Apparent fxp regression in FreeBSD 8.4-RC3
Michael L. Squires
mikes at siralan.org
Sun May 12 03:18:58 UTC 2013
I upgraded to FreeBSD 8.4-RC3 and noticed a problem with the fxp driver on
an older Supermicro single CPU single core Xeon motherboard.
I know that 8.3-Release does not have this issue, but don't know when in
the updates to that release the regression was introduced.
I use the fxp driver to connect to a Motorola Surfboard cable modem, and
immediately saw the following occur many times:
May 10 23:00:04 familysquires kernel: fxp0: link state changed to DOWN
May 10 23:00:04 familysquires dhclient: New Subnet Mask (fxp0):
255.255.240.0
May 10 23:00:04 familysquires dhclient: New Broadcast Address (fxp0):
255.255.25
5.255
May 10 23:00:04 familysquires dhclient: New Routers (fxp0): xx.xxx.xxx.1
May 10 23:00:06 familysquires kernel: fxp0: link state changed to UP
May 10 23:00:22 familysquires dhclient: New IP Address (fxp0):
xx.xxx.xxx.163
May 10 23:00:22 familysquires kernel: fxp0: link state changed to DOWN
May 10 23:00:22 familysquires dhclient: New Subnet Mask (fxp0):
255.255.240.0
May 10 23:00:22 familysquires dhclient: New Broadcast Address (fxp0):
255.255.255.255
May 10 23:00:22 familysquires dhclient: New Routers (fxp0): xx.xxx.xxx.1
May 10 23:00:24 familysquires kernel: fxp0: link state changed to UP
repeated without end.
I reinsalled 8.3-Release p8
FreeBSD familysquires.net 8.3-RELEASE-p8 FreeBSD 8.3-RELEASE-p8 #46: Sat
May 11 00:05:26 EDT 2013
which ended the string up fxp up/down messages. This kernel has now
operated for 24 hours without generating this error.
I've attached a verbose dmesg from 8.4-RC3 and a standard dmesg from
8.3-Release p8, and can provide whatever else you need.
This is not a critical issue for me. The system has an unused bge interface
(replaced by an Intel em0 interface during a previous bout of a problem with
the bge driver).
Mike Squires
mikes at siralan.org
-------------- next part --------------
Copyright (c) 1992-2013 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.4-PRERELEASE #45: Fri May 10 09:43:40 EDT 2013
root at familysquires.net:/usr/obj/usr/src/sys/NEWGATE i386
gcc version 4.2.1 20070831 patched [FreeBSD]
Preloaded elf kernel "/boot/kernel/kernel" at 0xc1060000.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2666786988 Hz
CPU: Intel(R) Xeon(TM) CPU 2.66GHz (2666.79-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf25 Family = f Model = 2 Stepping = 5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x4400<CNXT-ID,xTPR>
Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 128 entries
Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64 byte line size
Trace cache: 12K-uops, 8-way set associative
2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64 byte line size
real memory = 1073741824 (1024 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001426000 - 0x000000003eda4fff, 1033367552 bytes (252287 pages)
avail memory = 1032069120 (984 MB)
Table 'FACP' at 0x3fff0030
Table 'APIC' at 0x3fff00b0
APIC: Found table at 0x3fff00b0
MP Configuration Table version 1.4 found at 0xc00f0cb0
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 0 ACPI ID 1: disabled
MADT: Found CPU APIC ID 0 ACPI ID 2: disabled
MADT: Found CPU APIC ID 0 ACPI ID 3: disabled
MADT: Found CPU APIC ID 0 ACPI ID 4: disabled
MADT: Found CPU APIC ID 0 ACPI ID 5: disabled
MADT: Found CPU APIC ID 0 ACPI ID 6: disabled
MADT: Found CPU APIC ID 0 ACPI ID 7: disabled
ACPI APIC Table: <RCC GCHE >
APIC: CPU 0 has ACPI ID 0
bios32: Found BIOS32 Service Directory header at 0xc00fdb70
bios32: Entry = 0xfdb80 (c00fdb80) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xdba1
pnpbios: Found PnP BIOS data at 0xc00f4500
pnpbios: Entry = f0000:33a4 Rev = 1.0
Other BIOS signatures found:
x86bios: IVT 0x000000-0x0004ff at 0xc0000000
x86bios: SSEG 0x09e000-0x09efff at 0xc4dc0000
x86bios: EBDA 0x09f000-0x09ffff at 0xc009f000
x86bios: ROM 0x0a0000-0x0fefff at 0xc00a0000
ULE: setup cpu 0
ACPI: RSDP 0xff900 00014 (v00 AMI )
ACPI: RSDT 0x3fff0000 0002C (v01 RCC GCHE 00000001 MSFT 01000000)
