IPMI SoL oddity on 9.0
Ihsan Junaidi Ibrahim
ihsan.junaidi at gmail.com
Wed Jun 13 10:33:43 UTC 2012
I've managed to get SoL to work.
Turned out the IPMI is utilizing uart2 on my box so modified loader.conf so uart2 is configured to be the serial console port.
hint.uart.0.flags="0x0"
hint.uart.2.at="isa"
hint.uart.2.port="0x3E8"
hint.uart.2.irq="10"
hint.uart.2.flags="0x10"
The handbook does not seem to indicate this very clearly but well, now that it's working, I'm a happy man.
ihsan
On Jun 13, 2012, at 5:53 AM, Ihsan Junaidi Ibrahim wrote:
> Folks,
>
> I'm hitting a roadblock on getting IPMI SoL up and running on my Supermicro box. It's a X9SCL-F with a dedicated IPMI LAN.
>
> I've installed ipmitool and set the necessary console redirects (COM1, COM2 and SoL) in the BIOS. The new AMI BIOS does not seem to indicate the SoL is sharing resources with either one of the two COM ports. All 3 redirect speed is 9600.
>
> Serial console works, as far as COM ports are concerned. The BIOS, the boot, loader, kernel messages and TTY are all redirected to the COMs.
>
> However SoL only works with the BIOS, boot and reading loader defaults.
>
> It will get stuck once it enters the spinning kernel boot and it will stay there.
>
> I've tried playing with 0x10 uart flags in device.hints alternating between uart0 and uart1 also to no available in hoping that the SoL port is sharing with either one of the two COMs.
>
> Regardless SoL simply will not work entering the kernel onwards.
>
> Attached are what I believe the configs relevant to my problem.
>
> inf02-kul# cat /boot.config
> -P
>
> inf02-kul# cat /boot/loader.conf
> autoboot_delay="1"
> console="comconsole"
> boot_serial=""
> boot_multicons=""
>
> inf02-kul# grep uart /var/run/dmesg.boot
> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> uart0: console (9600,n,8,1)
> uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
> uart2: <16550 or compatible> port 0x3e8-0x3ef irq 10 on acpi0
>
> inf02-kul# grep ttyu /etc/ttys
> ttyu0 "/usr/libexec/getty std.9600" vt100 on secure
> ttyu1 "/usr/libexec/getty std.9600" vt100 on secure
> ttyu2 "/usr/libexec/getty std.9600" vt100 on secure
> ttyu3 "/usr/libexec/getty std.9600" dialup off secure
>
> inf02-kul# ipmitool sol info
> Set in progress : set-complete
> Enabled : true
> Force Encryption : false
> Force Authentication : false
> Privilege Level : USER
> Character Accumulate Level (ms) : 5
> Character Send Threshold : 1
> Retry Count : 0
> Retry Interval (ms) : 0
> Volatile Bit Rate (kbps) : 9.6
> Non-Volatile Bit Rate (kbps) : 9.6
> Payload Channel : 1 (0x01)
> Payload Port : 623
>
> inf02-kul# cat /var/run/dmesg.boot
> Copyright (c) 1992-2012 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 9.0-RELEASE-p3 #0: Tue Jun 12 02:52:29 UTC 2012
> root at amd64-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC amd64
> CPU: Intel(R) Xeon(R) CPU E3-1230 V2 @ 3.30GHz (3292.59-MHz K8-class CPU)
> Origin = "GenuineIntel" Id = 0x306a9 Family = 6 Model = 3a Stepping = 9
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Features2=0x77bae3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,AESNI,XSAVE,AVX,F16C,<b30>>
> AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
> AMD Features2=0x1<LAHF>
> TSC: P-state invariant, performance statistics
> real memory = 8589934592 (8192 MB)
> avail memory = 8219156480 (7838 MB)
> Event timer "LAPIC" quality 600
> ACPI APIC Table: <SUPERM SMCI--MB>
> FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
> FreeBSD/SMP: 1 package(s) x 4 core(s) x 2 SMT threads
