FreeBSD 5.3 on Digital Personal Workstation 500au
benash at eecs.umich.edu
benash at eecs.umich.edu
Wed May 4 19:09:07 PDT 2005
OK, it looks like I fixed the problem. I needed to have the SCSI card in a
64-bit slot WHILE the other two cards were removed (so that nothing was plugged
into a 32-bit slot). The 5.3 installation seemed to complete without trouble,
and I am able to login as root.
Any ideas as to why this fixed things?
Ben Nash
benash at eecs.umich.edu
Quoting Wilko Bulte <wb at freebie.xs4all.nl>:
> Sounds similar (IIRC) to the problem reported for the PWS and
> 5.4-RC
>
> No resolution that I have seen though :-(
>
> W/
>
>
> On Wed, May 04, 2005 at 04:57:13PM -0400, benash at eecs.umich.edu wrote..
> >
> >
> > Hi,
> >
> > I am trying to install FreeBSD 5.3 onto a Digital Personal Workstation
> 500au.
> > However, when booting from the CD (or floppies), the CPU halts and attempts
> to
> > boot again. The output of this loop is shown below, along with some
> > configuration info below that. I have tried moving the SCSI card from the
> > 32-bit slot to a 64-bit slot, and I also tried removing the other two PCI
> > devices (a NIC and a graphics card). Neither action made any difference.
> >
> > All the firmware has just been updated to the latest version. Also, I am
> able
> > to install version 4.11 from CD without any problem.
> >
> > I would really apreciate any hints or ideas that people have on this.
> >
> > *** keyboard not plugged in ...
> >
> > ff.fe.fd.fc.fb.fa.f9.f8.f7.f6.f5.CPU 0 speed is 2.00 ns (500MHz)
> >
> > Digital Personal WorkStation 500au5.e4.
> > Console V7.2-1 Mar 6 2000 14:47:02
> >
> > CPU 0 booting
> >
> > >>>^C
> > >>>b dka0
> > (boot dka0.0.0.4.0 -flags a)
> > block 0 of dka0.0.0.4.0 is a valid boot block
> > reading 410 blocks from dka0.0.0.4.0
> > bootstrap code read in
> > base = 1d8000, image_start = 0, image_bytes = 33400
> > initializing HWRPB at 2000
> > initializing page table at 1ca000
> > initializing machine state
> > setting affinity to the primary CPU
> > jumping to bootstrap code
> > Console: SRM firmware console
> > VMS PAL rev: 0x1000000010114
> > OSF PAL rev: 0x1000000020116
> > Switch to OSF PAL code succeeded.
> >
> > FreeBSD/alpha SRM CD9660 boot, Revision 1.2
> > (root at ds10.wbnet, Fri Nov 5 04:07:45 UTC 2004)
> > Memory: 655360 k
> > Loading /boot/defaults/loader.conf
> > /boot/kernel/kernel data=0x5c4ce0+0x3d990 syms=[0x8+0x64ab8+0x8+0x53436]
> > |
> > Hit [Enter] to boot immediately, or any other key for command prompt.
> > Booting [/boot/kernel/kernel]...
> > Entering /boot/kernel/kernel at 0xfffffc0000344c30...
> > Copyright (c) 1992-2004 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> > The Regents of the University of California. All rights reserved.
> > FreeBSD 5.3-RELEASE #0: Fri Nov 5 11:30:09 UTC 2004
> > root at ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
> > Digital Personal Workstation (Miata)
> > Digital Personal WorkStation 500au, 500MHz
> > 8192 byte page size, 1 processor.