ACPI: FACP 0x3fff0030 00074 (v01 RCC GCHE 00000001 MSFT 01000000)
ACPI: DSDT 0x3fff0150 049F1 (v01 RCC GCSL 00000100 MSFT 0100000D)
ACPI: FACS 0x3ffff000 00040
ACPI: APIC 0x3fff00b0 0009A (v01 RCC GCHE 00000001 MSFT 01000000)
MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
MADT: Found IO APIC ID 9, Interrupt 16 at 0xfec01000
MADT: Found IO APIC ID 10, Interrupt 32 at 0xfec02000
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0: intpin 9 polarity: low
ioapic0: intpin 9 trigger: level
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
ioapic2 <Version 1.1> irqs 32-47 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
wlan: <802.11 Link Layer>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
io: <I/O>
null: <null device, zero device>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
acpi0: <RCC GCHE> on motherboard
ACPI Warning: Type override - [DEB_] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [MLIB] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [IO__] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [DATA] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [ICNT] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [ACPI] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [IORG] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [BIOS] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [CMOS] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [KBC_] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [OEM_] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xc4dbd000 pa 0x1000
pci_open(1): mode 1 addr port (0x0cf8) is 0x800078ac
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00171166)
pcibios: BIOS version 2.10
unknown: I/O range not supported
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 3ff00000 (3) failed
ACPI timer: 1/2 0/3 1/2 1/2 0/3 1/2 0/3 1/2 0/3 0/4 -> 5
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
ACPI: Processor \\_PR_.CPU1 (ACPI ID 1) ignored
ACPI: Processor \\_PR_.CPU2 (ACPI ID 2) ignored
ACPI: Processor \\_PR_.CPU3 (ACPI ID 3) ignored
ACPI: Processor \\_PR_.CPU4 (ACPI ID 4) ignored
ACPI: Processor \\_PR_.CPU5 (ACPI ID 5) ignored
ACPI: Processor \\_PR_.CPU6 (ACPI ID 6) ignored
ACPI: Processor \\_PR_.CPU7 (ACPI ID 7) ignored
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link8: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link9: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link10: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link11: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link12: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link13: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link14: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link15: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link16: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link17: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link18: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link19: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link20: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link21: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link22: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link23: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link24: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link25: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link26: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link27: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link28: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link29: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link30: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link31: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link32: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 10
Validation 0 10 N 0 10
After Disable 0 255 N 0 10
pci_link33: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 11
Validation 0 255 N 0 11
After Disable 0 255 N 0 11
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.15.INTA at func 2: 10