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> cpu2 (AP): APIC ID: 2
> cpu3 (AP): APIC ID: 3
> cpu4 (AP): APIC ID: 4
> cpu5 (AP): APIC ID: 5
> cpu6 (AP): APIC ID: 6
> cpu7 (AP): APIC ID: 7
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> acpi0: <SUPERM SMCI--MB> on motherboard
> acpi0: Power Button (fixed)
> acpi0: reservation of 67, 1 (4) failed
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
> cpu0: <ACPI CPU> on acpi0
> cpu1: <ACPI CPU> on acpi0
> cpu2: <ACPI CPU> on acpi0
> cpu3: <ACPI CPU> on acpi0
> cpu4: <ACPI CPU> on acpi0
> cpu5: <ACPI CPU> on acpi0
> cpu6: <ACPI CPU> on acpi0
> cpu7: <ACPI CPU> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> pcib2: <ACPI PCI-PCI bridge> irq 16 at device 1.1 on pci0
> pci2: <ACPI PCI bus> on pcib2
> igb0: <Intel(R) PRO/1000 Network Connection version - 2.2.5> port 0xe020-0xe03f mem 0xf7a20000-0xf7a3ffff,0xf7800000-0xf79fffff,0xf7a44000-0xf7a47fff irq 17 at device 0.0 on pci2
> igb0: Using MSIX interrupts with 5 vectors
> igb0: Ethernet address: 00:25:90:6c:25:00
> igb1: <Intel(R) PRO/1000 Network Connection version - 2.2.5> port 0xe000-0xe01f mem 0xf7a00000-0xf7a1ffff,0xf7400000-0xf75fffff,0xf7a40000-0xf7a43fff irq 18 at device 0.1 on pci2
> igb1: Using MSIX interrupts with 5 vectors
> igb1: Ethernet address: 00:25:90:6c:25:01
> em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xf020-0xf03f mem 0xf7100000-0xf711ffff,0xf7125000-0xf7125fff irq 20 at device 25.0 on pci0
> em0: Using an MSI interrupt
> em0: Setup of Shared code failed
> device_attach: em0 attach returned 6
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7124000-0xf71243ff irq 16 at device 26.0 on pci0
> usbus0: EHCI version 1.0
> usbus0: <EHCI (generic) USB 2.0 controller> on ehci0
> pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pci3: <ACPI PCI bus> on pcib3
> pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
> pci4: <ACPI PCI bus> on pcib4
> em1: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xd000-0xd01f mem 0xf7c00000-0xf7c1ffff,0xf7c20000-0xf7c23fff irq 16 at device 0.0 on pci4
> em1: Using MSIX interrupts with 3 vectors
> em1: Ethernet address: 00:25:90:77:35:08
> ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf7123000-0xf71233ff irq 23 at device 29.0 on pci0
> usbus1: EHCI version 1.0
> usbus1: <EHCI (generic) USB 2.0 controller> on ehci1
> pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci5: <ACPI PCI bus> on pcib5
> vgapci0: <VGA-compatible display> mem 0xf5000000-0xf5ffffff,0xf7000000-0xf7003fff,0xf6800000-0xf6ffffff irq 19 at device 3.0 on pci5
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> ahci0: <Intel Cougar Point AHCI SATA controller> port 0xf070-0xf077,0xf060-0xf063,0xf050-0xf057,0xf040-0xf043,0xf000-0xf01f mem 0xf7122000-0xf71227ff irq 19 at device 31.2 on pci0
> ahci0: AHCI v1.30 with 6 3Gbps ports, Port Multiplier not supported
> ahcich0: <AHCI channel> at channel 0 on ahci0
> ahcich1: <AHCI channel> at channel 1 on ahci0
> ahcich2: <AHCI channel> at channel 2 on ahci0
> ahcich3: <AHCI channel> at channel 3 on ahci0
> ahcich4: <AHCI channel> at channel 4 on ahci0
> ahcich5: <AHCI channel> at channel 5 on ahci0
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> acpi_button0: <Power Button> on acpi0
> acpi_tz0: <Thermal Zone> on acpi0
> acpi_tz1: <Thermal Zone> on acpi0
> hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> Timecounter "HPET" frequency 14318180 Hz quality 950
> Event timer "HPET" frequency 14318180 Hz quality 550
> atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
> atrtc0: Warning: Couldn't map I/O.
