bge0 problem on 6.1-PRERELEASE

SungGON Yi. skon at kr.FreeBSD.org
Fri Mar 31 03:13:02 UTC 2006


I am using 6.x on Tyan S2885ANRF board and add one more lan card.
Deive names are bge0 (board lan) and bge1 (additional land card). 

These worked well on FreeBSD 6.0-amd64 stable.
But when I updated to 6.1-PRERELEASE version, I had below messages and bge0 did not work.
bge1 worked well as before. 

--------------------------------
bge0: watchdog timeout -- resetting
--------------------------------

I am using 6.0-RELEASE now. 

--------------------------------
bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem 0xfc6f0000-0xfc6fffff irq 27 at device 8.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: Ethernet address: 00:04:76:f3:e8:c9
bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xfc6e0000-0xfc6effff irq 24 at device 9.0 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge1: Ethernet address: 00:e0:81:27:a0:f6
-----------------------------------

--------------------------------------------------------------------------------------------------------------------------------
$ ifconfig
bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
 options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
 inet6 fe80::204:76ff:fef3:e8c9%bge0 prefixlen 64 scopeid 0x1 
 inet xxx.xxx.xxx.xxx netmask 0xffffff00 broadcast xxx.xxx.xxx.xxx
 ether 00:04:76:f3:e8:c9
 media: Ethernet autoselect (100baseTX <full-duplex>)
 status: active
bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
 options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
 inet6 fe80::2e0:81ff:fe27:a0f6%bge1 prefixlen 64 scopeid 0x2 
 inet 192.168.24.106 netmask 0xffffff00 broadcast 192.168.24.255
 ether 00:e0:81:27:a0:f6
 media: Ethernet autoselect (1000baseTX <full-duplex>)
 status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
 inet6 ::1 prefixlen 128 
 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 
 inet 127.0.0.1 netmask 0xff000000 
pfsync0: flags=0<> mtu 2020
pflog0: flags=0<> mtu 33160
------------------------------------

SungGON Yi.
skon at kr.FreeBSD.org


More information about the freebsd-questions mailing list