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x1166, dev=0x0017, revid=0x32
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0017, revid=0x00
domain=0, bus=0, slot=0, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1026, revid=0x04
domain=0, bus=0, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 64, base 0xfeb60000, size 17, enabled
map[18]: type Memory, range 64, base 0xfeb00000, size 18, enabled
map[20]: type I/O Port, range 32, base 0xe000, size 6, enabled
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
found-> vendor=0x1002, dev=0x4752, revid=0x27
domain=0, bus=0, slot=6, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xfd000000, size 24, enabled
map[14]: type I/O Port, range 32, base 0xe800, size 8, enabled
map[18]: type Memory, range 32, base 0xfebff000, size 12, enabled
pcib0: matched entry for 0.6.INTA
pcib0: slot 6 INTA hardwired to IRQ 26
found-> vendor=0x8086, dev=0x1229, revid=0x10
domain=0, bus=0, slot=7, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xfebfd000, size 12, enabled
map[14]: type I/O Port, range 32, base 0xe400, size 6, enabled
map[18]: type Memory, range 32, base 0xfeb80000, size 17, enabled
pcib0: matched entry for 0.7.INTA
pcib0: slot 7 INTA hardwired to IRQ 27
found-> vendor=0x14e4, dev=0x16a6, revid=0x02
domain=0, bus=0, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
map[10]: type Memory, range 64, base 0xfebe0000, size 16, enabled
pcib0: matched entry for 0.8.INTA
pcib0: slot 8 INTA hardwired to IRQ 28
found-> vendor=0x1166, dev=0x0203, revid=0xa0
domain=0, bus=0, slot=15, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x2200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0213, revid=0xa0
domain=0, bus=0, slot=15, func=1
class=01-01-8a, hdrtype=0x00, mfdev=1
cmdreg=0x0015, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type I/O Port, range 32, base 0xffa0, size 4, enabled
found-> vendor=0x1166, dev=0x0221, revid=0x05
domain=0, bus=0, slot=15, func=2
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=a, irq=10
map[10]: type Memory, range 32, base 0xfebfe000, size 12, enabled
pcib0: matched entry for 0.15.INTA (src \\_SB_.LNUS:0)
ioapic0: Changing trigger for pin 10 to level
ioapic0: Changing polarity for pin 10 to low
pcib0: slot 15 INTA routed to irq 10 via \\_SB_.LNUS
unknown: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfe000
ohci early: SMM active, request owner change
found-> vendor=0x1166, dev=0x0227, revid=0x00
domain=0, bus=0, slot=15, func=3
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
em0: <Intel(R) PRO/1000 Legacy Network Connection 1.0.5> port 0xe000-0xe03f mem 0xfeb60000-0xfeb7ffff,0xfeb00000-0xfeb3ffff irq 16 at device 1.0 on pci0
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfeb60000
em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0xe000
ioapic1: routing intpin 0 (PCI IRQ 16) to lapic 0 vector 49
em0: [FILTER]
em0: bpf attached
em0: Ethernet address: 00:04:23:df:fa:46
vgapci0: <VGA-compatible display> port 0xe800-0xe8ff mem 0xfd000000-0xfdffffff,0xfebff000-0xfebfffff irq 26 at device 6.0 on pci0
fxp0: <Intel 82551 Pro/100 Ethernet> port 0xe400-0xe43f mem 0xfebfd000-0xfebfdfff,0xfeb80000-0xfeb9ffff irq 27 at device 7.0 on pci0
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfd000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 8086 1050 0010
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
fxp0: bpf attached
fxp0: Ethernet address: 00:30:48:52:51:ae
ioapic1: routing intpin 11 (PCI IRQ 27) to lapic 0 vector 50
fxp0: [MPSAFE]
fxp0: [ITHREAD]
pci0:0:8:0: bad VPD cksum, remain 14
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x001002> mem 0xfebe0000-0xfebeffff irq 28 at device 8.0 on pci0
bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfebe0000
bge0: CHIP ID 0x00001002; ASIC REV 0x01; CHIP REV 0x10; PCI on PCI-X 33 MHz; 32bit
miibus1: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy0: OUI 0x000818, model 0x0016, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: bpf attached
bge0: Ethernet address: 00:30:48:52:51:af
