FreeBSD 5.3 on Digital Personal Workstation 500au
Wilko Bulte
wb at freebie.xs4all.nl
Wed May 4 14:09:42 PDT 2005
Sounds similar (IIRC) to the problem reported for the PWS and
5.4-RC
No resolution that I have seen though :-(
W/
On Wed, May 04, 2005 at 04:57:13PM -0400, benash at eecs.umich.edu wrote..
>
>
> Hi,
>
> I am trying to install FreeBSD 5.3 onto a Digital Personal Workstation 500au.
> However, when booting from the CD (or floppies), the CPU halts and attempts to
> boot again. The output of this loop is shown below, along with some
> configuration info below that. I have tried moving the SCSI card from the
> 32-bit slot to a 64-bit slot, and I also tried removing the other two PCI
> devices (a NIC and a graphics card). Neither action made any difference.
>
> All the firmware has just been updated to the latest version. Also, I am able
> to install version 4.11 from CD without any problem.
>
> I would really apreciate any hints or ideas that people have on this.
>
> *** keyboard not plugged in ...
>
> ff.fe.fd.fc.fb.fa.f9.f8.f7.f6.f5.CPU 0 speed is 2.00 ns (500MHz)
>
> Digital Personal WorkStation 500au5.e4.
> Console V7.2-1 Mar 6 2000 14:47:02
>
> CPU 0 booting
>
> >>>^C
> >>>b dka0
> (boot dka0.0.0.4.0 -flags a)
> block 0 of dka0.0.0.4.0 is a valid boot block
> reading 410 blocks from dka0.0.0.4.0
> bootstrap code read in
> base = 1d8000, image_start = 0, image_bytes = 33400
> initializing HWRPB at 2000
> initializing page table at 1ca000
> initializing machine state
> setting affinity to the primary CPU
> jumping to bootstrap code
> Console: SRM firmware console
> VMS PAL rev: 0x1000000010114
> OSF PAL rev: 0x1000000020116
> Switch to OSF PAL code succeeded.
>
> FreeBSD/alpha SRM CD9660 boot, Revision 1.2
> (root at ds10.wbnet, Fri Nov 5 04:07:45 UTC 2004)
> Memory: 655360 k
> Loading /boot/defaults/loader.conf
> /boot/kernel/kernel data=0x5c4ce0+0x3d990 syms=[0x8+0x64ab8+0x8+0x53436]
> |
> Hit [Enter] to boot immediately, or any other key for command prompt.
> Booting [/boot/kernel/kernel]...
> Entering /boot/kernel/kernel at 0xfffffc0000344c30...
> Copyright (c) 1992-2004 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 5.3-RELEASE #0: Fri Nov 5 11:30:09 UTC 2004
> root at ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
> Digital Personal Workstation (Miata)
> Digital Personal WorkStation 500au, 500MHz
> 8192 byte page size, 1 processor.
