done complete=0
2016-09-18.14:57:49 [txg:1219513] scan setup func=2 mintxg=3
maxtxg=1219391 2016-09-18.14:58:19 [txg:1219517] scan done complete=0
2016-09-18.14:58:19 [txg:1219517] scan setup func=2 mintxg=3
maxtxg=1219391 2016-09-18.14:58:45 [txg:1219521] scan done complete=0
2016-09-18.14:58:45 [txg:1219521] scan setup func=2 mintxg=3
maxtxg=1219391
I assume that "scan done complete=0" means that the resilver didn't
finish?
pool layout is the following:
pool: pool
state: DEGRADED
status: One or more devices is currently being resilvered. The pool
will continue to function, possibly in a degraded state.
action: Wait for the resilver to complete.
scan: resilver in progress since Sun Sep 18 14:51:39 2016
235G scanned out of 9.81T at 830M/s, 3h21m to go
13.2M resilvered, 2.34% done
config:
NAME STATE READ WRITE CKSUM
pool DEGRADED 0 0 0
raidz2-0 ONLINE 0 0 0
da6.eli ONLINE 0 0 0
da7.eli ONLINE 0 0 0
ada1.eli ONLINE 0 0 0
ada2.eli ONLINE 0 0 0
da10.eli ONLINE 0 0 2
da11.eli ONLINE 0 0 0
da12.eli ONLINE 0 0 0
da13.eli ONLINE 0 0 0
raidz2-1 DEGRADED 0 0 0
da0.eli ONLINE 0 0 0
da1.eli ONLINE 0 0 0
da2.eli ONLINE 0 0 1
(resilvering)
replacing-3 DEGRADED 0 0 1
10699825708166646100 UNAVAIL 0 0 0
was /dev/da3.eli da4.eli ONLINE 0 0 0
(resilvering)
da3.eli ONLINE 0 0 0
da5.eli ONLINE 0 0 0
da8.eli ONLINE 0 0 0
da9.eli ONLINE 0 0 0
errors: No known data errors
system is
FreeBSD xxx 10.1-BETA1 FreeBSD 10.1-BETA1 #27 r271633:
Mon Sep 15 22:34:05 CEST 2014
root at xxx:/usr/obj/usr/src/sys/xxx amd64
controller is
SAS2116 PCI-Express Fusion-MPT SAS-2 [Meteor]
Drives are connected via four four-port sata cables.
Should I upgrade to 10.3-release or did I make some sort of
configuration error / overlook something?
Thanks in advance!
Cheers,
Marc
More information about the freebsd-stable
mailing list