bug with some em nics on RELENG_7
Mike Tancsa
mike at sentex.net
Thu Nov 19 16:58:50 UTC 2009
At 07:29 PM 11/18/2009, Jack Vogel wrote:
>Hey Mike,
>
>Can you check if you see the same behavior on RELENG 8?
For RELENG_8. I installed an fxp card and netbooted off it.
I assigned an IP address to the onboard nic (em5). Pinged itself, got
a MAC and response. Plugged in the cable, pinged the other side, all ok
Did the same, but pinged the other side, and plugged the cable in,
all worked as expected.
# ping 10.177.194.18
PING 10.177.194.18 (10.177.194.18): 56 data bytes
ping: sendto: Host is down
ping: sendto: Host is down
ping: sendto: Host is down
64 bytes from 10.177.194.18: icmp_seq=30 ttl=64 time=1329.918 ms
64 bytes from 10.177.194.18: icmp_seq=31 ttl=64 time=324.925 ms
64 bytes from 10.177.194.18: icmp_seq=32 ttl=64 time=0.054 ms
64 bytes from 10.177.194.18: icmp_seq=33 ttl=64 time=0.055 ms
64 bytes from 10.177.194.18: icmp_seq=34 ttl=64 time=0.047 ms
64 bytes from 10.177.194.18: icmp_seq=35 ttl=64 time=0.050 ms
64 bytes from 10.177.194.18: icmp_seq=36 ttl=64 time=0.047 ms
64 bytes from 10.177.194.18: icmp_seq=37 ttl=64 time=0.049 ms
64 bytes from 10.177.194.18: icmp_seq=38 ttl=64 time=0.043 ms
em4: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xcc00-0xcc1f
mem 0xfaee0000-0xfaefffff,0xfaedc000-0xfaedffff irq 16 at device 0.0 on pci6
em4: Using MSIX interrupts
em4: [ITHREAD]
em4: [ITHREAD]
em4: [ITHREAD]
em4: Ethernet address: 00:30:48:d6:ef:12
pcib7: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci7: <ACPI PCI bus> on pcib7
em5: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xdc00-0xdc1f
mem 0xfafe0000-0xfaffffff,0xfafdc000-0xfafdffff irq 17 at device 0.0 on pci7
em5: Using MSIX interrupts
em5: [ITHREAD]
em5: [ITHREAD]
em5: [ITHREAD]
em5: Ethernet address: 00:30:48:d6:ef:13
So the problem is _not_ there under RELENG_8. I also tested the 2
PCIe nics to make sure they are still working, and they are.
Full dmesg below
opyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RC2 #0: Wed Nov 11 09:54:52 EST 2009
mdtancsa at ich10.sentex.ca:/usr/obj/usr/src/sys/alix i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz (2660.00-MHz
686-class CPU)
Origin = "GenuineIntel" Id = 0x106a5 Stepping = 5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x98e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT>
AMD Features=0x28100000<NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 6446645248 (6148 MB)
avail memory = 3137355776 (2992 MB)
ACPI APIC Table: <011209 APIC2037>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 2
cpu2 (AP): APIC ID: 4
cpu3 (AP): APIC ID: 6
ioapic0: Changing APIC ID to 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
acpi0: <011209 XSDT2037> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, bff00000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xac00-0xac1f
mem 0xface0000-0xfacfffff,0xfacc0000-0xfacdffff irq 16 at device 0.0 on pci1
em0: Using MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:15:17:78:e6:e0
em1: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xa880-0xa89f
mem 0xfac80000-0xfac9ffff,0xfac60000-0xfac7ffff irq 17 at device 0.1 on pci1
em1: Using MSI interrupt
em1: [FILTER]
em1: Ethernet address: 00:15:17:78:e6:e1
pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pci3: <ACPI PCI bus> on pcib3
em2: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xbc00-0xbc1f
mem 0xfade0000-0xfadfffff,0xfadc0000-0xfaddffff irq 16 at device 0.0 on pci3
em2: Using MSI interrupt
em2: [FILTER]
em2: Ethernet address: 00:15:17:cf:26:de
em3: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xb880-0xb89f
mem 0xfad80000-0xfad9ffff,0xfad60000-0xfad7ffff irq 17 at device 0.1 on pci3
em3: Using MSI interrupt
em3: [FILTER]
em3: Ethernet address: 00:15:17:cf:26:df
pcib4: <ACPI PCI-PCI bridge> at device 7.0 on pci0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 9.0 on pci0
pci5: <ACPI PCI bus> on pcib5
pci0: <base peripheral, interrupt controller> at device 16.0 (no
driver attached)
pci0: <base peripheral, interrupt controller> at device 16.1 (no
driver attached)
pci0: <base peripheral, interrupt controller> at device 20.0 (no
driver attached)
pci0: <base peripheral, interrupt controller> at device 20.1 (no
driver attached)
pci0: <base peripheral, interrupt controller> at device 20.2 (no
driver attached)
pci0: <base peripheral, interrupt controller> at device 20.3 (no
driver attached)
pci0: <base peripheral> at device 22.0 (no driver attached)
pci0: <base peripheral> at device 22.1 (no driver attached)
pci0: <base peripheral> at device 22.2 (no driver attached)
pci0: <base peripheral> at device 22.3 (no driver attached)
pci0: <base peripheral> at device 22.4 (no driver attached)
pci0: <base peripheral> at device 22.5 (no driver attached)
pci0: <base peripheral> at device 22.6 (no driver attached)
pci0: <base peripheral> at device 22.7 (no driver attached)