ioapic1: routing intpin 12 (PCI IRQ 28) to lapic 0 vector 51
bge0: [MPSAFE]
bge0: [ITHREAD]
atapci0: <ServerWorks CSB6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 15.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
ata0: <ATA channel> at channel 0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 52
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel> at channel 1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=01 ostat0=50 ostat1=ff
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0x10000
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 53
ata1: [MPSAFE]
ata1: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfebfe000-0xfebfefff irq 10 at device 15.2 on pci0
ohci0: (New OHCI DeviceId=0x02211166)
ioapic0: routing intpin 10 (ISA IRQ 10) to lapic 0 vector 54
ohci0: [MPSAFE]
ohci0: [ITHREAD]
usbus0 on ohci0
usbus0: bpf attached
ohci0: usbpf: Attached
isab0: <PCI-ISA bridge> at device 15.3 on pci0
isa0: <ISA bus> on isab0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 55
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 56
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f3,0x3f4-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 73
ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 0 vector 57
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 58
uart0: [FILTER]
uart0: fast interrupt
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 0 vector 59
uart1: [FILTER]
uart1: fast interrupt
ppc0: using extended I/O port range
ppc0: SPP ECP
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 60
ppc0: [MPSAFE]
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
plip0: [MPSAFE]
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [MPSAFE]
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ex_isa_identify()
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
ahc_isa_probe 0: ioport 0xc00 alloc failed
ahc_isa_probe 1: ioport 0x1c00 alloc failed
ahc_isa_probe 2: ioport 0x2c00 alloc failed
ahc_isa_probe 3: ioport 0x3c00 alloc failed
ahc_isa_probe 4: ioport 0x4c00 alloc failed
ahc_isa_probe 5: ioport 0x5c00 alloc failed
ahc_isa_probe 6: ioport 0x6c00 alloc failed
ahc_isa_probe 7: ioport 0x7c00 alloc failed
ahc_isa_probe 8: ioport 0x8c00 alloc failed
ahc_isa_probe 9: ioport 0x9c00 alloc failed
ahc_isa_probe 10: ioport 0xac00 alloc failed
ahc_isa_probe 11: ioport 0xbc00 alloc failed
ahc_isa_probe 12: ioport 0xcc00 alloc failed
ahc_isa_probe 13: ioport 0xdc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
isa_probe_children: disabling PnP devices
pmtimer0 on isa0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
uart: uart0 already exists; skipping it
uart: uart1 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
wbwd0 failed to probe on isa0
isa_probe_children: probing PnP devices
p4tcc0: <CPU Frequency Thermal Control> on cpu0
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 66669679 Hz
Timecounter "TSC" frequency 2666786988 Hz quality 800
Timecounters tick every 1.000 msec
vlan: initialized, using hash tables with chaining
ipfw2 (+ipv6) initialized, divert enabled, nat loadable, rule-based forwarding disabled, default to accept, logging disabled
ipfw0: bpf attached
lo0: bpf attached
hptrr: no controller detected.
ata0: Identifying devices: 00000001
ata0: New devices: 00000001
usbus0: 12Mbps Full Speed USB v1.0
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting UDMA100
ad0: 152627MB <WDC WD1600LB-55EDA0 15.05R15> at ata0-master UDMA100
ad0: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
ugen0.1: <0x1166> at usbus0
uhub0: <0x1166 OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1: Identifying devices: 00010000
ata1: New devices: 00010000
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting UDMA33
acd0: <MATSHITA CR-177/7T0D> CDROM drive at ata1 as master
acd0: read 4125KB/s (4125KB/s), 128KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ATA PseudoRAID loaded
uhub0: 4 ports with 4 removable, self powered
GEOM: new disk ad0
GEOM: ad0s2: geometry does not match label (255h,63s != 16h,63s).
