Broadcom BCM4401-B0 and memory upgrade issue.

Tue Jan 24 04:11:24 PST 2006

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hello,

After the memory upgrade on my Laptop (HP nx5000) FreeBSD 6.0 stable, the
driver for NIC bfe0 (Broadcom BCM4401-B0) stops working. The NIC LED lights
are on. The bfe0 interface is up and active. However, I got a permanent
message on the console:

bfe0: watching timeout -- resetting.

This occurs in the case when I compile the new kernel without bfe driver and
load the bfe driver as module (if_bfe.ko). In the case when the driver is
compiled into the kernel, the system stalls during the boot or whenever I
try to configure the interface.

This behavior is reproducible on FreeBSD 6.0 RELENG_6 stable compiled from
checkout on 02.11.2005 and also from checkout on 23.01.2006. 

The problem occur only if the upgraded memory (RAM) exceeds 1GB. It does not
depend on the manufacturer of the memory chips and the number of occupied
slots. I already tried 2 1GB modules from Infineon DDR400 CL3 and two
modules from Crucial DDR333, CL2.5. It also does not depend on ACPI.

The problem does not occur under Windows XP.

What should be my next steps, in order to get NIC working?
Can I try NDIS for this NIC?

Any ideas are welcome. Thank you.

Here is the dmesg output before upgrade and after.

Befor:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 6.0-STABLE #0: Mon Jan 23 17:00:54 CET 2006
    root at localhost:/usr/obj/usr/src/sys/MYKERNEL60
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1500MHz (1495.16-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Stepping = 5

Features=0xa7e9fbbf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMO
V,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE>
  Features2=0x180<EST,TM2>
real memory  = 1065156608 (1015 MB)
avail memory = 1033392128 (985 MB)
ACPI APIC Table: <COMPAQ CPQ0058 >
ioapic0: Changing APIC ID to 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard kqemu version 0x00010200
kqemu: KQEMU installed, max_instances=4 max_locked_mem=128932kB.
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <COMPAQ CPQ0058> on motherboard
acpi0: Power Button (fixed)
acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 0.3 (no driver attached)
agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> port 0x2c30-0x2c37 mem
0x98000000-0x9fffffff,0x90400000-0x9047ffff irq 16 at device 2.0 on pci0
agp0: detected 8060k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x28c0-0x28df irq 16
at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x28e0-0x28ff irq 19
at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x2c00-0x2c1f irq 18
at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/DBL/DBM (ICH4) USB 2.0 controller> mem
0x90500000-0x905003ff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/DBL/DBM (ICH4) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <network> at device 4.0 (no driver attached)
cbb0: <PCI-CardBus Bridge> mem 0x90180000-0x90180fff irq 18 at device 6.0 on
pci1
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <PCI-CardBus Bridge> mem 0x90200000-0x90200fff irq 18 at device 6.1 on
pci1
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pci1: <mass storage> at device 6.3 (no driver attached)
fwohci0: <Texas Instruments TSB43AB22/A> mem
0x90300000-0x903007ff,0x90000000-0x90003fff irq 23 at device 13.0 on pci1
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 71:8b:50:00:29:b1:19:a3
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 72:8b:50:b1:19:a3
fwe0: Ethernet address: 72:8b:50:b1:19:a3
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
bfe0: <Broadcom BCM4401-B0 Fast Ethernet> mem 0x90080000-0x90081fff irq 20
at device 14.0 on pci1
miibus0: <MII bus> on bfe0
bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0
bmtphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bfe0: Ethernet address: 00:08:02:e5:f5:73
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2c20-0x2c2f irq 18 at device 31.1 on
pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
acpi_tz2: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x9 irq 1 on atkbdc0 kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
fdc0: [FAST]
sio1: <Generic IRDA-compatible device> port 0x3e8-0x3ef,0x100-0x107 irq 3
drq 3 on acpi0
sio1: type 16550A
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77a irq 7 drq 1
on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1495156220 Hz quality 800 Timecounters tick
every 1.000 msec
ad0: 57231MB <HTS726060M9AT00 MH4OA60A> at ata0-master PIO4
acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-4241N/0C29> at ata1-master PIO4
Trying to mount root from ufs:/dev/ad0s1a
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding disabled,
default to deny, logging disabled

After:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 6.0-STABLE #0: Mon Jan 23 17:00:54 CET 2006
    root at localhost:/usr/obj/usr/src/sys/MYKERNEL60
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1500MHz (1495.15-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Stepping = 5

Features=0xa7e9fbbf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMO
V,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE>
  Features2=0x180<EST,TM2>
real memory  = 1333592064 (1271 MB)
avail memory = 1297063936 (1236 MB)
ACPI APIC Table: <COMPAQ CPQ0058 >
ioapic0: Changing APIC ID to 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard kqemu version 0x00010200
kqemu: KQEMU installed, max_instances=4 max_locked_mem=131072kB.
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <COMPAQ CPQ0058> on motherboard
acpi0: Power Button (fixed)
acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 0.3 (no driver attached)
agp0: <Intel 8285xM (85xGM GMCH) SVGA controller> port 0x2c30-0x2c37 mem
0x98000000-0x9fffffff,0x90400000-0x9047ffff irq 16 at device 2.0 on pci0
agp0: detected 8060k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x28c0-0x28df irq 16
at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x28e0-0x28ff irq 19
at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x2c00-0x2c1f irq 18
at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/DBL/DBM (ICH4) USB 2.0 controller> mem
0x90500000-0x905003ff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/DBL/DBM (ICH4) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <network> at device 4.0 (no driver attached)
cbb0: <PCI-CardBus Bridge> mem 0x90180000-0x90180fff irq 18 at device 6.0 on
pci1
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <PCI-CardBus Bridge> mem 0x90200000-0x90200fff irq 18 at device 6.1 on
pci1
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pci1: <mass storage> at device 6.3 (no driver attached)
fwohci0: <Texas Instruments TSB43AB22/A> mem
0x90300000-0x903007ff,0x90000000-0x90003fff irq 23 at device 13.0 on pci1
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 71:8b:50:00:29:b1:19:a3
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 72:8b:50:b1:19:a3
fwe0: Ethernet address: 72:8b:50:b1:19:a3
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
bfe0: <Broadcom BCM4401-B0 Fast Ethernet> mem 0x90080000-0x90081fff irq 20
at device 14.0 on pci1
miibus0: <MII bus> on bfe0
bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0
bmtphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bfe0: Ethernet address: 00:08:02:e5:f5:73
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2c20-0x2c2f irq 18 at device 31.1 on
pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
acpi_tz2: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x9 irq 1 on atkbdc0 kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
fdc0: [FAST]
sio1: <Generic IRDA-compatible device> port 0x3e8-0x3ef,0x100-0x107 irq 3
drq 3 on acpi0
sio1: type 16550A
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77a irq 7 drq 1
on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1495153730 Hz quality 800 Timecounters tick
every 1.000 msec
ad0: 57231MB <HTS726060M9AT00 MH4OA60A> at ata0-master PIO4
acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-4241N/0C29> at ata1-master PIO4
Trying to mount root from ufs:/dev/ad0s1a
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding disabled,
default to deny, logging disabled
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (MingW32)

iD8DBQFD1hk4KOV0oHioLCARAtfmAJ9B0Cq2YqsnRw/hlv8hH7JFRBc55gCgmKP6
aSk+PiT22fSM305XPCrb2W8=
=F6TN
-----END PGP SIGNATURE-----