Apparent fxp regression in FreeBSD 8.4-RC3

Jeremy Chadwick jdc at koitsu.org
Sun May 12 03:23:05 UTC 2013


On Sat, May 11, 2013 at 10:57:44PM -0400, Michael L. Squires wrote:
> I upgraded to FreeBSD 8.4-RC3 and noticed a problem with the fxp
> driver on an older Supermicro single CPU single core Xeon
> motherboard.
> 
> I know that 8.3-Release does not have this issue, but don't know when in
> the updates to that release the regression was introduced.
> 
> I use the fxp driver to connect to a Motorola Surfboard cable modem,
> and immediately saw the following occur many times:
> 
> May 10 23:00:04 familysquires kernel: fxp0: link state changed to DOWN
> May 10 23:00:04 familysquires dhclient: New Subnet Mask (fxp0):
> 255.255.240.0
> May 10 23:00:04 familysquires dhclient: New Broadcast Address
> (fxp0): 255.255.25
> 5.255
> May 10 23:00:04 familysquires dhclient: New Routers (fxp0): xx.xxx.xxx.1
> May 10 23:00:06 familysquires kernel: fxp0: link state changed to UP
> May 10 23:00:22 familysquires dhclient: New IP Address (fxp0):
> xx.xxx.xxx.163
> May 10 23:00:22 familysquires kernel: fxp0: link state changed to DOWN
> May 10 23:00:22 familysquires dhclient: New Subnet Mask (fxp0):
> 255.255.240.0
> May 10 23:00:22 familysquires dhclient: New Broadcast Address
> (fxp0): 255.255.255.255
> May 10 23:00:22 familysquires dhclient: New Routers (fxp0): xx.xxx.xxx.1
> May 10 23:00:24 familysquires kernel: fxp0: link state changed to UP
> 
> repeated without end.
> 
> I reinsalled 8.3-Release p8
> 
> FreeBSD familysquires.net 8.3-RELEASE-p8 FreeBSD 8.3-RELEASE-p8 #46:
> Sat May 11 00:05:26 EDT 2013
> 
> which ended the string up fxp up/down messages.  This kernel has now
> operated for 24 hours without generating this error.
> 
> I've attached a verbose dmesg from 8.4-RC3 and a standard dmesg from
> 8.3-Release p8, and can provide whatever else you need.
> 
> This is not a critical issue for me.  The system has an unused bge interface
> (replaced by an Intel em0 interface during a previous bout of a problem with
> the bge driver).
> 
> Mike Squires
> mikes at siralan.org

> Copyright (c) 1992-2013 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 8.4-PRERELEASE #45: Fri May 10 09:43:40 EDT 2013
>     root at familysquires.net:/usr/obj/usr/src/sys/NEWGATE i386
> gcc version 4.2.1 20070831 patched [FreeBSD]
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc1060000.
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Calibrating TSC clock ... TSC clock: 2666786988 Hz
> CPU: Intel(R) Xeon(TM) CPU 2.66GHz (2666.79-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0xf25  Family = f  Model = 2  Stepping = 5
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0x4400<CNXT-ID,xTPR>
> 
> Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 128 entries
> Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
> 1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64 byte line size
> Trace cache: 12K-uops, 8-way set associative
> 2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64 byte line size
> real memory  = 1073741824 (1024 MB)
> Physical memory chunk(s):
> 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
> 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
> 0x0000000001426000 - 0x000000003eda4fff, 1033367552 bytes (252287 pages)
> avail memory = 1032069120 (984 MB)
> Table 'FACP' at 0x3fff0030
> Table 'APIC' at 0x3fff00b0
> APIC: Found table at 0x3fff00b0
> MP Configuration Table version 1.4 found at 0xc00f0cb0
> APIC: Using the MADT enumerator.
> MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
> SMP: Added CPU 0 (AP)
> MADT: Found CPU APIC ID 0 ACPI ID 1: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 2: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 3: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 4: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 5: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 6: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 7: disabled
> ACPI APIC Table: <RCC    GCHE    >
> APIC: CPU 0 has ACPI ID 0
> bios32: Found BIOS32 Service Directory header at 0xc00fdb70
> bios32: Entry = 0xfdb80 (c00fdb80)  Rev = 0  Len = 1
> pcibios: PCI BIOS entry at 0xf0000+0xdba1
> pnpbios: Found PnP BIOS data at 0xc00f4500
> pnpbios: Entry = f0000:33a4  Rev = 1.0
> Other BIOS signatures found:
> x86bios:   IVT 0x000000-0x0004ff at 0xc0000000
> x86bios:  SSEG 0x09e000-0x09efff at 0xc4dc0000
> x86bios:  EBDA 0x09f000-0x09ffff at 0xc009f000
> x86bios:   ROM 0x0a0000-0x0fefff at 0xc00a0000
> ULE: setup cpu 0
> ACPI: RSDP 0xff900 00014 (v00 AMI   )
> ACPI: RSDT 0x3fff0000 0002C (v01 RCC    GCHE     00000001 MSFT 01000000)
> ACPI: FACP 0x3fff0030 00074 (v01 RCC    GCHE     00000001 MSFT 01000000)
> ACPI: DSDT 0x3fff0150 049F1 (v01    RCC     GCSL 00000100 MSFT 0100000D)
> ACPI: FACS 0x3ffff000 00040
> ACPI: APIC 0x3fff00b0 0009A (v01 RCC    GCHE     00000001 MSFT 01000000)
> MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000
> ioapic0: Routing external 8259A's -> intpin 0
> MADT: Found IO APIC ID 9, Interrupt 16 at 0xfec01000
> MADT: Found IO APIC ID 10, Interrupt 32 at 0xfec02000
> MADT: Interrupt override: source 0, irq 2
> ioapic0: Routing IRQ 0 -> intpin 2
> MADT: Forcing active-low polarity and level trigger for SCI
> ioapic0: intpin 9 polarity: low
> ioapic0: intpin 9 trigger: level
> ioapic0 <Version 1.1> irqs 0-15 on motherboard
> ioapic1 <Version 1.1> irqs 16-31 on motherboard
> ioapic2 <Version 1.1> irqs 32-47 on motherboard
> cpu0 BSP:
>      ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
>   lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
>   timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
> wlan: <802.11 Link Layer>
> random: <entropy source, Software, Yarrow>
> nfslock: pseudo-device
> kbd: new array size 4
> kbd1 at kbdmux0
> mem: <memory>
> Pentium Pro MTRR support enabled
> io: <I/O>
> null: <null device, zero device>
> hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
> acpi0: <RCC GCHE> on motherboard
> ACPI Warning: Type override - [DEB_] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [MLIB] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [IO__] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [DATA] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [ICNT] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [ACPI] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [IORG] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [BIOS] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [CMOS] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [KBC_] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [OEM_] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
> acpi0: [MPSAFE]
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> acpi0: wakeup code va 0xc4dbd000 pa 0x1000
> pci_open(1):	mode 1 addr port (0x0cf8) is 0x800078ac
> pci_open(1a):	mode1res=0x80000000 (0x80000000)
> pci_cfgcheck:	device 0 [class=060000] [hdr=80] is there (id=00171166)
> pcibios: BIOS version 2.10
> unknown: I/O range not supported
> acpi0: reservation of 0, a0000 (3) failed
> acpi0: reservation of 100000, 3ff00000 (3) failed
> ACPI timer: 1/2 0/3 1/2 1/2 0/3 1/2 0/3 1/2 0/3 0/4 -> 5
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
> cpu0: <ACPI CPU> on acpi0
> cpu0: switching to generic Cx mode
> ACPI: Processor \\_PR_.CPU1 (ACPI ID 1) ignored
> ACPI: Processor \\_PR_.CPU2 (ACPI ID 2) ignored
> ACPI: Processor \\_PR_.CPU3 (ACPI ID 3) ignored
> ACPI: Processor \\_PR_.CPU4 (ACPI ID 4) ignored
> ACPI: Processor \\_PR_.CPU5 (ACPI ID 5) ignored
> ACPI: Processor \\_PR_.CPU6 (ACPI ID 6) ignored
> ACPI: Processor \\_PR_.CPU7 (ACPI ID 7) ignored
> pci_link0:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link1:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link2:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link3:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link4:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link5:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link6:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link7:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link8:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link9:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link10:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link11:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link12:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link13:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link14:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link15:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link16:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link17:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link18:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link19:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link20:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link21:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link22:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link23:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link24:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link25:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link26:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link27:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link28:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link29:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link30:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link31:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link32:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0   10   N     0  10