> > CPU: EV56 (21164A) major=7 minor=0 extensions=0x1<BWX>
> > OSF PAL rev: 0x1000000020116
> > real memory = 669147136 (638 MB)
> > avail memory = 641531904 (611 MB)
> > cia0: <2117x Core Logic chipset>
> > cia0: Pyxis, pass 1
> > cia0: extended capabilities: 1<BWEN>
> > cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
> > pcib0: <2117x PCI host bus adapter> on cia0
> > pci0: <PCI bus> on pcib0
> > dc0: <Intel 21143 10/100BaseTX> port 0x9000-0x907f mem
> 0x80140000-0x8014007f irq
> > 0 at device 3.0 on pci0
> > miibus0: <MII bus> on dc0
> > nsphy0: <DP83840 10/100 media interface> on miibus0
> > nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > dc0: Ethernet address: 00:00:f8:75:af:31
> > dc0: if_start running deferred for Giant
> > dc0: interrupting at CIA irq 0
> > dc0: [GIANT-LOCKED]
> > atapci0: <CMD 646 WDMA2 controller> port
> > 0x9080-0x908f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 1 at device 4.0 on
> pci0
> > atapci0: interrupting at CIA irq 1
> > ata0: channel #0 on atapci0
> > ata0: interrupting at ISA irq 14
> > ata1: channel #1 on atapci0
> > ata1: interrupting at ISA irq 15
> > isab0: <PCI-ISA bridge> at device 7.0 on pci0
> > isa0: <ISA bus> on isab0
> > pcib1: <PCI-PCI bridge> at device 20.0 on pci0
> > pci1: <PCI bus> on pcib1
> > pci1: <display> at device 8.0 (no driver attached)
> > isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x8000-0x80ff mem
> > 0x80070000-0x80070fff irq 16 at device 9.0 on pci1
> > isp0: interrupting at CIA irq 16
> > isp0: [GIANT-LOCKED]
> > xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x8100-0x817f mem
> > 0x80071000-0x8007107f irq 20 at device 10.0 on pci1
> > miibus1: <MII bus> on xl0
> > xlphy0: <3Com internal media interface> on miibus1
> > xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > xl0: Ethernet address: 00:10:4b:95:ab:ac
> > xl0: interrupting at CIA irq 20
> >
> > halted CPU 0
> >
> > halt code = 5
> > HALT instruction executed
> > PC = 1f00
> >
> > CPU 0 booting
> >
> > (boot dka0.0.0.4.0 -flags a)
> > block 0 of dka0.0.0.4.0 is a valid boot block
> > reading 410 blocks from dka0.0.0.4.0
> > bootstrap code read in
> > base = 1d8000, image_start = 0, image_bytes = 33400
> > initializing HWRPB at 2000
> > initializing page table at 1ca000
> > initializing machine state
> > setting affinity to the primary CPU
> > jumping to bootstrap code
> > Console: SRM firmware console
> > VMS PAL rev: 0x1000000010114
> > OSF PAL rev: 0x1000000020116
> > Switch to OSF PAL code succeeded.
> >
> > FreeBSD/alpha SRM CD9660 boot, Revision 1.2
> > (root at ds10.wbnet, Fri Nov 5 04:07:45 UTC 2004)
> > Memory: 655360 k
> > Loading /boot/defaults/loader.conf
> > /boot/kernel/kernel data=0x5c4ce0+0x3d990 syms=[0x8+0x64ab8+0x8+0x53436]
> > |
> > Hit [Enter] to boot immediately, or any other key for command prompt.
> > Booting [/boot/kernel/kernel]...
> > Entering /boot/kernel/kernel at 0xfffffc0000344c30...
> > Copyright (c) 1992-2004 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> > The Regents of the University of California. All rights reserved.
> > FreeBSD 5.3-RELEASE #0: Fri Nov 5 11:30:09 UTC 2004
> > root at ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
> >
> > /* THIS PROCESS REPEATS FOREVER . . . */
> >
> > >>>show dev
> > dka0.0.0.4.0 DKA0 TOSHIBA CD-ROM XM-6102B 1106
> > dkc0.0.0.1009.0 DKC0 QUANTUM ATLAS10K2-TY184L DA40
> > dva0.0.0.0.1 DVA0
> > ewa0.0.0.3.0 EWA0 00-00-F8-75-AF-31
> > pkc0.7.0.1009.0 PKC0 SCSI Bus ID 7 5.57
> > pqa0.0.0.4.0 PQA0 PCI EIDE
> > pqb0.0.1.4.0 PQB0 PCI EIDE
> > >>>show conf
> >
> > Firmware
> > SRM Console: V7.2-1 Mar 6 2000 14:47:02
> > ARC Console: 5.70