> CPU: EV56 (21164A) major=7 minor=0 extensions=0x1<BWX>
> OSF PAL rev: 0x1000000020116
> real memory = 669147136 (638 MB)
> avail memory = 641531904 (611 MB)
> cia0: <2117x Core Logic chipset>
> cia0: Pyxis, pass 1
> cia0: extended capabilities: 1<BWEN>
> cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
> pcib0: <2117x PCI host bus adapter> on cia0
> pci0: <PCI bus> on pcib0
> dc0: <Intel 21143 10/100BaseTX> port 0x9000-0x907f mem 0x80140000-0x8014007f irq
> 0 at device 3.0 on pci0
> miibus0: <MII bus> on dc0
> nsphy0: <DP83840 10/100 media interface> on miibus0
> nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> dc0: Ethernet address: 00:00:f8:75:af:31
> dc0: if_start running deferred for Giant
> dc0: interrupting at CIA irq 0
> dc0: [GIANT-LOCKED]
> atapci0: <CMD 646 WDMA2 controller> port
> 0x9080-0x908f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 1 at device 4.0 on pci0
> atapci0: interrupting at CIA irq 1
> ata0: channel #0 on atapci0
> ata0: interrupting at ISA irq 14
> ata1: channel #1 on atapci0
> ata1: interrupting at ISA irq 15
> isab0: <PCI-ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> pcib1: <PCI-PCI bridge> at device 20.0 on pci0
> pci1: <PCI bus> on pcib1
> pci1: <display> at device 8.0 (no driver attached)
> isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x8000-0x80ff mem
> 0x80070000-0x80070fff irq 16 at device 9.0 on pci1
> isp0: interrupting at CIA irq 16
> isp0: [GIANT-LOCKED]
> xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x8100-0x817f mem
> 0x80071000-0x8007107f irq 20 at device 10.0 on pci1
> miibus1: <MII bus> on xl0
> xlphy0: <3Com internal media interface> on miibus1
> xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> xl0: Ethernet address: 00:10:4b:95:ab:ac
> xl0: interrupting at CIA irq 20
>
> halted CPU 0
>
> halt code = 5
> HALT instruction executed
> PC = 1f00
>
> CPU 0 booting
>
> (boot dka0.0.0.4.0 -flags a)
> block 0 of dka0.0.0.4.0 is a valid boot block
> reading 410 blocks from dka0.0.0.4.0
> bootstrap code read in
> base = 1d8000, image_start = 0, image_bytes = 33400
> initializing HWRPB at 2000
> initializing page table at 1ca000
> initializing machine state
> setting affinity to the primary CPU
> jumping to bootstrap code
> Console: SRM firmware console
> VMS PAL rev: 0x1000000010114
> OSF PAL rev: 0x1000000020116
> Switch to OSF PAL code succeeded.
>
> FreeBSD/alpha SRM CD9660 boot, Revision 1.2
> (root at ds10.wbnet, Fri Nov 5 04:07:45 UTC 2004)
> Memory: 655360 k
> Loading /boot/defaults/loader.conf
> /boot/kernel/kernel data=0x5c4ce0+0x3d990 syms=[0x8+0x64ab8+0x8+0x53436]
> |
> Hit [Enter] to boot immediately, or any other key for command prompt.
> Booting [/boot/kernel/kernel]...
> Entering /boot/kernel/kernel at 0xfffffc0000344c30...
> Copyright (c) 1992-2004 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 5.3-RELEASE #0: Fri Nov 5 11:30:09 UTC 2004
> root at ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
>
> /* THIS PROCESS REPEATS FOREVER . . . */
>
> >>>show dev
> dka0.0.0.4.0 DKA0 TOSHIBA CD-ROM XM-6102B 1106
> dkc0.0.0.1009.0 DKC0 QUANTUM ATLAS10K2-TY184L DA40
> dva0.0.0.0.1 DVA0
> ewa0.0.0.3.0 EWA0 00-00-F8-75-AF-31
> pkc0.7.0.1009.0 PKC0 SCSI Bus ID 7 5.57
> pqa0.0.0.4.0 PQA0 PCI EIDE
> pqb0.0.1.4.0 PQB0 PCI EIDE
> >>>show conf
>
> Firmware
> SRM Console: V7.2-1 Mar 6 2000 14:47:02