>   Validation          0   10   N     0  10
>   After Disable       0  255   N     0  10
> pci_link33:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  11
>   Validation          0  255   N     0  11
>   After Disable       0  255   N     0  11
> acpi_button0: <Sleep Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> ACPI: Found matching pin for 0.15.INTA at func 2: 10
> pci0: <ACPI PCI bus> on pcib0
> pci0: domain=0, physical bus=0
> found->	vendor=0x1166, dev=0x0017, revid=0x32
> 	domain=0, bus=0, slot=0, func=0
> 	class=06-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x1166, dev=0x0017, revid=0x00
> 	domain=0, bus=0, slot=0, func=1
> 	class=06-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x8086, dev=0x1026, revid=0x04
> 	domain=0, bus=0, slot=1, func=0
> 	class=02-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=5
> 	powerspec 2  supports D0 D3  current D0
> 	map[10]: type Memory, range 64, base 0xfeb60000, size 17, enabled
> 	map[18]: type Memory, range 64, base 0xfeb00000, size 18, enabled
> 	map[20]: type I/O Port, range 32, base 0xe000, size  6, enabled
> pcib0: matched entry for 0.1.INTA
> pcib0: slot 1 INTA hardwired to IRQ 16
> found->	vendor=0x1002, dev=0x4752, revid=0x27
> 	domain=0, bus=0, slot=6, func=0
> 	class=03-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=10
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> 	map[10]: type Memory, range 32, base 0xfd000000, size 24, enabled
> 	map[14]: type I/O Port, range 32, base 0xe800, size  8, enabled
> 	map[18]: type Memory, range 32, base 0xfebff000, size 12, enabled
> pcib0: matched entry for 0.6.INTA
> pcib0: slot 6 INTA hardwired to IRQ 26
> found->	vendor=0x8086, dev=0x1229, revid=0x10
> 	domain=0, bus=0, slot=7, func=0
> 	class=02-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
> 	intpin=a, irq=9
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> 	map[10]: type Memory, range 32, base 0xfebfd000, size 12, enabled
> 	map[14]: type I/O Port, range 32, base 0xe400, size  6, enabled
> 	map[18]: type Memory, range 32, base 0xfeb80000, size 17, enabled
> pcib0: matched entry for 0.7.INTA
> pcib0: slot 7 INTA hardwired to IRQ 27
> found->	vendor=0x14e4, dev=0x16a6, revid=0x02
> 	domain=0, bus=0, slot=8, func=0
> 	class=02-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> 	powerspec 2  supports D0 D3  current D0
> 	MSI supports 8 messages, 64 bit
> 	map[10]: type Memory, range 64, base 0xfebe0000, size 16, enabled
> pcib0: matched entry for 0.8.INTA
> pcib0: slot 8 INTA hardwired to IRQ 28
> found->	vendor=0x1166, dev=0x0203, revid=0xa0
> 	domain=0, bus=0, slot=15, func=0
> 	class=06-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0107, statreg=0x2200, cachelnsz=0 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x1166, dev=0x0213, revid=0xa0
> 	domain=0, bus=0, slot=15, func=1
> 	class=01-01-8a, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0015, statreg=0x0200, cachelnsz=8 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	map[20]: type I/O Port, range 32, base 0xffa0, size  4, enabled
> found->	vendor=0x1166, dev=0x0221, revid=0x05
> 	domain=0, bus=0, slot=15, func=2
> 	class=0c-03-10, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
> 	intpin=a, irq=10
> 	map[10]: type Memory, range 32, base 0xfebfe000, size 12, enabled
> pcib0: matched entry for 0.15.INTA (src \\_SB_.LNUS:0)
> ioapic0: Changing trigger for pin 10 to level
> ioapic0: Changing polarity for pin 10 to low
> pcib0: slot 15 INTA routed to irq 10 via \\_SB_.LNUS
> unknown: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfe000
> ohci early: SMM active, request owner change
> found->	vendor=0x1166, dev=0x0227, revid=0x00
> 	domain=0, bus=0, slot=15, func=3
> 	class=06-01-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0107, statreg=0x0200, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> em0: <Intel(R) PRO/1000 Legacy Network Connection 1.0.5> port 0xe000-0xe03f mem 0xfeb60000-0xfeb7ffff,0xfeb00000-0xfeb3ffff irq 16 at device 1.0 on pci0
> em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfeb60000
> em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0xe000
> ioapic1: routing intpin 0 (PCI IRQ 16) to lapic 0 vector 49
> em0: [FILTER]
> em0: bpf attached
> em0: Ethernet address: 00:04:23:df:fa:46
> vgapci0: <VGA-compatible display> port 0xe800-0xe8ff mem 0xfd000000-0xfdffffff,0xfebff000-0xfebfffff irq 26 at device 6.0 on pci0
> fxp0: <Intel 82551 Pro/100 Ethernet> port 0xe400-0xe43f mem 0xfebfd000-0xfebfdfff,0xfeb80000-0xfeb9ffff irq 27 at device 7.0 on pci0
> fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfd000
> fxp0: using memory space register mapping
> fxp0: PCI IDs: 8086 1229 8086 1050 0010
> fxp0: Dynamic Standby mode is disabled
> miibus0: <MII bus> on fxp0
> inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
> inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
> fxp0: bpf attached
> fxp0: Ethernet address: 00:30:48:52:51:ae
> ioapic1: routing intpin 11 (PCI IRQ 27) to lapic 0 vector 50
> fxp0: [MPSAFE]
> fxp0: [ITHREAD]
> pci0:0:8:0: bad VPD cksum, remain 14
> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x001002> mem 0xfebe0000-0xfebeffff irq 28 at device 8.0 on pci0
> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfebe0000
