DHCP problem after upgrade

Thu Sep 23 06:09:13 UTC 2010

I upgraded my system from 7.2-STABLE to 8.1-STABLE, and have done
`mergemaster'.  Earlier the system used to get its IP address by DHCP
at boot time without any problem.  After the upgrade, it is not doing
so.  I have ifconfig_em0="DHCP" in /etc/rc.conf.  After booting,
manually doing `/sbin/dhclient em0' works.  The dmesg is enclosed
below.  Any help is appreciated.

Thanks and regards,
Raghavendra.

----------------------------------------------------------------------

Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-STABLE #0: Thu Sep 23 09:18:44 IST 2010
    root at griffin.campus.hri:/usr/obj/usr/src/sys/GRIFFIN i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Quad CPU    Q6600  @ 2.40GHz (2394.01-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6fb  Family = 6  Model = f  Stepping = 11
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 3221225472 (3072 MB)
avail memory = 3140222976 (2994 MB)
ACPI APIC Table: <DELL   FX09   >
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
 cpu2 (AP): APIC ID:  2
 cpu3 (AP): APIC ID:  3
ioapic0: Changing APIC ID to 4
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <DELL FX09   > on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, bfd90000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
device_attach: acpi_hpet0 attach returned 12
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xcf00-0xcf7f mem 0xfa000000-0xfaffffff,0xd0000000-0xdfffffff,0xf8000000-0xf9ffffff irq 16 at device 0.0 on pci1
em0: <Intel(R) PRO/1000 Network Connection 7.0.5> port 0xff00-0xff1f mem 0xfdfc0000-0xfdfdffff,0xfdfff000-0xfdffffff irq 20 at device 25.0 on pci0
em0: Using MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:1d:09:99:b5:ee
uhci0: <Intel 82801I (ICH9) USB controller> port 0xfe00-0xfe1f irq 16 at device 26.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x2f00
usbus0: <Intel 82801I (ICH9) USB controller> on uhci0
uhci1: <Intel 82801I (ICH9) USB controller> port 0xfd00-0xfd1f irq 21 at device 26.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x2f00
usbus1: <Intel 82801I (ICH9) USB controller> on uhci1
uhci2: <Intel 82801I (ICH9) USB controller> port 0xfc00-0xfc1f irq 19 at device 26.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x2f00
usbus2: <Intel 82801I (ICH9) USB controller> on uhci2
ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfdffe000-0xfdffe3ff irq 18 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0
hdac0: <Intel 82801I High Definition Audio Controller> mem 0xfdff4000-0xfdff7fff irq 22 at device 27.0 on pci0
hdac0: HDA Driver Revision: 20100226_0142
hdac0: [ITHREAD]
uhci3: <Intel 82801I (ICH9) USB controller> port 0xfb00-0xfb1f irq 23 at device 29.0 on pci0
uhci3: [ITHREAD]
usbus4: <Intel 82801I (ICH9) USB controller> on uhci3
uhci4: <Intel 82801I (ICH9) USB controller> port 0xfa00-0xfa1f irq 19 at device 29.1 on pci0
uhci4: [ITHREAD]
usbus5: <Intel 82801I (ICH9) USB controller> on uhci4
uhci5: <Intel 82801I (ICH9) USB controller> port 0xf900-0xf91f irq 18 at device 29.2 on pci0
uhci5: [ITHREAD]
usbus6: <Intel 82801I (ICH9) USB controller> on uhci5
ehci1: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfdffd000-0xfdffd3ff irq 23 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <Intel 82801I (ICH9) USB 2.0 controller> on ehci1
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH9 SATA300 controller> port 0xf800-0xf807,0xf700-0xf703,0xf600-0xf607,0xf500-0xf503,0xf400-0xf40f,0xf300-0xf30f irq 19 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci1: <Intel ICH9 SATA300 controller> port 0xf100-0xf107,0xf000-0xf003,0xef00-0xef07,0xee00-0xee03,0xed00-0xed0f,0xec00-0xec0f irq 19 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci1
ata5: [ITHREAD]
acpi_tz0: <Thermal Zone> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: parallel port not found.
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 927092706000927
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 927092706000927
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 927092706000927
device_attach: est2 attach returned 6
p4tcc2: <CPU Frequency Thermal Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 927092706000927