Trying to mount root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
em0: Link is up 1000 Mbps Full Duplex
em0: Link is Down
em0: Link is up 1000 Mbps Full Duplex
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
splash: image decoder found: daemon_saver
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
fxp0: link state changed to DOWN
fxp0: link state changed to UP
-------------- next part --------------
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.3-RELEASE-p8 #46: Sat May 11 00:05:26 EDT 2013
root at familysquires.net:/usr/obj/usr/src/sys/NEWGATE i386
Preloaded elf kernel "/boot/kernel/kernel" at 0xc102d000.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2666782592 Hz
CPU: Intel(R) Xeon(TM) CPU 2.66GHz (2666.78-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf25 Family = f Model = 2 Stepping = 5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x4400<CNXT-ID,xTPR>
Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 128 entries
Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64 byte line size
Trace cache: 12K-uops, 8-way set associative
2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64 byte line size
real memory = 1073741824 (1024 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001426000 - 0x000000003eda4fff, 1033367552 bytes (252287 pages)
avail memory = 1032085504 (984 MB)
Table 'FACP' at 0x3fff0030
Table 'APIC' at 0x3fff00b0
APIC: Found table at 0x3fff00b0
MP Configuration Table version 1.4 found at 0xc00f0cb0
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 0 ACPI ID 1: disabled
MADT: Found CPU APIC ID 0 ACPI ID 2: disabled
MADT: Found CPU APIC ID 0 ACPI ID 3: disabled
MADT: Found CPU APIC ID 0 ACPI ID 4: disabled
MADT: Found CPU APIC ID 0 ACPI ID 5: disabled
MADT: Found CPU APIC ID 0 ACPI ID 6: disabled
MADT: Found CPU APIC ID 0 ACPI ID 7: disabled
ACPI APIC Table: <RCC GCHE >
APIC: CPU 0 has ACPI ID 0
bios32: Found BIOS32 Service Directory header at 0xc00fdb70
bios32: Entry = 0xfdb80 (c00fdb80) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xdba1
pnpbios: Found PnP BIOS data at 0xc00f4500
pnpbios: Entry = f0000:33a4 Rev = 1.0
Other BIOS signatures found:
x86bios: IVT 0x000000-0x0004ff at 0xc0000000
x86bios: SSEG 0x010000-0x01ffff at 0xc43b9000
x86bios: EBDA 0x09f000-0x09ffff at 0xc009f000
x86bios: ROM 0x0a0000-0x0effff at 0xc00a0000
ULE: setup cpu 0
ACPI: RSDP 0xff900 00014 (v00 AMI )
ACPI: RSDT 0x3fff0000 0002C (v01 RCC GCHE 00000001 MSFT 01000000)
ACPI: FACP 0x3fff0030 00074 (v01 RCC GCHE 00000001 MSFT 01000000)
ACPI: DSDT 0x3fff0150 049F1 (v01 RCC GCSL 00000100 MSFT 0100000D)
ACPI: FACS 0x3ffff000 00040
ACPI: APIC 0x3fff00b0 0009A (v01 RCC GCHE 00000001 MSFT 01000000)
MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
MADT: Found IO APIC ID 9, Interrupt 16 at 0xfec01000
MADT: Found IO APIC ID 10, Interrupt 32 at 0xfec02000
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0: intpin 9 polarity: low
ioapic0: intpin 9 trigger: level
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
ioapic2 <Version 1.1> irqs 32-47 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
acpi0: <RCC GCHE> on motherboard
ACPI Warning: Type override - [DEB_] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [MLIB] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [IO__] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [DATA] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [ICNT] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [ACPI] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [IORG] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [SB__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [SIO_] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [PM__] had invalid type (String) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [BIOS] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [CMOS] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [KBC_] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ACPI Warning: Type override - [OEM_] had invalid type (Integer) for Scope operator, changed to type ANY
(20101013/dswload-808)
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xc43b6000 pa 0x1000
pci_open(1): mode 1 addr port (0x0cf8) is 0x800078ac
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00171166)
pcibios: BIOS version 2.10
unknown: I/O range not supported
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 3ff00000 (3) failed
ACPI timer: 0/3 1/2 1/2 0/3 0/3 0/3 1/2 0/3 0/3 0/3 -> 3
