IPMI SoL oddity on 9.0
Ihsan Junaidi Ibrahim
ihsan.junaidi at gmail.com
Tue Jun 12 21:53:20 UTC 2012
Folks,
I'm hitting a roadblock on getting IPMI SoL up and running on my Supermicro box. It's a X9SCL-F with a dedicated IPMI LAN.
I've installed ipmitool and set the necessary console redirects (COM1, COM2 and SoL) in the BIOS. The new AMI BIOS does not seem to indicate the SoL is sharing resources with either one of the two COM ports. All 3 redirect speed is 9600.
Serial console works, as far as COM ports are concerned. The BIOS, the boot, loader, kernel messages and TTY are all redirected to the COMs.
However SoL only works with the BIOS, boot and reading loader defaults.
It will get stuck once it enters the spinning kernel boot and it will stay there.
I've tried playing with 0x10 uart flags in device.hints alternating between uart0 and uart1 also to no available in hoping that the SoL port is sharing with either one of the two COMs.
Regardless SoL simply will not work entering the kernel onwards.
Attached are what I believe the configs relevant to my problem.
inf02-kul# cat /boot.config
-P
inf02-kul# cat /boot/loader.conf
autoboot_delay="1"
console="comconsole"
boot_serial=""
boot_multicons=""
inf02-kul# grep uart /var/run/dmesg.boot
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart2: <16550 or compatible> port 0x3e8-0x3ef irq 10 on acpi0
inf02-kul# grep ttyu /etc/ttys
ttyu0 "/usr/libexec/getty std.9600" vt100 on secure
ttyu1 "/usr/libexec/getty std.9600" vt100 on secure
ttyu2 "/usr/libexec/getty std.9600" vt100 on secure
ttyu3 "/usr/libexec/getty std.9600" dialup off secure
inf02-kul# ipmitool sol info
Set in progress : set-complete
Enabled : true
Force Encryption : false
Force Authentication : false
Privilege Level : USER
Character Accumulate Level (ms) : 5
Character Send Threshold : 1
Retry Count : 0
Retry Interval (ms) : 0
Volatile Bit Rate (kbps) : 9.6
Non-Volatile Bit Rate (kbps) : 9.6
Payload Channel : 1 (0x01)
Payload Port : 623
inf02-kul# cat /var/run/dmesg.boot
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-RELEASE-p3 #0: Tue Jun 12 02:52:29 UTC 2012
root at amd64-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC amd64
CPU: Intel(R) Xeon(R) CPU E3-1230 V2 @ 3.30GHz (3292.59-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x306a9 Family = 6 Model = 3a Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x77bae3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,AESNI,XSAVE,AVX,F16C,<b30>>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 8219156480 (7838 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <SUPERM SMCI--MB>
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s) x 2 SMT threads
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 4
cpu5 (AP): APIC ID: 5
cpu6 (AP): APIC ID: 6
cpu7 (AP): APIC ID: 7
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <SUPERM SMCI--MB> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of 67, 1 (4) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 1.1 on pci0
pci2: <ACPI PCI bus> on pcib2
igb0: <Intel(R) PRO/1000 Network Connection version - 2.2.5> port 0xe020-0xe03f mem 0xf7a20000-0xf7a3ffff,0xf7800000-0xf79fffff,0xf7a44000-0xf7a47fff irq 17 at device 0.0 on pci2
igb0: Using MSIX interrupts with 5 vectors
igb0: Ethernet address: 00:25:90:6c:25:00
igb1: <Intel(R) PRO/1000 Network Connection version - 2.2.5> port 0xe000-0xe01f mem 0xf7a00000-0xf7a1ffff,0xf7400000-0xf75fffff,0xf7a40000-0xf7a43fff irq 18 at device 0.1 on pci2
igb1: Using MSIX interrupts with 5 vectors
igb1: Ethernet address: 00:25:90:6c:25:01
em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xf020-0xf03f mem 0xf7100000-0xf711ffff,0xf7125000-0xf7125fff irq 20 at device 25.0 on pci0
em0: Using an MSI interrupt
em0: Setup of Shared code failed
device_attach: em0 attach returned 6
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7124000-0xf71243ff irq 16 at device 26.0 on pci0
usbus0: EHCI version 1.0
usbus0: <EHCI (generic) USB 2.0 controller> on ehci0
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci4: <ACPI PCI bus> on pcib4
em1: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xd000-0xd01f mem 0xf7c00000-0xf7c1ffff,0xf7c20000-0xf7c23fff irq 16 at device 0.0 on pci4
em1: Using MSIX interrupts with 3 vectors
em1: Ethernet address: 00:25:90:77:35:08
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf7123000-0xf71233ff irq 23 at device 29.0 on pci0
usbus1: EHCI version 1.0
usbus1: <EHCI (generic) USB 2.0 controller> on ehci1
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
vgapci0: <VGA-compatible display> mem 0xf5000000-0xf5ffffff,0xf7000000-0xf7003fff,0xf6800000-0xf6ffffff irq 19 at device 3.0 on pci5
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci0: <Intel Cougar Point AHCI SATA controller> port 0xf070-0xf077,0xf060-0xf063,0xf050-0xf057,0xf040-0xf043,0xf000-0xf01f mem 0xf7122000-0xf71227ff irq 19 at device 31.2 on pci0
ahci0: AHCI v1.30 with 6 3Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich5: <AHCI channel> at channel 5 on ahci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart2: <16550 or compatible> port 0x3e8-0x3ef irq 10 on acpi0
ipmi0: <IPMI System Interface> port 0xca2,0xca3 on acpi0
ipmi0: KCS mode found at io 0xca2 on acpi
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
est4: <Enhanced SpeedStep Frequency Control> on cpu4
p4tcc4: <CPU Frequency Thermal Control> on cpu4
est5: <Enhanced SpeedStep Frequency Control> on cpu5
p4tcc5: <CPU Frequency Thermal Control> on cpu5
est6: <Enhanced SpeedStep Frequency Control> on cpu6
p4tcc6: <CPU Frequency Thermal Control> on cpu6
est7: <Enhanced SpeedStep Frequency Control> on cpu7
p4tcc7: <CPU Frequency Thermal Control> on cpu7
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ipmi0: IPMI device rev. 1, firmware rev. 1.64, version 2.0
ipmi0: Number of channels 2
ipmi0: Attached watchdog
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <KINGSTON SVP200S360G 501ABBF0> ATA-8 SATA 3.x device
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 57241MB (117231408 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
ada1 at ahcich2 bus 0 scbus2 target 0 lun 0
ada1: <WDC WD5003ABYX-01WERA1 01.01S02> ATA-8 SATA 2.x device
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad8
SMP: AP CPU #1 Launched!
SMP: AP CPU #6 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
Root mount waiting for: usbus1 usbus0
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
Root mount waiting for: usbus1 usbus0
uhub2: 6 ports with 6 removable, self powered
uhub3: 6 ports with 6 removable, self powered
ugen0.3: <Winbond Electronics Corp> at usbus0
ums0: <Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0, rev 1.10/0.01, addr 3> on usbus0
ums0: 3 buttons and [Z] coordinates ID=0
ukbd0: <Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0, rev 1.10/0.01, addr 3> on usbus0
kbd2 at ukbd0
Trying to mount root from ufs:/dev/ada0p2 [rw]...
More information about the freebsd-questions
mailing list