[sun] Booting problem with Sun Enterprise 220R

Fri May 11 06:09:08 UTC 2007

Well, if you can get it loose and boot on some other disk, that will
help. Until I get time on a system with a 10160, it's broken.

On 5/10/07, Ronan Kerambrun <ron at artful.net> wrote:
> Hi Matthew,
>
> nop I cant at time because the server is far away .. :)
> yes I think it is a PCI Card.
>
> Regards,
> Ronan Kerambrun
>
>
> Matthew Jacob a écrit :
> > Ouch. That means that it dies in register mapping. This chip is on a
> > PCI card? Can you pull it and install on another disk?
> >
> > On 5/9/07, ronan <ron at artful.net> wrote:
> >> Hi Matthew,
> >>
> >> I already have tried both but it dont work.
> >> load ispfw or set hint.isp.0.disable=1
> >>
> >> -------------------------------------------
> >> OK load ispfw
> >> OK boot
> >> nothing to autoload yet.
> >> jumping to kernel entry at 0xc0060000.
> >> stray vector interrupt 2029
> >> Copyright (c) 1992-2007 The FreeBSD Project.
> >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> >>        The Regents of the University of California. All rights reserved.
> >> FreeBSD is a registered trademark of The FreeBSD Foundation.
> >> FreeBSD 6.2-STABLE-200704 #0: Mon Apr  2 16:12:13 UTC 2007
> >> ...
> >> ...
> >> pci0: <serial bus, Fibre Channel> at device 2.0 (no driver attached)
> >> pcib1: <OFW PCI-PCI bridge> at device 4.0 on pci0
> >> pci1: <OFW PCI bus> on pcib1
> >> isp0: <Qlogic ISP 10160 PCI SCSI Adapter> port 0x1000-0x10ff mem
> >> 0x100000-0x100fff at device 4.0 on pci1
> >> isp0: [GIANT-LOCKED]
> >> panic: trap: data access error
> >> cpuid = 0
> >> Uptime: 1s
> >> Automatic reboot in 15 seconds - press a key on the console to abort
> >>
> >> ---------------------------------------------
> >>
> >> Do you think there is any way to use FreeBSD on this server ?
> >> Thank you for your help,
> >>
> >> Best regards,
> >> ronan.
> >>
> >>
> >> Matthew Jacob a écrit :
> >> > Yuck- this is the 10160 Ultra-160 part I've never actually seen. Does
> >> > the 6.2 bootonly iso have the ispfw module? That is, can you stup the
> >> > boot and do
> >> >
> >> > load ispfw
> >> >
> >> > and continue along and does that help? I suspect it probably doesn't
> >> > and I might h ave to do some work to get this supported. If your disks
> >> > are off of sym instead of isp, you can also do
> >> >
> >> > set hint.isp.0.disable=1
> >> >
> >> > so you can get installed at least.
> >> >
> >> > Let me know how this one goes.
> >> >
> >> > On 5/7/07, ronan <ron at artful.net> wrote:
> >> >> Hi all,
> >> >>
> >> >> I am trying to install from 6.2-STABLE-200704-sparc64-bootonly.iso
> >> >>
> >> <ftp://ftp.freebsd.org/pub/FreeBSD/snapshots/200704/6.2-STABLE-200704-sparc64-bootonly.iso>
> >>
> >> >>
> >> >> (it is the same from the 7.0 CURRENT snapshot)
> >> >> But I cant, it crash during booting the kernel. Here is the boot
> >> log :
> >> >>
> >> >>
> >> -------------------------------------------------------------------------
> >>
> >> >>
> >> >>
> >> >> Ethernet address 8:0:20:xx:xx:xx, Host ID: 80c823eb.