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link8: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link9: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link10: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link11: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link12: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link13: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link14: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link15: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link16: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link17: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link18: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link19: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link20: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link21: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link22: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link23: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link24: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link25: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link26: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link27: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link28: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link29: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link30: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link31: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 11 12 14 15
pci_link32: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 10
Validation 0 10 N 0 10
After Disable 0 255 N 0 10
pci_link33: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 11
Validation 0 255 N 0 11
After Disable 0 255 N 0 11
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.15.INTA at func 2: 10
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x1166, dev=0x0017, revid=0x32
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0017, revid=0x00
domain=0, bus=0, slot=0, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1026, revid=0x04
domain=0, bus=0, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 64, base 0xfeb60000, size 17, enabled
map[18]: type Memory, range 64, base 0xfeb00000, size 18, enabled
map[20]: type I/O Port, range 32, base 0xe000, size 6, enabled
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
found-> vendor=0x1002, dev=0x4752, revid=0x27
domain=0, bus=0, slot=6, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xfd000000, size 24, enabled
map[14]: type I/O Port, range 32, base 0xe800, size 8, enabled
map[18]: type Memory, range 32, base 0xfebff000, size 12, enabled
pcib0: matched entry for 0.6.INTA
pcib0: slot 6 INTA hardwired to IRQ 26
found-> vendor=0x8086, dev=0x1229, revid=0x10
domain=0, bus=0, slot=7, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xfebfd000, size 12, enabled
map[14]: type I/O Port, range 32, base 0xe400, size 6, enabled
map[18]: type Memory, range 32, base 0xfeb80000, size 17, enabled
pcib0: matched entry for 0.7.INTA
pcib0: slot 7 INTA hardwired to IRQ 27
found-> vendor=0x14e4, dev=0x16a6, revid=0x02
domain=0, bus=0, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
map[10]: type Memory, range 64, base 0xfebe0000, size 16, enabled
pcib0: matched entry for 0.8.INTA
pcib0: slot 8 INTA hardwired to IRQ 28
found-> vendor=0x1166, dev=0x0203, revid=0xa0
domain=0, bus=0, slot=15, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x2200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0213, revid=0xa0
domain=0, bus=0, slot=15, func=1
class=01-01-8a, hdrtype=0x00, mfdev=1
cmdreg=0x0015, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type I/O Port, range 32, base 0xffa0, size 4, enabled
found-> vendor=0x1166, dev=0x0221, revid=0x05
domain=0, bus=0, slot=15, func=2
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=a, irq=10
map[10]: type Memory, range 32, base 0xfebfe000, size 12, enabled
pcib0: matched entry for 0.15.INTA (src \\_SB_.LNUS:0)
ioapic0: Changing trigger for pin 10 to level
ioapic0: Changing polarity for pin 10 to low
pcib0: slot 15 INTA routed to irq 10 via \\_SB_.LNUS
unknown: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfe000
ohci early: SMM active, request owner change
found-> vendor=0x1166, dev=0x0227, revid=0x00
domain=0, bus=0, slot=15, func=3
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
em0: <Intel(R) PRO/1000 Legacy Network Connection 1.0.4> port 0xe000-0xe03f mem 0xfeb60000-0xfeb7ffff,0xfeb00000-0xfeb3ffff irq 16 at device 1.0 on pci0
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfeb60000
em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0xe000
ioapic1: routing intpin 0 (PCI IRQ 16) to lapic 0 vector 49
em0: [FILTER]
em0: bpf attached
em0: Ethernet address: 00:04:23:df:fa:46