> bge0: CHIP ID 0x00001002; ASIC REV 0x01; CHIP REV 0x10; PCI on PCI-X 33 MHz; 32bit
> miibus1: <MII bus> on bge0
> brgphy0: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus1
> brgphy0: OUI 0x000818, model 0x0016, rev. 2
> brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
> bge0: bpf attached
> bge0: Ethernet address: 00:30:48:52:51:af
> ioapic1: routing intpin 12 (PCI IRQ 28) to lapic 0 vector 51
> bge0: [MPSAFE]
> bge0: [ITHREAD]
> atapci0: <ServerWorks CSB6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 15.1 on pci0
> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
> ata0: <ATA channel> at channel 0 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
> atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
> ata0: reset tp1 mask=03 ostat0=50 ostat1=00
> ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
> ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
> ata0: reset tp2 stat0=50 stat1=00 devices=0x1
> ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 52
> ata0: [MPSAFE]
> ata0: [ITHREAD]
> ata1: <ATA channel> at channel 1 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
> atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
> ata1: reset tp1 mask=01 ostat0=50 ostat1=ff
> ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata1: reset tp2 stat0=00 stat1=00 devices=0x10000
> ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 53
> ata1: [MPSAFE]
> ata1: [ITHREAD]
> ohci0: <OHCI (generic) USB controller> mem 0xfebfe000-0xfebfefff irq 10 at device 15.2 on pci0
> ohci0: (New OHCI DeviceId=0x02211166)
> ioapic0: routing intpin 10 (ISA IRQ 10) to lapic 0 vector 54
> ohci0: [MPSAFE]
> ohci0: [ITHREAD]
> usbus0 on ohci0
> usbus0: bpf attached
> ohci0: usbpf: Attached
> isab0: <PCI-ISA bridge> at device 15.3 on pci0
> isa0: <ISA bus> on isab0
> atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
> atrtc0: registered as a time-of-day clock (resolution 1000000us)
> psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0065
> atkbd: keyboard ID 0x41ab (2)
> kbd0 at atkbd0
> kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
> ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 55
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> psm0: current command byte:0065
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 56
> psm0: [GIANT-LOCKED]
> psm0: [ITHREAD]
> psm0: model IntelliMouse, device ID 3-00, 3 buttons
> psm0: config:00000000, flags:00000008, packet size:4
> psm0: syncmask:08, syncbits:00
> fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f3,0x3f4-0x3f5,0x3f7 irq 6 drq 2 on acpi0
> fdc0: ic_type 90 part_id 73
> ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 0 vector 57
> fdc0: [FILTER]
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 58
> uart0: [FILTER]
> uart0: fast interrupt
> uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
> ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 0 vector 59
> uart1: [FILTER]
> uart1: fast interrupt
> ppc0: using extended I/O port range
> ppc0: SPP ECP 
> ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
> ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/8 bytes threshold
> ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 60
> ppc0: [MPSAFE]
> ppc0: [ITHREAD]
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> plip0: bpf attached
> plip0: [MPSAFE]
> plip0: [ITHREAD]
> lpt0: <Printer> on ppbus0
> lpt0: [MPSAFE]
> lpt0: [ITHREAD]
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> ex_isa_identify()
> pnp_identify: Trying Read_Port at 203
> pnp_identify: Trying Read_Port at 243
> pnp_identify: Trying Read_Port at 283
> pnp_identify: Trying Read_Port at 2c3
> pnp_identify: Trying Read_Port at 303
> pnp_identify: Trying Read_Port at 343
> pnp_identify: Trying Read_Port at 383
> pnp_identify: Trying Read_Port at 3c3
> PNP Identify complete
> ahc_isa_probe 0: ioport 0xc00 alloc failed
> ahc_isa_probe 1: ioport 0x1c00 alloc failed
> ahc_isa_probe 2: ioport 0x2c00 alloc failed
> ahc_isa_probe 3: ioport 0x3c00 alloc failed
> ahc_isa_probe 4: ioport 0x4c00 alloc failed
> ahc_isa_probe 5: ioport 0x5c00 alloc failed
> ahc_isa_probe 6: ioport 0x6c00 alloc failed
> ahc_isa_probe 7: ioport 0x7c00 alloc failed
> ahc_isa_probe 8: ioport 0x8c00 alloc failed
> ahc_isa_probe 9: ioport 0x9c00 alloc failed
> ahc_isa_probe 10: ioport 0xac00 alloc failed
> ahc_isa_probe 11: ioport 0xbc00 alloc failed
> ahc_isa_probe 12: ioport 0xcc00 alloc failed
> ahc_isa_probe 13: ioport 0xdc00 alloc failed
> ahc_isa_probe 14: ioport 0xec00 alloc failed
> isa_probe_children: disabling PnP devices
> pmtimer0 on isa0
> ata: ata0 already exists; skipping it
> ata: ata1 already exists; skipping it
> atkbdc: atkbdc0 already exists; skipping it
> atrtc: atrtc0 already exists; skipping it
> fdc: fdc0 already exists; skipping it
> ppc: ppc0 already exists; skipping it
> sc: sc0 already exists; skipping it
> uart: uart0 already exists; skipping it
> uart: uart1 already exists; skipping it
> isa_probe_children: probing non-PnP devices
> orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff pnpid ORM0000 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> wbwd0 failed to probe on isa0
> isa_probe_children: probing PnP devices
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> Device configuration finished.
> procfs registered
> lapic: Divisor 2, Frequency 66669679 Hz
> Timecounter "TSC" frequency 2666786988 Hz quality 800
> Timecounters tick every 1.000 msec
> vlan: initialized, using hash tables with chaining
> ipfw2 (+ipv6) initialized, divert enabled, nat loadable, rule-based forwarding disabled, default to accept, logging disabled
> ipfw0: bpf attached
> lo0: bpf attached
> hptrr: no controller detected.