> ARC Console: 5.70
> PALcode: OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode V1.22-18
> SROM Version: v5.90
>
> Processor
> DECchip (tm) 21164A-2 Pass 500 MHz 96 KBytes SCache
> 2 MB BCache
> PYXIS ASIC Pass 257
>
> MEMORY
>
>
> Memory Size = 640Mb
>
> Bank Size/Sets Base Addr
> ------ ---------- ---------
> 0 512Mb 00000000
> 1 64Mb 20000000
> 2 64Mb 24000000
>
>
> BCache Size = 2Mb
>
> Tested Memory = 640Mbytes
>
> PCI Bus
> Bus 00 Slot 03: Digital Semiconductor 21143 Network Controller
> ewa0.0.0.3.0 00-00-F8-75-AF-31
>
> Bus 00 Slot 04: PCI IDE
> pqa0.0.0.4.0 PCI EIDE
> dka0.0.0.4.0 TOSHIBA CD-ROM XM-61
>
> Bus 00 Slot 07: Intel SIO 82378
>
>
> Bus 00 Slot 20: DECchip 21052 PCI to PCI Bridge
> Bus 01 Slot 08: Digital ZLXp Graphics Controller
> Bus 01 Slot 09: ISP1040 Scsi Controller
> pkc0.7.0.1009.0 SCSI Bus ID 7
> dkc0.0.0.1009.0 QUANTUM ATLAS10K2-TY
>
> Bus 01 Slot 10: Vendor: 10b7 Device: 9055 Sub_id: 905510b7
> ISA
> Slot Device Name Type Enabled BaseAddr IRQ DMA
> 0
> 0 MOUSE Embedded Yes 60 12
> 1 KBD Embedded Yes 60 1
> 2 COM1 Embedded Yes 3f8 4
> 3 COM2 Embedded Yes 2f8 3
> 4 LPT1 Embedded Yes 3bc 7
> 5 FLOPPY Embedded Yes 3f0 6 2
> 6 EIDE Embedded Yes 1f0 14
> 3f6 15
> 170
> 376
> 7 ES1888 Embedded Yes 220 5 1
> >>>show
> adv_diag off
> auto_action BOOT
> boot_dev dka0.0.0.4.0
> boot_file
> boot_osflags a
> boot_reset OFF
> bootdef_dev dkc0.0.0.1009.0
> booted_dev dka0.0.0.4.0
> booted_file
> booted_osflags a
> char_set 0
> console graphics
> controlp on
> d_bell off
> d_cleanup on
> d_complete off
> d_eop off
> d_group field
> d_harderr halt
> d_loghard on
> d_logsoft off
> d_oper off
> d_passes 1
> d_quick off
> d_report full
> d_runtime 0
> d_softerr continue
> d_startup off
> d_status off
> d_trace off
> dma_prefetch ON
> dump_dev
> enable_audit ON
> ewa0_arp_tries 3
> ewa0_bootp_file
> ewa0_bootp_server
> ewa0_bootp_tries 3
> ewa0_def_ginetaddr 0.0.0.0
> ewa0_def_inetaddr 0.0.0.0
> ewa0_def_inetfile
> ewa0_def_sinetaddr 0.0.0.0
> ewa0_def_subnetmask 0.0.0.0
> ewa0_ginetaddr 0.0.0.0
> ewa0_inet_init bootp
> ewa0_inetaddr 0.0.0.0
> ewa0_inetfile
> ewa0_loop_count 3e8
> ewa0_loop_inc a
> ewa0_loop_patt ffffffff
> ewa0_loop_size 2e
> ewa0_lp_msg_node 1
> ewa0_mode Twisted-Pair
> ewa0_protocols BOOTP
> ewa0_sinetaddr 0.0.0.0
> ewa0_tftp_tries 3
> ffauto OFF
> ffnext OFF
> graphics_page 0
> graphics_type VIDEO
> kbd_hardware_type PCXAL
> language 36
> language_name English(American)
> license MU
> mop_debug OFF
> mop_password 00-00000000-00000000
> mop_version 1
> mopv3_boot OFF
> os_type UNIX
> pal OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode V1.22-18
> pci_device_override 0
> pci_parity off
> pkc0_host_id 7
> pkc0_mode ultra
> pkc0_soft_term diff
> quick_start OFF
> scsi_poll ON
> srm2ctrl
> srm2dev
> sys_serial_num
> tt_allow_login 1
> tta0_page 0
> tta0_type VIDEO
> tty_dev 0
> version V7.2-1 Mar 6 2000 14:47:02
> >>>
>
>
>
> Thanks for looking at this.
>
> Ben Nash
> benash at eecs.umich.edu
>
>
>
> _______________________________________________
> freebsd-alpha at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-alpha
> To unsubscribe, send any mail to "freebsd-alpha-unsubscribe at freebsd.org"
--- end of quoted text ---
--
Wilko Bulte wilko at FreeBSD.org
More information about the freebsd-alpha
mailing list