uhci0: <UHCI (generic) USB controller> port 0x9c00-0x9c1f irq 16 at
device 26.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x2f00
usbus0: <UHCI (generic) USB controller> on uhci0
uhci1: <UHCI (generic) USB controller> port 0x9880-0x989f irq 21 at
device 26.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x2f00
usbus1: <UHCI (generic) USB controller> on uhci1
uhci2: <UHCI (generic) USB controller> port 0x9800-0x981f irq 19 at
device 26.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x2f00
usbus2: <UHCI (generic) USB controller> on uhci2
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfabde000-0xfabde3ff
irq 18 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <EHCI (generic) USB 2.0 controller> on ehci0
pcib6: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci6: <ACPI PCI bus> on pcib6
em4: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xcc00-0xcc1f
mem 0xfaee0000-0xfaefffff,0xfaedc000-0xfaedffff irq 16 at device 0.0 on pci6
em4: Using MSIX interrupts
em4: [ITHREAD]
em4: [ITHREAD]
em4: [ITHREAD]
em4: Ethernet address: 00:30:48:d6:ef:12
pcib7: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci7: <ACPI PCI bus> on pcib7
em5: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xdc00-0xdc1f
mem 0xfafe0000-0xfaffffff,0xfafdc000-0xfafdffff irq 17 at device 0.0 on pci7
em5: Using MSIX interrupts
em5: [ITHREAD]
em5: [ITHREAD]
em5: [ITHREAD]
em5: Ethernet address: 00:30:48:d6:ef:13
uhci3: <UHCI (generic) USB controller> port 0x9480-0x949f irq 23 at
device 29.0 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x2f00
usbus4: <UHCI (generic) USB controller> on uhci3
uhci4: <UHCI (generic) USB controller> port 0x9400-0x941f irq 19 at
device 29.1 on pci0
uhci4: [ITHREAD]
uhci4: LegSup = 0x2f00
usbus5: <UHCI (generic) USB controller> on uhci4
uhci5: <UHCI (generic) USB controller> port 0x9080-0x909f irq 18 at
device 29.2 on pci0
uhci5: [ITHREAD]
uhci5: LegSup = 0x2f00
usbus6: <UHCI (generic) USB controller> on uhci5
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfabdc000-0xfabdc3ff
irq 23 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <EHCI (generic) USB 2.0 controller> on ehci1
pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci8: <ACPI PCI bus> on pcib8
fxp0: <Intel 82550 Pro/100 Ethernet> port 0xec00-0xec3f mem
0xfbefe000-0xfbefefff,0xfbec0000-0xfbedffff irq 17 at device 1.0 on pci8
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:02:b3:5d:ca:ce
fxp0: [ITHREAD]
vgapci0: <VGA-compatible display> mem
0xf9800000-0xf9ffffff,0xfbef8000-0xfbefbfff,0xfb000000-0xfb7fffff irq
17 at device 4.0 on pci8
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH10 SATA300 controller> port
0x9000-0x9007,0x8c00-0x8c03,0x8880-0x8887,0x8800-0x8803,0x8480-0x848f,0x8400-0x840f
irq 19 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci1: <Intel ICH10 SATA300 controller> port
0x8000-0x8007,0x7c00-0x7c03,0x7880-0x7887,0x7800-0x7803,0x7480-0x748f,0x7400-0x740f
irq 19 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci1
ata5: [ITHREAD]
acpi_button0: <Power Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart0: console (38400,n,8,1)
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
uart2: <16550 or compatible> port 0x3e8-0x3ef irq 5 on acpi0
uart2: [FILTER]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
cpu0: <ACPI CPU> on acpi0
ACPI Warning: Incorrect checksum in table [OEMB] - 8A, should be 87
20090521 tbutils-275
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 14
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 14
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
cpu2: <ACPI CPU> on acpi0
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 14
device_attach: est2 attach returned 6
p4tcc2: <CPU Frequency Thermal Control> on cpu2
cpu3: <ACPI CPU> on acpi0
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 14
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff
pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
ugen1.1: <Intel> at usbus1ugen0.1: <Intel> at usbus0Root mount
waiting for:ugen2.1: <Intel> at usbus2
usbus7 usbus6 usbus5 usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen3.1: <Intel> at usbus3uhub1:
<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4ugen5.1: <Intel> at usbus5ugen7.1: <Intel>
at usbus7ugen6.1: <Intel> at usbus6
uhub4:
<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
uhub5:
<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
Root mount waiting for: usbus7 usbus3
Root mount waiting for: usbus7 usbus3
uhub3: 6 ports with 6 removable, self powered
uhub7: 6 ports with 6 removable, self powered
Trying to mount root from nfs:10.255.255.1:/home/pxe
NFS ROOT: 10.255.255.1:/usr/home/pxe/
---Mike
--------------------------------------------------------------------
Mike Tancsa, tel +1 519 651 3400
Sentex Communications, mike at sentex.net
Providing Internet since 1994 www.sentex.net
Cambridge, Ontario Canada www.sentex.net/mike
More information about the freebsd-stable
mailing list