> ata0: Identifying devices: 00000001
> ata0: New devices: 00000001
> usbus0: 12Mbps Full Speed USB v1.0
> ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
> ad0: setting UDMA100
> ad0: 152627MB <WDC WD1600LB-55EDA0 15.05R15> at ata0-master UDMA100 
> ad0: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
> ugen0.1: <0x1166> at usbus0
> uhub0: <0x1166 OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
> ad0: Adaptec check1 failed
> ad0: LSI (v3) check1 failed
> ad0: LSI (v2) check1 failed
> ad0: FreeBSD check1 failed
> ata1: Identifying devices: 00010000
> ata1: New devices: 00010000
> ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
> acd0: setting UDMA33
> acd0: <MATSHITA CR-177/7T0D> CDROM drive at ata1 as master
> acd0: read 4125KB/s (4125KB/s), 128KB buffer, UDMA33 
> acd0: Reads: CDR, CDRW, CDDA stream, packet
> acd0: Writes:
> acd0: Audio: play, 256 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: no/blank disc
> ATA PseudoRAID loaded
> uhub0: 4 ports with 4 removable, self powered
> GEOM: new disk ad0
> GEOM: ad0s2: geometry does not match label (255h,63s != 16h,63s).
> Trying to mount root from ufs:/dev/ad0s2a
> start_init: trying /sbin/init
> em0: Link is up 1000 Mbps Full Duplex
> em0: Link is Down
> em0: Link is up 1000 Mbps Full Duplex
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> splash: image decoder found: daemon_saver
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP
> fxp0: link state changed to DOWN
> fxp0: link state changed to UP

> Copyright (c) 1992-2012 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 8.3-RELEASE-p8 #46: Sat May 11 00:05:26 EDT 2013
>     root at familysquires.net:/usr/obj/usr/src/sys/NEWGATE i386
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc102d000.
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Calibrating TSC clock ... TSC clock: 2666782592 Hz
> CPU: Intel(R) Xeon(TM) CPU 2.66GHz (2666.78-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0xf25  Family = f  Model = 2  Stepping = 5
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0x4400<CNXT-ID,xTPR>
> 
> Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 128 entries
> Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
> 1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64 byte line size
> Trace cache: 12K-uops, 8-way set associative
> 2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64 byte line size
> real memory  = 1073741824 (1024 MB)
> Physical memory chunk(s):
> 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
> 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
> 0x0000000001426000 - 0x000000003eda4fff, 1033367552 bytes (252287 pages)
> avail memory = 1032085504 (984 MB)
> Table 'FACP' at 0x3fff0030
> Table 'APIC' at 0x3fff00b0
> APIC: Found table at 0x3fff00b0
> MP Configuration Table version 1.4 found at 0xc00f0cb0
> APIC: Using the MADT enumerator.
> MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
> SMP: Added CPU 0 (AP)
> MADT: Found CPU APIC ID 0 ACPI ID 1: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 2: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 3: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 4: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 5: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 6: disabled
> MADT: Found CPU APIC ID 0 ACPI ID 7: disabled
> ACPI APIC Table: <RCC    GCHE    >
> APIC: CPU 0 has ACPI ID 0
> bios32: Found BIOS32 Service Directory header at 0xc00fdb70
> bios32: Entry = 0xfdb80 (c00fdb80)  Rev = 0  Len = 1
> pcibios: PCI BIOS entry at 0xf0000+0xdba1
> pnpbios: Found PnP BIOS data at 0xc00f4500
> pnpbios: Entry = f0000:33a4  Rev = 1.0
> Other BIOS signatures found:
> x86bios:   IVT 0x000000-0x0004ff at 0xc0000000
> x86bios:  SSEG 0x010000-0x01ffff at 0xc43b9000
> x86bios:  EBDA 0x09f000-0x09ffff at 0xc009f000
> x86bios:   ROM 0x0a0000-0x0effff at 0xc00a0000
> ULE: setup cpu 0
> ACPI: RSDP 0xff900 00014 (v00 AMI   )
> ACPI: RSDT 0x3fff0000 0002C (v01 RCC    GCHE     00000001 MSFT 01000000)
> ACPI: FACP 0x3fff0030 00074 (v01 RCC    GCHE     00000001 MSFT 01000000)
> ACPI: DSDT 0x3fff0150 049F1 (v01    RCC     GCSL 00000100 MSFT 0100000D)
> ACPI: FACS 0x3ffff000 00040
> ACPI: APIC 0x3fff00b0 0009A (v01 RCC    GCHE     00000001 MSFT 01000000)
> MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000
> ioapic0: Routing external 8259A's -> intpin 0
> MADT: Found IO APIC ID 9, Interrupt 16 at 0xfec01000
> MADT: Found IO APIC ID 10, Interrupt 32 at 0xfec02000
> MADT: Interrupt override: source 0, irq 2
> ioapic0: Routing IRQ 0 -> intpin 2
> MADT: Forcing active-low polarity and level trigger for SCI
> ioapic0: intpin 9 polarity: low
> ioapic0: intpin 9 trigger: level
> ioapic0 <Version 1.1> irqs 0-15 on motherboard
> ioapic1 <Version 1.1> irqs 16-31 on motherboard
> ioapic2 <Version 1.1> irqs 32-47 on motherboard
> cpu0 BSP:
>      ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
>   lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
>   timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
> wlan: <802.11 Link Layer>
> null: <null device, zero device>
> random: <entropy source, Software, Yarrow>
> nfslock: pseudo-device
> io: <I/O>
> kbd: new array size 4
> kbd1 at kbdmux0
> mem: <memory>
> Pentium Pro MTRR support enabled
> hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
> acpi0: <RCC GCHE> on motherboard
> ACPI Warning: Type override - [DEB_] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [MLIB] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [IO__] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [DATA] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [ICNT] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [ACPI] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [IORG] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [BIOS] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [CMOS] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [KBC_] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ACPI Warning: Type override - [OEM_] had invalid type (Integer) for Scope operator, changed to type ANY
>  (20101013/dswload-808)
> ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
> acpi0: [MPSAFE]
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> acpi0: wakeup code va 0xc43b6000 pa 0x1000
> pci_open(1):	mode 1 addr port (0x0cf8) is 0x800078ac
> pci_open(1a):	mode1res=0x80000000 (0x80000000)
> pci_cfgcheck:	device 0 [class=060000] [hdr=80] is there (id=00171166)
> pcibios: BIOS version 2.10
> unknown: I/O range not supported
> acpi0: reservation of 0, a0000 (3) failed
> acpi0: reservation of 100000, 3ff00000 (3) failed
> ACPI timer: 0/3 1/2 1/2 0/3 0/3 0/3 1/2 0/3 0/3 0/3 -> 3
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
> cpu0: <ACPI CPU> on acpi0
> cpu0: switching to generic Cx mode
> pci_link0:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link1:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link2:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link3:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link4:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link5:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link6:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link7:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link8:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link9:        Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link10:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link11:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link12:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link13:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link14:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link15:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link16:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link17:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link18:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link19:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link20:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link21:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link22:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link23:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link24:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link25:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link26:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link27:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link28:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link29:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link30:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link31:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  3 4 5 7 9 11 12 14 15
>   Validation          0  255   N     0  3 4 5 7 9 11 12 14 15
>   After Disable       0  255   N     0  3 4 5 7 9 11 12 14 15
> pci_link32:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0   10   N     0  10
>   Validation          0   10   N     0  10
>   After Disable       0  255   N     0  10
> pci_link33:       Index  IRQ  Rtd  Ref  IRQs
>   Initial Probe       0  255   N     0  11
>   Validation          0  255   N     0  11
>   After Disable       0  255   N     0  11
> acpi_button0: <Sleep Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> ACPI: Found matching pin for 0.15.INTA at func 2: 10
> pci0: <ACPI PCI bus> on pcib0
> pci0: domain=0, physical bus=0
> found->	vendor=0x1166, dev=0x0017, revid=0x32
> 	domain=0, bus=0, slot=0, func=0
> 	class=06-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x1166, dev=0x0017, revid=0x00
> 	domain=0, bus=0, slot=0, func=1
> 	class=06-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x8086, dev=0x1026, revid=0x04
> 	domain=0, bus=0, slot=1, func=0
> 	class=02-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=5
> 	powerspec 2  supports D0 D3  current D0
> 	map[10]: type Memory, range 64, base 0xfeb60000, size 17, enabled
> 	map[18]: type Memory, range 64, base 0xfeb00000, size 18, enabled
> 	map[20]: type I/O Port, range 32, base 0xe000, size  6, enabled
> pcib0: matched entry for 0.1.INTA
> pcib0: slot 1 INTA hardwired to IRQ 16
> found->	vendor=0x1002, dev=0x4752, revid=0x27
> 	domain=0, bus=0, slot=6, func=0
> 	class=03-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=10
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> 	map[10]: type Memory, range 32, base 0xfd000000, size 24, enabled
> 	map[14]: type I/O Port, range 32, base 0xe800, size  8, enabled
> 	map[18]: type Memory, range 32, base 0xfebff000, size 12, enabled
