Linux 2.0.34 and aic7xxx v5.0.1[49] driver

[Stephane Bortzmeyer]

On Sunday 28 June 1998, at 10 h 37, the keyboard of Stephane Bortzmeyer 
<stephane at sources.org> wrote:


> > I'm having problems with the new aic7xxx driver as shipped with 
> > Linux kernel version 2.0.34.  As others have reported on this 

BTW, the problem is the same with Linux 2.0.35pre5.

When the box succeed in booting, the two CD drives are not detected.

dmesg :

aic7xxx: Warning - detected auto-termination on controller:
aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 11/0
aic7xxx: Please verify driver detected settings are correct.
aic7xxx: If not, then please properly set the device termination
aic7xxx: in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
aic7xxx: during machine bootup.
aic7xxx: Cables present (Int-50 YES, Int-68 YES, Ext-68 NO)
aic7xxx: Termination (Low OFF, High ON)
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 11/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) BIOS enabled, IO Port 0xe800, IRQ 11
(scsi0) IO Memory at 0xfafff000, MMAP Memory at 0x4805000
(scsi0) Downloading sequencer code... 406 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.19/3.2.4
       <Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:-1:-1) Scanning channel for devices.
  Vendor: WDIGTL    Model: WDE4360-1807A3    Rev: 1.80
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:0:0) Using wide (16 bit) transfers.
(scsi0:0:0:0) Synchronous at 10.0MHz, offset 8.
  Vendor: WDIGTL    Model: WDE4360-1807A3    Rev: 1.80
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi0:0:1:0) Using wide (16 bit) transfers.
(scsi0:0:1:0) Synchronous at 10.0MHz, offset 8.
scsi : detected 2 SCSI disks total.



/proc/scsi/aic7xxx/0 :

Adaptec AIC7xxx driver version: 5.0.19/3.2.4
Compile Options:
  AIC7XXX_RESET_DELAY    : 15
  AIC7XXX_TAGGED_QUEUEING: Adapter Support Enabled
                             Check below to see which
                             devices use tagged queueing
  AIC7XXX_PAGE_ENABLE    : Enabled (This is no longer an option)
  AIC7XXX_PROC_STATS     : Enabled

Adapter Configuration:
           SCSI Adapter: Adaptec AHA-294X Ultra SCSI host adapter
                           Wide Controller
    PCI MMAPed I/O Base: 0xfafff000
      Adaptec SCSI BIOS: Enabled
                    IRQ: 11
                   SCBs: Active 0, Max Active 2,
                         Allocated 30, HW 16, Page 255
             Interrupts: 6162
      BIOS Control Word: 0x18b6
   Adapter Control Word: 0x0019
   Extended Translation: Enabled
Disconnect Enable Flags: 0xffff
 Tag Queue Enable Flags: 0x0000
Ordered Queue Tag Flags: 0x0000
Default Tag Queue Depth: 8
    Tagged Queue By Device array for aic7xxx host instance 0:
      {255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255}
    Actual queue depth per device for aic7xxx host instance 0:
      {1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}





To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message