vgapci0: <VGA-compatible display> port 0xe800-0xe8ff mem 0xfd000000-0xfdffffff,0xfebff000-0xfebfffff irq 26 at device 6.0 on pci0
fxp0: <Intel 82551 Pro/100 Ethernet> port 0xe400-0xe43f mem 0xfebfd000-0xfebfdfff,0xfeb80000-0xfeb9ffff irq 27 at device 7.0 on pci0
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfd000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 8086 1050 0010
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
fxp0: bpf attached
fxp0: Ethernet address: 00:30:48:52:51:ae
ioapic1: routing intpin 11 (PCI IRQ 27) to lapic 0 vector 50
fxp0: [MPSAFE]
fxp0: [ITHREAD]
pci0:0:8:0: bad VPD cksum, remain 14
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x001002> mem 0xfebe0000-0xfebeffff irq 28 at device 8.0 on pci0
bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfebe0000
bge0: CHIP ID 0x00001002; ASIC REV 0x01; CHIP REV 0x10; PCI
miibus1: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy0: OUI 0x000818, model 0x0016, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: bpf attached
bge0: Ethernet address: 00:30:48:52:51:af
ioapic1: routing intpin 12 (PCI IRQ 28) to lapic 0 vector 51
bge0: [MPSAFE]
bge0: [ITHREAD]
atapci0: <ServerWorks CSB6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 15.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
ata0: <ATA channel> at channel 0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 52
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel> at channel 1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=01 ostat0=50 ostat1=ff
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0x10000
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 53
ata1: [MPSAFE]
ata1: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfebfe000-0xfebfefff irq 10 at device 15.2 on pci0
ohci0: (New OHCI DeviceId=0x02211166)
ioapic0: routing intpin 10 (ISA IRQ 10) to lapic 0 vector 54
ohci0: [MPSAFE]
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
usbus0: bpf attached
ohci0: usbpf: Attached
isab0: <PCI-ISA bridge> at device 15.3 on pci0
isa0: <ISA bus> on isab0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 55
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 56
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f3,0x3f4-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 73
ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 0 vector 57
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 58
uart0: [FILTER]
uart0: fast interrupt
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 0 vector 59
uart1: [FILTER]
uart1: fast interrupt
ppc0: using extended I/O port range
ppc0: SPP ECP
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 60
ppc0: [MPSAFE]
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
plip0: [MPSAFE]
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [MPSAFE]
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 0: ioport 0xc00 alloc failed
ex_isa_identify()
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
pmtimer0 on isa0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
uart: uart0 already exists; skipping it
uart: uart1 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
isa_probe_children: probing PnP devices
p4tcc0: <CPU Frequency Thermal Control> on cpu0
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 66669589 Hz
Timecounter "TSC" frequency 2666782592 Hz quality 800
Timecounters tick every 1.000 msec
vlan: initialized, using hash tables with chaining
ipfw2 (+ipv6) initialized, divert enabled, nat loadable, rule-based forwarding disabled, default to accept, logging disabled
ipfw0: bpf attached
lo0: bpf attached
hptrr: no controller detected.
ata0: Identifying devices: 00000001
ata0: New devices: 00000001
usbus0: 12Mbps Full Speed USB v1.0
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting UDMA100
ad0: 152627MB <WDC WD1600LB-55EDA0 15.05R15> at ata0-master UDMA100
ad0: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
ugen0.1: <0x1166> at usbus0
uhub0: <0x1166 OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1: Identifying devices: 00010000
ata1: New devices: 00010000
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting UDMA33
acd0: <MATSHITA CR-177/7T0D> CDROM drive at ata1 as master
acd0: read 4125KB/s (4125KB/s), 128KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ATA PseudoRAID loaded
uhub0: 4 ports with 4 removable, self powered
GEOM: new disk ad0
GEOM: ad0s2: geometry does not match label (255h,63s != 16h,63s).
Trying to mount root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
em0: Link is up 1000 Mbps Full Duplex
em0: Link is Down
em0: Link is up 1000 Mbps Full Duplex
splash: image decoder found: daemon_saver
More information about the freebsd-stable
mailing list