> pcib0: matched entry for 0.6.INTA
> pcib0: slot 6 INTA hardwired to IRQ 26
> found->	vendor=0x8086, dev=0x1229, revid=0x10
> 	domain=0, bus=0, slot=7, func=0
> 	class=02-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
> 	intpin=a, irq=9
> 	powerspec 2  supports D0 D1 D2 D3  current D0
> 	map[10]: type Memory, range 32, base 0xfebfd000, size 12, enabled
> 	map[14]: type I/O Port, range 32, base 0xe400, size  6, enabled
> 	map[18]: type Memory, range 32, base 0xfeb80000, size 17, enabled
> pcib0: matched entry for 0.7.INTA
> pcib0: slot 7 INTA hardwired to IRQ 27
> found->	vendor=0x14e4, dev=0x16a6, revid=0x02
> 	domain=0, bus=0, slot=8, func=0
> 	class=02-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> 	powerspec 2  supports D0 D3  current D0
> 	MSI supports 8 messages, 64 bit
> 	map[10]: type Memory, range 64, base 0xfebe0000, size 16, enabled
> pcib0: matched entry for 0.8.INTA
> pcib0: slot 8 INTA hardwired to IRQ 28
> found->	vendor=0x1166, dev=0x0203, revid=0xa0
> 	domain=0, bus=0, slot=15, func=0
> 	class=06-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0107, statreg=0x2200, cachelnsz=0 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x1166, dev=0x0213, revid=0xa0
> 	domain=0, bus=0, slot=15, func=1
> 	class=01-01-8a, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0015, statreg=0x0200, cachelnsz=8 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	map[20]: type I/O Port, range 32, base 0xffa0, size  4, enabled
> found->	vendor=0x1166, dev=0x0221, revid=0x05
> 	domain=0, bus=0, slot=15, func=2
> 	class=0c-03-10, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords)
> 	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
> 	intpin=a, irq=10
> 	map[10]: type Memory, range 32, base 0xfebfe000, size 12, enabled
> pcib0: matched entry for 0.15.INTA (src \\_SB_.LNUS:0)
> ioapic0: Changing trigger for pin 10 to level
> ioapic0: Changing polarity for pin 10 to low
> pcib0: slot 15 INTA routed to irq 10 via \\_SB_.LNUS
> unknown: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfe000
> ohci early: SMM active, request owner change
> found->	vendor=0x1166, dev=0x0227, revid=0x00
> 	domain=0, bus=0, slot=15, func=3
> 	class=06-01-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0107, statreg=0x0200, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> em0: <Intel(R) PRO/1000 Legacy Network Connection 1.0.4> port 0xe000-0xe03f mem 0xfeb60000-0xfeb7ffff,0xfeb00000-0xfeb3ffff irq 16 at device 1.0 on pci0
> em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfeb60000
> em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0xe000
> ioapic1: routing intpin 0 (PCI IRQ 16) to lapic 0 vector 49
> em0: [FILTER]
> em0: bpf attached
> em0: Ethernet address: 00:04:23:df:fa:46
> vgapci0: <VGA-compatible display> port 0xe800-0xe8ff mem 0xfd000000-0xfdffffff,0xfebff000-0xfebfffff irq 26 at device 6.0 on pci0
> fxp0: <Intel 82551 Pro/100 Ethernet> port 0xe400-0xe43f mem 0xfebfd000-0xfebfdfff,0xfeb80000-0xfeb9ffff irq 27 at device 7.0 on pci0
> fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfd000
> fxp0: using memory space register mapping
> fxp0: PCI IDs: 8086 1229 8086 1050 0010
> fxp0: Dynamic Standby mode is disabled
> miibus0: <MII bus> on fxp0
> inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
> inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
> fxp0: bpf attached
> fxp0: Ethernet address: 00:30:48:52:51:ae
> ioapic1: routing intpin 11 (PCI IRQ 27) to lapic 0 vector 50
> fxp0: [MPSAFE]
> fxp0: [ITHREAD]
> pci0:0:8:0: bad VPD cksum, remain 14
> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x001002> mem 0xfebe0000-0xfebeffff irq 28 at device 8.0 on pci0
> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfebe0000
> bge0: CHIP ID 0x00001002; ASIC REV 0x01; CHIP REV 0x10; PCI
> miibus1: <MII bus> on bge0
> brgphy0: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus1
> brgphy0: OUI 0x000818, model 0x0016, rev. 2
> brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
> bge0: bpf attached
> bge0: Ethernet address: 00:30:48:52:51:af
> ioapic1: routing intpin 12 (PCI IRQ 28) to lapic 0 vector 51
> bge0: [MPSAFE]
> bge0: [ITHREAD]
> atapci0: <ServerWorks CSB6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 15.1 on pci0
> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
> ata0: <ATA channel> at channel 0 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
> atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
> ata0: reset tp1 mask=03 ostat0=50 ostat1=00
> ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
> ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
> ata0: reset tp2 stat0=50 stat1=00 devices=0x1
> ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 52
> ata0: [MPSAFE]
> ata0: [ITHREAD]
> ata1: <ATA channel> at channel 1 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
> atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
> ata1: reset tp1 mask=01 ostat0=50 ostat1=ff
> ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata1: reset tp2 stat0=00 stat1=00 devices=0x10000
> ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 53
> ata1: [MPSAFE]
> ata1: [ITHREAD]
> ohci0: <OHCI (generic) USB controller> mem 0xfebfe000-0xfebfefff irq 10 at device 15.2 on pci0
> ohci0: (New OHCI DeviceId=0x02211166)
