ath0: ath_chan_set: unable to reset channel 5 (2432 Mhz, flags 0x3e0 hal flags 0x140)

[Douglas Berry]

Dlink DWL-AG530 can't scan, can't connect.
ifconfig ath0 up ; ifconfig ath0 list scan
returns nothing. On the same machine, same 'net, a different ath
card works (TRENDnet TEW-503PI).

Does anyone have this Dlink card working on RELENG_6?

pciconf output:
ath0 at pci0:14:0: class=0x020000 card=0x3a141186 chip=0x0013168c rev=0x01 hdr=0x00

dmesg snippet:
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
pci0: driver added
found-> vendor=0x1106, dev=0x3057, revid=0x40
        bus=0, slot=7, func=4
        class=06-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        powerspec 2  supports D0 D3  current D0
pci0:7:4: reprobing on driver added
found-> vendor=0x1106, dev=0x3058, revid=0x50
        bus=0, slot=7, func=5
        class=04-01-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0001, statreg=0x0210, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=5
        powerspec 2  supports D0 D3  current D0
pci0:7:5: reprobing on driver added
found-> vendor=0x168c, dev=0x0013, revid=0x01
        bus=0, slot=14, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x1c (7000 ns)
        intpin=a, irq=15
        powerspec 2  supports D0 D3  current D0
pci0:14:0: reprobing on driver added
ath0: <Atheros 5212> mem 0xe5810000-0xe581ffff irq 15 at device 14.0 on pci0
ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xe5810000
ath0: [MPSAFE]
ath0: bpf attached
ath0: Ethernet address: 00:11:95:ff:fe:f0
ath0: bpf attached
ath0: bpf attached
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 5.9 phy 4.3 radio 3.6
ath0: Use hw queue 1 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons
pci1: driver added
found-> vendor=0x1023, dev=0x8500, revid=0x6a
        bus=1, slot=0, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=255
        powerspec 1  supports D0 D1 D2 D3  current D0
pci1:0:0: reprobing on driver added
ath0: ath_chan_set: unable to reset channel 5 (2432 Mhz, flags 0x3e0 hal flags 0x140)

Thanks for tips,
doug