> >> >>
> >> >>
> >> >>
> >> >> Rebooting with command: boot /pci at 1f,4000/scsi at 3/disk at 6,0:f
> >> >> Boot device: /pci at 1f,4000/scsi at 3/disk at 6,0:f  File and args:
> >> >>
> >> >>  >> FreeBSD/sparc64 boot block
> >> >>   Boot path:   /pci at 1f,4000/scsi at 3/disk at 6,0:f
> >> >>   Boot loader: /boot/loader
> >> >> Consoles: Open Firmware console
> >> >> Boot path set to /pci at 1f,4000/scsi at 3/disk at 6,0:a
> >> >>
> >> >> FreeBSD/sparc64 bootstrap loader, Revision 1.0
> >> >> (root at edmunds.cse.buffalo.edu, Mon Apr  2 00:37:48 UTC 2007)
> >> >> bootpath="/pci at 1f,4000/scsi at 3/disk at 6,0:a"
> >> >> Loading /boot/defaults/loader.conf
> >> >> /boot/kernel/kernel data=0x56f408+0x5bfa8
> >> syms=[0x8+0x6d7b8+0x8+0x5b032]
> >> >> -
> >> >> Hit [Enter] to boot immediately, or any other key for command prompt.
> >> >> Booting [/boot/kernel/kernel]...
> >> >> nothing to autoload yet.
> >> >> jumping to kernel entry at 0xc0060000.
> >> >> stray vector interrupt 2029
> >> >> Copyright (c) 1992-2007 The FreeBSD Project.
> >> >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992,
> >> 1993, 1994
> >> >>        The Regents of the University of California. All rights
> >> reserved.
> >> >> FreeBSD is a registered trademark of The FreeBSD Foundation.
> >> >> FreeBSD 6.2-STABLE-200704 #0: Mon Apr  2 16:12:13 UTC 2007
> >> >>    root at edmunds.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
> >> >> real memory  = 2147483648 (2048 MB)
> >> >> avail memory = 2063147008 (1967 MB)
> >> >> cpu0: Sun Microsystems UltraSparc-II Processor (450.05 MHz CPU)
> >> >> cpu1: Sun Microsystems UltraSparc-II Processor (450.05 MHz CPU)
> >> >> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> >> >> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
> >> >> RF5413, REGOPS_FUNC)
> >> >> nexus0: <Open Firmware Nexus device>
> >> >> pcib0: <U2P UPA-PCI bridge> on nexus0
> >> >> pcib0: Psycho, impl 0, version 4, ign 0x7c0, bus B
> >> >> pcib0: [FAST]
> >> >> pcib0: [FAST]
> >> >> pcib0: [GIANT-LOCKED]
> >> >> pcib0: [GIANT-LOCKED]
> >> >> pcib0: [FAST]
> >> >> initializing counter-timer
> >> >> Timecounter "counter-timer" frequency 1000000 Hz quality 100
> >> >> pcib0 dvma: DVMA map: 0xfc000000 to 0xffffffff
> >> >> pci0: <OFW PCI bus> on pcib0
> >> >> ebus0: <PCI-EBus2 bridge> mem
> >> >> 0x70000000-0x70ffffff,0x71000000-0x717fffff at device 1.0 on pci0
> >> >> auxio0: <Sun Auxiliary I/O> addr
> >> >>
> >> 0x1400726000-0x1400726003,0x1400728000-0x1400728003,0x140072a000-0x140072a003,0x140072c000-0x140072c003,0x140072f000-0x140072f003
> >>
> >> >>
> >> >> on ebus0
> >> >> ebus0: <power> addr 0x1400724000-0x1400724003 (no driver attached)
> >> >> ebus0: <SUNW,pll> addr 0x1400504000-0x1400504002 (no driver attached)
> >> >> ebus0: <sc> addr 0x1400500000-0x1400500007 (no driver attached)
> >> >> puc0: <Siemens SAB 82532 dual channel SCC> addr
> >> >> 0x1400400000-0x140040007f irq 43 on ebus0
> >> >> uart0: <SAB 82532 v3.2, channel A> on puc0
> >> >> uart0: CTS oflow
> >> >> uart0: console (9600,n,8,1)
> >> >> uart1: <SAB 82532 v3.2, channel B> on puc0
> >> >> uart1: CTS oflow
> >> >> uart2: <16550 or compatible> addr 0x14003083f8-0x14003083ff irq 41 on
> >> >> ebus0
> >> >> uart2: keyboard (1200,n,8,1)
