Release 9.1 and 3G usb Modem

[Leonardo Santagostini]

Hello Odhiambo .

The 3G model is Huawei E173 with Movistar Argentina.

Ive tried but i cant see in windows de USB port to have a serial link :(

Saludos / Regards
Leonardo Santagostini





2013/3/27 Odhiambo Washington <odhiambo at gmail.com>

>
> On 27 March 2013 16:29, Leonardo Santagostini <lsantagostini at gmail.com>wrote:
>
>> Hello all.
>>
>> I have a latitude e6400 with FreeBSD Release 9.1. And i can't get the USB
>> modem working.
>>
>> I tried with umodem, u3g but no luck :(
>>
>
> [snip]
>
>
>> ugen7.2: <HUAWEI> at usbus7
>> ugen7.2: <HUAWEI> at usbus7 (disconnected)
>> ugen7.2: <HUAWEI> at usbus7
>> umodem0: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on
>> usbus7
>> umodem0: data interface 0, has no CM over data, has no break
>> umodem1: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on
>> usbus7
>> umodem1: data interface 1, has no CM over data, has no break
>> umodem2: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on
>> usbus7
>> umodem2: data interface 2, has no CM over data, has no break
>> umass0: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7
>> umass0:  SCSI over Bulk-Only; quirks = 0x0000
>> umass0:9:0:-1: Attached to scbus9
>> cd1 at umass-sim0 bus 0 scbus9 target 0 lun 0
>> cd1: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device
>> cd1: 40.000MB/s transfers
>> cd1: Attempt to query device size failed: NOT READY, Medium not present
>> umass1: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7
>> umass1:  SCSI over Bulk-Only; quirks = 0x0000
>> umass1:10:1:-1: Attached to scbus10
>> da0 at umass-sim1 bus 1 scbus10 target 0 lun 0
>> da0: <HUAWEI SD Storage 2.31> Removable Direct Access SCSI-2 device
>> da0: 40.000MB/s transfers
>> da0: Attempt to query device size failed: NOT READY, Medium not present
>>
>
>
> [snip]
>
> Huawei modem, as I can see. That should be easy.
>
> Connect to the modem through HyperTerminal or Putty on a different machine
> Issue the command: AT^U2DIAG=0
> That should disable the virtual CD-ROM and FreeBSD will see the modem.
>
> Here are some commands you'll need to know about:
> Do you have a Windows PC near you? If you plug the device into it and the
> virtualCD pops up, then it means command was not successful. The fact that
> fake CD still shows means command did not succeed!
>
> AT^u2diag=0 (all off)
> AT^u2diag=1 (CD on, SD off)
> AT^u2diag=256 (CD off, SD is on)
> AT^u2diag=255 (all on - including SD Card)
> AT^u2diag=276 (Factory Reset)
> A+CLAC - Display all available commands. However it does not tell you how
> to use them
>
>
>
> And here is a working ppp.conf - but you need to change the *bolded* values
> to match your end of the environment:)
>
> u3g:
>  set device */dev/cuaU0.0*
>  set server /var/run/3g-internet "" 0177
>  set speed 921600
>  set timeout 0
>  set authname *saf*
>  set authkey *data*
>  set dial "ABORT BUSY ABORT NO\\sTIMEOUT 2 \
>        \"\" \
>        AT OK-AT-OK \
>        AT+CFUN=1 OK-AT-OK \
>        AT+CMEE=2 OK-AT-OK \
>        AT+CSQ OK \
>        AT+CGDCONT=1,\\\"IP\\\",\\\"*APN*\\\" OK \
>        ATD**99#* CONNECT"
>  set crtscts on
>  disable vjcomp
>  disable acfcomp
>  disable deflate
>  disable deflate24
>  disable pred1
>  disable protocomp
>  disable mppe
>  disable ipv6cp
>  disable lqr
>  disable echo
>  #nat enable yes
>  enable dns
>  resolv writable
>  set dns 8.8.8.8
>  set ifaddr 10.1.0.2/0 10.1.0.1/0 255.255.255.255 0.0.0.0
>  add default HISADDR          # See ppp.link*
>
>
> Lemme know if you get stuck.
>
> Also, always give details about modem - manufacturer, model...
>
>
> --
> Best regards,
> Odhiambo WASHINGTON,
> Nairobi,KE
> +254733744121/+254722743223
> "I can't hear you -- I'm using the scrambler."
>