> ioapic0: routing intpin 10 (ISA IRQ 10) to lapic 0 vector 54
> ohci0: [MPSAFE]
> ohci0: [ITHREAD]
> usbus0: <OHCI (generic) USB controller> on ohci0
> usbus0: bpf attached
> ohci0: usbpf: Attached
> isab0: <PCI-ISA bridge> at device 15.3 on pci0
> isa0: <ISA bus> on isab0
> atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
> atrtc0: registered as a time-of-day clock (resolution 1000000us)
> psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0065
> atkbd: keyboard ID 0x41ab (2)
> kbd0 at atkbd0
> kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
> ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 55
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> psm0: current command byte:0065
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 56
> psm0: [GIANT-LOCKED]
> psm0: [ITHREAD]
> psm0: model IntelliMouse, device ID 3-00, 3 buttons
> psm0: config:00000000, flags:00000008, packet size:4
> psm0: syncmask:08, syncbits:00
> fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f3,0x3f4-0x3f5,0x3f7 irq 6 drq 2 on acpi0
> fdc0: ic_type 90 part_id 73
> ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 0 vector 57
> fdc0: [FILTER]
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 58
> uart0: [FILTER]
> uart0: fast interrupt
> uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
> ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 0 vector 59
> uart1: [FILTER]
> uart1: fast interrupt
> ppc0: using extended I/O port range
> ppc0: SPP ECP 
> ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
> ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/8 bytes threshold
> ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 60
> ppc0: [MPSAFE]
> ppc0: [ITHREAD]
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> plip0: bpf attached
> plip0: [MPSAFE]
> plip0: [ITHREAD]
> lpt0: <Printer> on ppbus0
> lpt0: [MPSAFE]
> lpt0: [ITHREAD]
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> ahc_isa_probe 0: ioport 0xc00 alloc failed
> ex_isa_identify()
> pnp_identify: Trying Read_Port at 203
> pnp_identify: Trying Read_Port at 243
> pnp_identify: Trying Read_Port at 283
> pnp_identify: Trying Read_Port at 2c3
> pnp_identify: Trying Read_Port at 303
> pnp_identify: Trying Read_Port at 343
> pnp_identify: Trying Read_Port at 383
> pnp_identify: Trying Read_Port at 3c3
> PNP Identify complete
> isa_probe_children: disabling PnP devices
> pmtimer0 on isa0
> ata: ata0 already exists; skipping it
> ata: ata1 already exists; skipping it
> atkbdc: atkbdc0 already exists; skipping it
> atrtc: atrtc0 already exists; skipping it
> fdc: fdc0 already exists; skipping it
> ppc: ppc0 already exists; skipping it
> sc: sc0 already exists; skipping it
> uart: uart0 already exists; skipping it
> uart: uart1 already exists; skipping it
> isa_probe_children: probing non-PnP devices
> orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff pnpid ORM0000 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> isa_probe_children: probing PnP devices
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> Device configuration finished.
> procfs registered
> lapic: Divisor 2, Frequency 66669589 Hz
> Timecounter "TSC" frequency 2666782592 Hz quality 800
> Timecounters tick every 1.000 msec
> vlan: initialized, using hash tables with chaining
> ipfw2 (+ipv6) initialized, divert enabled, nat loadable, rule-based forwarding disabled, default to accept, logging disabled
> ipfw0: bpf attached
> lo0: bpf attached
> hptrr: no controller detected.
> ata0: Identifying devices: 00000001
> ata0: New devices: 00000001
> usbus0: 12Mbps Full Speed USB v1.0
> ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
> ad0: setting UDMA100
> ad0: 152627MB <WDC WD1600LB-55EDA0 15.05R15> at ata0-master UDMA100 
> ad0: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
> ugen0.1: <0x1166> at usbus0
> uhub0: <0x1166 OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
> ad0: Adaptec check1 failed
> ad0: LSI (v3) check1 failed
> ad0: LSI (v2) check1 failed
> ad0: FreeBSD check1 failed
> ata1: Identifying devices: 00010000
> ata1: New devices: 00010000
> ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
> acd0: setting UDMA33
> acd0: <MATSHITA CR-177/7T0D> CDROM drive at ata1 as master
> acd0: read 4125KB/s (4125KB/s), 128KB buffer, UDMA33 
> acd0: Reads: CDR, CDRW, CDDA stream, packet
> acd0: Writes:
> acd0: Audio: play, 256 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: no/blank disc
> ATA PseudoRAID loaded
> uhub0: 4 ports with 4 removable, self powered
> GEOM: new disk ad0
> GEOM: ad0s2: geometry does not match label (255h,63s != 16h,63s).
> Trying to mount root from ufs:/dev/ad0s2a
> start_init: trying /sbin/init
> em0: Link is up 1000 Mbps Full Duplex
> em0: Link is Down
> em0: Link is up 1000 Mbps Full Duplex
> splash: image decoder found: daemon_saver

CC'ing Yong-Hyeon PYUN who may be able to help with this.

If you could also provide "pciconf -lvbc" output that would be useful.

-- 
| Jeremy Chadwick                                   jdc at koitsu.org |
| UNIX Systems Administrator                http://jdc.koitsu.org/ |
| Mountain View, CA, US                                            |
| Making life hard for others since 1977.             PGP 4BD6C0CB |


More information about the freebsd-stable mailing list