USB 2.0 Support

[Nathan Vidican]

We've been using an external USB hard disk enclosure with a 250GB Western 
Digital ATA-133 disk inside it. All works well, but our mainboard (MSI K8 
Master) only has USB 1.1 on-board, we've tried a USB 2.0 PCI card, but it is 
apparently not picked up properly when the kernel boots. Do I need to disable 
the on-board USB, or are there only certain chipsets which FreeBSD supports for 
USB 2.0 ? The kernel apaprently detects the card (usb2/usb3 <NEC uPD 9210 USB 
controller>), but it appears as 1.0, not 2.0; or is this the driver version? 
Anyhow, aside from picking it up, it does not detect the removeable drive nor 
are we able to use the USB 2.0 ports anyhow. USB 1.1 off the mainboard detects 
the drive fine, we're able to mount and use it with no problems accept a 
gruellingly slow transfer... USB 2.0 would really help here I'm hoping. We're 
running 6.0-RC1, with custom kernel (pretty much GENERIC -minus drivers we don't 
need, plus SMP), dmesg as follows:

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RC1 #0: Sat Oct 15 16:29:44 EDT 2005
     root at wmptwo.wmptl.net:/usr/src/sys/amd64/compile/SMP
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 244 (1794.42-MHz K8-class CPU)
   Origin = "AuthenticAMD"  Id = 0xf5a  Stepping = 10
 
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
   AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
real memory  = 2146893824 (2047 MB)
avail memory = 2062491648 (1966 MB)
ACPI APIC Table: <PTLTD          APIC  >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
  cpu0 (BSP): APIC ID:  0
  cpu1 (AP): APIC ID:  1
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
acpi0: <PTLTD    XSDT> on motherboard
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 15 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 10 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 11 on acpi0
unknown: I/O range not supported
unknown: I/O range not supported
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x8000-0x807f,0x8080-0x80ff iomem 
0xd8000-0xdbfff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
ohci0: <OHCI (generic) USB controller> mem 0xfb100000-0xfb100fff irq 19 at 
device 0.0 on pci1
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfb101000-0xfb101fff irq 19 at 
device 0.1 on pci1
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
atapci0: <SiI 3114 SATA150 controller> port 
0x2420-0x2427,0x2414-0x2417,0x2418-0x241f,0x2410-0x2413,0x2400-0x240f mem 
0xfb105000-0xfb1053ff irq 16 at device 5.0 on pci1
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
ata4: <ATA channel 2> on atapci0
ata5: <ATA channel 3> on atapci0
pci1: <display, VGA> at device 7.0 (no driver attached)
ohci2: <NEC uPD 9210 USB controller> mem 0xfb103000-0xfb103fff irq 16 at device 
9.0 on pci1
ohci2: [GIANT-LOCKED]
usb2: OHCI version 1.0
usb2: <NEC uPD 9210 USB controller> on ohci2
usb2: USB revision 1.0
uhub2: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 1 port with 1 removable, self powered
ohci3: <NEC uPD 9210 USB controller> mem 0xfb104000-0xfb104fff irq 17 at device 
9.1 on pci1
ohci3: [GIANT-LOCKED]
usb3: OHCI version 1.0
usb3: <NEC uPD 9210 USB controller> on ohci3
usb3: USB revision 1.0
uhub3: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 1 port with 1 removable, self powered
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <AMD 8111 UDMA133 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1000-0x100f at device 7.1 on pci0
ata0: <ATA channel 0> on atapci1
ata1: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
pci0: <bridge> at device 7.3 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem 
0xfd010000-0xfd01ffff,0xfd000000-0xfd00ffff irq 26 at device 2.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 
1000baseTX-FDX, auto
bge0: Ethernet address: 00:11:09:a9:d7:9e
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem 
0xfd030000-0xfd03ffff,0xfd020000-0xfd02ffff irq 24 at device 2.1 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 
1000baseTX-FDX, auto
bge1: Ethernet address: 00:11:09:a9:d7:9f
pci0: <base peripheral, interrupt controller> at device 10.1 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci3: <ACPI PCI bus> on pcib3
3ware device driver for 9000 series storage controllers, version: 3.60.00.017
twa0: <3ware 9000 series Storage Controller> port 0x3000-0x30ff mem 
0xfd100000-0xfd1000ff,0xfd800000-0xfdffffff irq 28 at device 1.0 on pci3
twa0: [FAST]
twa0: INFO: (0x15: 0x1300): Controller details:: 4 ports, Firmware FE9X 
2.04.00.005, BIOS BE9X 2.03.01.047
pci0: <base peripheral, interrupt controller> at device 11.1 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
orm0: <ISA Option ROMs> at iomem 
0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff,0xcb000-0xcc7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
acd0: DMA limited to UDMA33, controller found non-ATA66 cable
acd0: CDRW <LITE-ON COMBO SOHC-5232K/NK0G> at ata0-master UDMA33
SMP: AP CPU #1 Launched!
da0 at twa0 bus 0 target 0 lun 0
da0: <3ware Logical Disk 00 1.00> Fixed Direct Access SCSI-0 device
da0: 100.000MB/s transfers
da0: 715224MB (1464778752 512 byte sectors: 255H 63S/T 91178C)
Trying to mount root from ufs:/dev/da0s2a
bge0: link state changed to UP


Thanks one-and-all

-- 
Nathan Vidican
nvidican at wmptl.com
Windsor Match Plate & Tool Ltd.
http://www.wmptl.com/