> > PALcode: OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode V1.22-18
> > SROM Version: v5.90
> >
> > Processor
> > DECchip (tm) 21164A-2 Pass 500 MHz 96 KBytes SCache
> > 2 MB BCache
> > PYXIS ASIC Pass 257
> >
> > MEMORY
> >
> >
> > Memory Size = 640Mb
> >
> > Bank Size/Sets Base Addr
> > ------ ---------- ---------
> > 0 512Mb 00000000
> > 1 64Mb 20000000
> > 2 64Mb 24000000
> >
> >
> > BCache Size = 2Mb
> >
> > Tested Memory = 640Mbytes
> >
> > PCI Bus
> > Bus 00 Slot 03: Digital Semiconductor 21143 Network Controller
> > ewa0.0.0.3.0 00-00-F8-75-AF-31
> >
> > Bus 00 Slot 04: PCI IDE
> > pqa0.0.0.4.0 PCI EIDE
> > dka0.0.0.4.0 TOSHIBA CD-ROM
> XM-61
> >
> > Bus 00 Slot 07: Intel SIO 82378
> >
> >
> > Bus 00 Slot 20: DECchip 21052 PCI to PCI Bridge
> > Bus 01 Slot 08: Digital ZLXp Graphics Controller
> > Bus 01 Slot 09: ISP1040 Scsi Controller
> > pkc0.7.0.1009.0 SCSI Bus ID 7
> > dkc0.0.0.1009.0 QUANTUM
> ATLAS10K2-TY
> >
> > Bus 01 Slot 10: Vendor: 10b7 Device: 9055 Sub_id: 905510b7
> > ISA
> > Slot Device Name Type Enabled BaseAddr IRQ DMA
> > 0
> > 0 MOUSE Embedded Yes 60 12
> > 1 KBD Embedded Yes 60 1
> > 2 COM1 Embedded Yes 3f8 4
> > 3 COM2 Embedded Yes 2f8 3
> > 4 LPT1 Embedded Yes 3bc 7
> > 5 FLOPPY Embedded Yes 3f0 6 2
> > 6 EIDE Embedded Yes 1f0 14
> > 3f6 15
> > 170
> > 376
> > 7 ES1888 Embedded Yes 220 5 1
> > >>>show
> > adv_diag off
> > auto_action BOOT
> > boot_dev dka0.0.0.4.0
> > boot_file
> > boot_osflags a
> > boot_reset OFF
> > bootdef_dev dkc0.0.0.1009.0
> > booted_dev dka0.0.0.4.0
> > booted_file
> > booted_osflags a
> > char_set 0
> > console graphics
> > controlp on
> > d_bell off
> > d_cleanup on
> > d_complete off
> > d_eop off
> > d_group field
> > d_harderr halt
> > d_loghard on
> > d_logsoft off
> > d_oper off
> > d_passes 1
> > d_quick off
> > d_report full
> > d_runtime 0
> > d_softerr continue
> > d_startup off
> > d_status off
> > d_trace off
> > dma_prefetch ON
> > dump_dev
> > enable_audit ON
> > ewa0_arp_tries 3
> > ewa0_bootp_file
> > ewa0_bootp_server
> > ewa0_bootp_tries 3
> > ewa0_def_ginetaddr 0.0.0.0
> > ewa0_def_inetaddr 0.0.0.0
> > ewa0_def_inetfile
> > ewa0_def_sinetaddr 0.0.0.0
> > ewa0_def_subnetmask 0.0.0.0
> > ewa0_ginetaddr 0.0.0.0
> > ewa0_inet_init bootp
> > ewa0_inetaddr 0.0.0.0
> > ewa0_inetfile
> > ewa0_loop_count 3e8
> > ewa0_loop_inc a
> > ewa0_loop_patt ffffffff
> > ewa0_loop_size 2e
> > ewa0_lp_msg_node 1
> > ewa0_mode Twisted-Pair
> > ewa0_protocols BOOTP
> > ewa0_sinetaddr 0.0.0.0
> > ewa0_tftp_tries 3
> > ffauto OFF
> > ffnext OFF
> > graphics_page 0
> > graphics_type VIDEO
> > kbd_hardware_type PCXAL
> > language 36
> > language_name English(American)
> > license MU
> > mop_debug OFF
> > mop_password 00-00000000-00000000
> > mop_version 1
> > mopv3_boot OFF
> > os_type UNIX
> > pal OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode
> V1.22-18
> > pci_device_override 0
> > pci_parity off
> > pkc0_host_id 7
> > pkc0_mode ultra
> > pkc0_soft_term diff
> > quick_start OFF
> > scsi_poll ON
> > srm2ctrl
> > srm2dev
> > sys_serial_num
> > tt_allow_login 1
> > tta0_page 0
> > tta0_type VIDEO
> > tty_dev 0
> > version V7.2-1 Mar 6 2000 14:47:02
> > >>>
> >
> >
> >
> > Thanks for looking at this.
> >
> > Ben Nash
> > benash at eecs.umich.edu
> >
> >
> >
> > _______________________________________________
> > freebsd-alpha at freebsd.org mailing list
> > http://lists.freebsd.org/mailman/listinfo/freebsd-alpha
> > To unsubscribe, send any mail to "freebsd-alpha-unsubscribe at freebsd.org"
> --- end of quoted text ---
>
> --
> Wilko Bulte wilko at FreeBSD.org
>
More information about the freebsd-alpha
mailing list