> Event timer "RTC" frequency 32768 Hz quality 0
> attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Event timer "i8254" frequency 1193182 Hz quality 100
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> uart0: console (9600,n,8,1)
> uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
> uart2: <16550 or compatible> port 0x3e8-0x3ef irq 10 on acpi0
> ipmi0: <IPMI System Interface> port 0xca2,0xca3 on acpi0
> ipmi0: KCS mode found at io 0xca2 on acpi
> ipmi1: <IPMI System Interface> on isa0
> device_attach: ipmi1 attach returned 16
> ipmi1: <IPMI System Interface> on isa0
> device_attach: ipmi1 attach returned 16
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> ppc0: cannot reserve I/O port range
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> est1: <Enhanced SpeedStep Frequency Control> on cpu1
> p4tcc1: <CPU Frequency Thermal Control> on cpu1
> est2: <Enhanced SpeedStep Frequency Control> on cpu2
> p4tcc2: <CPU Frequency Thermal Control> on cpu2
> est3: <Enhanced SpeedStep Frequency Control> on cpu3
> p4tcc3: <CPU Frequency Thermal Control> on cpu3
> est4: <Enhanced SpeedStep Frequency Control> on cpu4
> p4tcc4: <CPU Frequency Thermal Control> on cpu4
> est5: <Enhanced SpeedStep Frequency Control> on cpu5
> p4tcc5: <CPU Frequency Thermal Control> on cpu5
> est6: <Enhanced SpeedStep Frequency Control> on cpu6
> p4tcc6: <CPU Frequency Thermal Control> on cpu6
> est7: <Enhanced SpeedStep Frequency Control> on cpu7
> p4tcc7: <CPU Frequency Thermal Control> on cpu7
> Timecounters tick every 1.000 msec
> usbus0: 480Mbps High Speed USB v2.0
> usbus1: 480Mbps High Speed USB v2.0
> ugen0.1: <Intel> at usbus0
> uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
> ipmi0: IPMI device rev. 1, firmware rev. 1.64, version 2.0
> ipmi0: Number of channels 2
> ipmi0: Attached watchdog
> ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
> ada0: <KINGSTON SVP200S360G 501ABBF0> ATA-8 SATA 3.x device
> ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada0: Command Queueing enabled
> ada0: 57241MB (117231408 512 byte sectors: 16H 63S/T 16383C)
> ada0: Previously was known as ad4
> ada1 at ahcich2 bus 0 scbus2 target 0 lun 0
> ada1: <WDC WD5003ABYX-01WERA1 01.01S02> ATA-8 SATA 2.x device
> ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada1: Command Queueing enabled
> ada1: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C)
> ada1: Previously was known as ad8
> SMP: AP CPU #1 Launched!
> SMP: AP CPU #6 Launched!
> SMP: AP CPU #5 Launched!
> SMP: AP CPU #4 Launched!
> SMP: AP CPU #7 Launched!
> SMP: AP CPU #2 Launched!
> SMP: AP CPU #3 Launched!
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> Root mount waiting for: usbus1 usbus0
> ugen0.2: <vendor 0x8087> at usbus0
> uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
> ugen1.2: <vendor 0x8087> at usbus1
> uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
> Root mount waiting for: usbus1 usbus0
> uhub2: 6 ports with 6 removable, self powered
> uhub3: 6 ports with 6 removable, self powered
> ugen0.3: <Winbond Electronics Corp> at usbus0
> ums0: <Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0, rev 1.10/0.01, addr 3> on usbus0
> ums0: 3 buttons and [Z] coordinates ID=0
> ukbd0: <Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0, rev 1.10/0.01, addr 3> on usbus0
> kbd2 at ukbd0
> Trying to mount root from ufs:/dev/ada0p2 [rw]...
More information about the freebsd-questions
mailing list