> >> >> uart2: keyboard not present
> >> >> uart3: <16550 or compatible> addr 0x14003062f8-0x14003062ff irq 42 on
> >> >> ebus0
> >> >> ebus0: <ecpp> addr
> >> >>
> >> 0x14003043bc-0x14003043cb,0x1400300398-0x1400300399,0x1400700000-0x140070000f
> >>
> >> >>
> >> >> irq 34 (no driver attached)
> >> >> ebus0: <fdthree> addr
> >> >>
> >> 0x14003023f0-0x14003023f7,0x1400706000-0x140070600f,0x1400720000-0x1400720003
> >>
> >> >>
> >> >> irq 39 (no driver attached)
> >> >> eeprom0: <EEPROM/clock> addr 0x1400000000-0x1400001fff on ebus0
> >> >> eeprom0: model mk48t59
> >> >> eeprom0: hostid 80c823eb
> >> >> ebus0: <flashprom> addr 0x1000000000-0x10000fffff (no driver
> >> attached)
> >> >> hme0: <Sun HME 10/100 Ethernet> mem 0x500000-0x507fff at device 1.1
> >> >> on pci0
> >> >> miibus0: <MII bus> on hme0
> >> >> ukphy0: <Generic IEEE 802.3u media interface> on miibus0
> >> >> ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> >> >> hme0: Ethernet address: 08:00:20:c8:23:eb
> >> >> sym0: <875> port 0x2000-0x20ff mem
> >> 0x508000-0x5080ff,0x50a000-0x50afff
> >> >> at device 3.0 on pci0
> >> >> sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
> >> >> sym0: [GIANT-LOCKED]
> >> >> sym1: <875> port 0x2400-0x24ff mem
> >> 0x50c000-0x50c0ff,0x50e000-0x50efff
> >> >> at device 3.1 on pci0
> >> >> sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
> >> >> sym1: [GIANT-LOCKED]
> >> >> pci0: <serial bus, Fibre Channel> at device 2.0 (no driver attached)
> >> >> pcib1: <OFW PCI-PCI bridge> at device 4.0 on pci0
> >> >> pci1: <OFW PCI bus> on pcib1
> >> >> isp0: <Qlogic ISP 10160 PCI SCSI Adapter> port 0x1000-0x10ff mem
> >> >> 0x100000-0x100fff at device 4.0 on pci1
> >> >> isp0: [GIANT-LOCKED]
> >> >> panic: trap: data access error
> >> >> cpuid = 0
> >> >> Uptime: 1s
> >> >> Automatic reboot in 15 seconds - press a key on the console to abort
> >> >>
> >> >>
> >> -------------------------------------------------------------------------
> >>
> >> >>
> >> >>
> >> >> Is there any solution ? Is it a compatibility problem with the Qlogic
> >> >> ISP 10160 ?
> >> >>
> >> >> Best regards,
> >> >>
> >> >> ronan.
> >> >>
> >> >> _______________________________________________
> >> >> freebsd-sparc64 at freebsd.org mailing list
> >> >> http://lists.freebsd.org/mailman/listinfo/freebsd-sparc64
> >> >> To unsubscribe, send any mail to
> >> >> "freebsd-sparc64-unsubscribe at freebsd.org"
> >> >>
> >> >
> >> >
> >> _______________________________________________
> >> freebsd-sparc64 at freebsd.org mailing list
> >> http://lists.freebsd.org/mailman/listinfo/freebsd-sparc64
> >> To unsubscribe, send any mail to
> >> "freebsd-sparc64-unsubscribe at freebsd.org"
> >>
> >
> >
>
> --
> -------------------------------------------------------------
> *Ronan Kerambrun*
> *Administrateur Systèmes / Réseaux*
>
> *Artful*
> 5 avenue des peupliers - 35510 Cesson Sévigné
> tél : +33 2 99 125 757 - fax : +33 2 99 125 758
> www.artful.net <http://www.artful.net>
>
> a claranet company <http://www.clara.net/>
>
> _______________________________________________
> freebsd-sparc64 at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-sparc64
> To unsubscribe, send any mail to "freebsd-sparc64-unsubscribe at freebsd.org"
>