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
ad4: 305245MB <Seagate ST3320620AS 3.ADG> at ata2-master UDMA100 SATA 3Gb/s
GEOM: ad4: partition 3 does not start on a track boundary.
GEOM: ad4: partition 3 does not end on a track boundary.
GEOM: ad4: partition 2 does not start on a track boundary.
GEOM: ad4: partition 2 does not end on a track boundary.
GEOM: ad4s3: geometry does not match label (255h,63s != 16h,63s).
uhub3: 6 ports with 6 removable, self powered
uhub7: 6 ports with 6 removable, self powered
ugen3.2: <Seagate> at usbus3
umass0: <Seagate FreeAgent Go, class 0/0, rev 2.00/1.48, addr 2> on usbus3
umass0:  SCSI over Bulk-Only; quirks = 0x0000
ugen7.2: <TEAC> at usbus7
umass1: <TEAC CA-200, class 0/0, rev 2.00/4.08, addr 2> on usbus7
umass1:  SCSI over Bulk-Only; quirks = 0x0000
umass0:1:0:-1: Attached to scbus1
umass1:2:1:-1: Attached to scbus2
acd0: DVDR <TSSTcorp CDDVDW SH-S223C/ID01> at ata3-master UDMA100 SATA 1.5Gb/s
hdac0: HDA Codec #2: Realtek ALC888
pcm0: <HDA Realtek ALC888 PCM #0 Analog> at cad 2 nid 1 on hdac0
pcm1: <HDA Realtek ALC888 PCM #1 Analog> at cad 2 nid 1 on hdac0
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 
(probe2:ata3:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe2:ata3:0:0:0): CAM status: SCSI Status Error
(probe2:ata3:0:0:0): SCSI status: Check Condition
(probe2:ata3:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed)
(probe1:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe1:umass-sim1:1:0:0): CAM status: SCSI Status Error
(probe1:umass-sim1:1:0:0): SCSI status: Check Condition
(probe1:umass-sim1:1:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(probe0:umass-sim1:1:0:1): TEST UNIT READY. CDB: 0 20 0 0 0 0 
(probe0:umass-sim1:1:0:1): CAM status: SCSI Status Error
(probe0:umass-sim1:1:0:1): SCSI status: Check Condition
(probe0:umass-sim1:1:0:1): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(probe0:umass-sim1:1:0:2): TEST UNIT READY. CDB: 0 40 0 0 0 0 
(probe0:umass-sim1:1:0:2): CAM status: SCSI Status Error
(probe0:umass-sim1:1:0:2): SCSI status: Check Condition
(probe0:umass-sim1:1:0:2): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(probe0:umass-sim1:1:0:3): TEST UNIT READY. CDB: 0 60 0 0 0 0 
(probe0:umass-sim1:1:0:3): CAM status: SCSI Status Error
(probe0:umass-sim1:1:0:3): SCSI status: Check Condition
(probe0:umass-sim1:1:0:3): SCSI sense: NOT READY asc:3a,0 (Medium not present)
da0 at umass-sim0 bus 0 scbus1 target 0 lun 0
da0: <Seagate FreeAgent Go 0148> Fixed Direct Access SCSI-4 device 
da0: 40.000MB/s transfers
da0: 476940MB (976773167 512 byte sectors: 255H 63S/T 60801C)
cd0 at ata3 bus 0 scbus3 target 0 lun 0
cd0: <TSSTcorp CDDVDW SH-S223C ID01> Removable CD-ROM SCSI-0 device 
cd0: 100.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
da1 at umass-sim1 bus 1 scbus2 target 0 lun 0
da1: <TEAC USB   HS-CF Card 4.08> Removable Direct Access SCSI-0 device 
da1: 40.000MB/s transfers
da1: Attempt to query device size failed: NOT READY, Medium not present
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
da2 at umass-sim1 bus 1 scbus2 target 0 lun 1
da2: <TEAC USB   HS-xD/SM 4.08> Removable Direct Access SCSI-0 device 
da2: 40.000MB/s transfers
da2: Attempt to query device size failed: NOT READY, Medium not present
da3 at umass-sim1 bus 1 scbus2 target 0 lun 2
da3: <TEAC USB   HS-MS Card 4.08> Removable Direct Access SCSI-0 device 
da3: 40.000MB/s transfers
da3: Attempt to query device size failed: NOT READY, Medium not present
da4 at umass-sim1 bus 1 scbus2 target 0 lun 3
da4: <TEAC USB   HS-SD Card 4.08> Removable Direct Access SCSI-0 device 
da4: 40.000MB/s transfers
da4: Attempt to query device size failed: NOT READY, Medium not present
ugen2.2: <Dell> at usbus2
uhub8: <Dell USB Keyboard Hub> on usbus2
Trying to mount root from ufs:/dev/ad4s3a
uhub8: 3 ports with 2 removable, bus powered
ugen2.3: <Dell> at usbus2
ukbd0: <Dell USB Keyboard Hub> on usbus2
kbd2 at ukbd0
uhid0: <Dell USB Keyboard Hub> on usbus2
ugen2.4: <vendor 0x0461> at usbus2
ums0: <vendor 0x0461 USB Optical Mouse, class 0/0, rev 2.00/2.00, addr 4> on usbus2
ums0: 3 buttons and [XYZ] coordinates ID=0
em0: link state changed to UP