Dual Opteron system will not run SMP
Pete French
petefrench at ticketswitch.com
Mon Jun 5 14:24:06 UTC 2006
Not that 6.1 is out the dor I monder if anyone wuld like to give me
a hand with an SMP problem I have. I am running a system with two
Opterorn 242 processors in a K8D Master-F motherboard, each with 512M
of RAM attached. The processors both work and the system will run SMP
under wndows 2000 quite happily.
Under FreeBSD 61. the system also runs quite happily single processor,
but when I ruun an SMP kenel it freezes at the 'Waiting for SCSI devices
to settle; part of the boot process. Interesting it also does this in
single processor mode unless I have 'debug.acpi.disabled=timer'.
The motherboard has three plugin caards on it - an fxp Intel
either card, a Compaq 5402 RADI controller and an Adaptec 29160 which
is the boot device. In case these were causing problems I have also tried
unplugging all these cards are booting off an IDE drive. This exhibits
the same effect.
I *can* boot an SMP kene in 'safe mode' but this then only recognises
a single processor. I am using the GENERIC and SMP kerenls with no
modifications.
Other people have reported this motherboard to work. The output from
mptable is attached below if anyone is interested in trying to help
me track this down!
cheers,
-pcf.
skerry# mptable
===============================================================================
MPTable
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000ff780
signature: '_MP_'
length: 16 bytes
version: 1.1
checksum: 0xf1
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000fa300
signature: 'PCMP'
base table length: 324
version: 1.1
checksum: 0xb0
OEM ID: 'MSI '
Product ID: 'RHAPSODY '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 32
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x10 BSP, usable 15 5 1 0x78bfbff
1 0x10 AP, usable 15 5 1 0x78bfbff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 PCI
3 PCI
4 ISA
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
3 0x11 usable 0xfebfe000
4 0x11 usable 0xfebff000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 4 0 2 0
INT active-hi edge 4 1 2 1
INT active-hi edge 4 0 2 2
INT active-hi edge 4 3 2 3
INT active-hi edge 4 4 2 4
INT active-hi edge 4 6 2 6
INT active-hi edge 4 7 2 7
INT active-hi edge 4 8 2 8
INT active-hi edge 4 12 2 12
INT active-hi edge 4 13 2 13
INT active-hi edge 4 14 2 14
INT active-hi edge 4 15 2 15
INT active-lo level 0 7:D 2 19
INT active-lo level 3 0:D 2 19
INT active-lo level 3 8:A 2 16
INT active-lo level 3 6:A 2 18
INT active-lo level 2 3:A 3 0
INT active-lo level 1 1:A 4 0
INT active-lo level 1 2:A 4 1
INT active-lo level 1 2:B 4 2
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 0 0:A 255 0
NMI active-hi edge 0 0:A 255 1
===============================================================================
More information about the freebsd-stable
mailing list