Installation instructions for Firefox somewhere?
Ted Mittelstaedt
tedm at toybox.placo.com
Tue Mar 1 23:31:19 GMT 2005
Anthony,
It appears you have a narrow-SCSI max 10MB sync disk drive and a
ultra -3 20MB sync disk drive on the same adapter card.
Such a combination is iffy at best. Even worse is it's
different manufacturers - while SCSI is supposed to be
standard, the standard isn't completely followed by all
manufacturers. It is not as bad as mixing IDE but it isn't the
best.
Quantum (now Maxtor) does not have detailed specs as
to what exactly a Quantum XP34550S is, whether it's narrow
or wide or differential SCSI. I can see it's an Atlas 2 drive
but there's both narrow and wide Atlas 2s I would assume this
is a wide drive since it's synced at 20.000MB/s transfers
if so how are you attaching it to the adapter card? Do you
have the narrow Seagate and the wide Quantum on
the same adapter card? If so then your really asking for trouble.
And those 68-50 pin scsi adapters are bullshit if that is what
you are using.
If the Quantum is a narrow drive, then going in to the Adaptec
card's BIOS and forcing negotiation on the Quantum to 10MB/s MIGHT fix
the trouble,
assuming FreeBSD picks up the 10MB. But, from the looks of it you
have 2 SCSI adapters, one probably on motherboard, the other
on a card, the disks attached to the motherboard card (which has
no BIOS) and something else attached to the card (which does
have a BIOS) Perhaps EISA-config could set it if this system
has EISA slots?
Standard troubleshooting is to put in 1 drive, install FreeBSD
and work it out and see if it blows, then pull that drive and
put in the other, then install FreeBSD and work it and see if it blows.
If you do that my guess is you will find FreeBSD doesen't blow
on either disk when they are separated. Only when they are in
the same machine.
Fortunately 4GB SCSI disks are cheap on the used market. I've
never cared that much for Quantum SCSI, they were the OEM for
Apple for years and I never felt that the old Mac's obeyed the
SCSI standard completely, and that Quantum catered to this. It
also speaks volumes that Quantum couldn't make a go of it in the
disk market and sold out to Maxtor. As a result I run mostly
Seagate SCSI disks and I have never had a problem on Seagate<->Adaptec
combos. If it was my machine I'd dig around for another Seagate SCSI
disk and jettison the Quantum, but I will admit this is personal
preference.
Ted
> -----Original Message-----
> From: owner-freebsd-questions at freebsd.org
> [mailto:owner-freebsd-questions at freebsd.org]On Behalf Of Anthony
> Atkielski
> Sent: Tuesday, March 01, 2005 4:05 AM
> To: freebsd-questions at freebsd.org
> Subject: Re: Installation instructions for Firefox somewhere?
>
>
> Chris Hodgins writes:
>
> > I might have missed it but I can't find any information
> about what SCSI
> > errors you are receiving. Why don't you post the errors you
> are seeing
> > and/or perhaps your dmesg output as well and maybe someone can help
> > you. Without more information noone can do more than guess.
>
> Here it is, again:
>
> I get constant streams of messages concerning my disks on the console
> whenever I have a lot of disk activity on my system (2x SCSI disks, no
> IDE or other disks). I'd very much like to know what's going
> on (there's
> nothing wrong with the hardware, so either it's a
> configuration problem,
> or it's a bug).
>
> There doesn't seem to be any data loss or corruption occurring. I've
> had one or two panics, though (which may or may not have caused data
> loss--it's hard to tell).
>
> While recompiling the kernel, the system stalled periodically (at least
> anything involving disk I/O stalled) and generated several hundred
> kilobytes of messages looking like this:
>
> Feb 26 20:09:23 contactdish kernel: (da0:ahc0:0:0:0): Retrying Command
> Feb 26 20:09:23 contactdish kernel: (da0:ahc0:0:0:0): Request Requeued
> Feb 26 20:09:23 contactdish kernel: (da0:ahc0:0:0:0): Retrying Command
> Feb 26 20:09:23 contactdish kernel: (da0:ahc0:0:0:0): Queue Full
> Feb 26 20:09:23 contactdish kernel: (da0:ahc0:0:0:0): tagged
> openings now 64
> Feb 26 20:09:23 contactdish kernel: (da0:ahc0:0:0:0): Retrying Command
> Feb 26 20:09:24 contactdish kernel: (da0:ahc0:0:0:0): Queue Full
> Feb 26 20:09:24 contactdish kernel: (da0:ahc0:0:0:0): tagged
> openings now 63
> Feb 26 20:09:24 contactdish kernel: (da0:ahc0:0:0:0): Retrying Command
> Feb 26 20:09:26 contactdish kernel: (da1:ahc0:0:2:0): Request Requeued
> Feb 26 20:09:26 contactdish kernel: (da1:ahc0:0:2:0): Retrying Command
> Feb 26 20:09:26 contactdish kernel: (da1:ahc0:0:2:0): Queue Full
> Feb 26 20:09:26 contactdish kernel: (da1:ahc0:0:2:0): Retrying Command
>
> In addition, I sometimes get bursts of much longer messages, looking
> something like this:
>
> Feb 25 20:09:29 contactdish kernel: ahc0: Recovery Initiated
> Feb 25 20:09:29 contactdish kernel: >>>>>>>>>>>>>>>>>> Dump
> Card State Begins <<<<<<<<<<<<<<<<<
> Feb 25 20:09:29 contactdish kernel: ahc0: Dumping Card State
> in Message-in phase, at SEQADDR 0x162
> Feb 25 20:09:29 contactdish kernel: Card was paused
> Feb 25 20:09:29 contactdish kernel: ACCUM = 0xcb, SINDEX =
> 0x0, DINDEX = 0x88, ARG_2 = 0x0
> Feb 25 20:09:29 contactdish kernel: HCNT = 0x0 SCBPTR = 0xa
> Feb 25 20:09:29 contactdish kernel:
> SCSISIGI[0xe6]:(REQI|BSYI|MSGI|IOI|CDI) ERROR[0x0]
> Feb 25 20:09:29 contactdish kernel: SCSIBUSL[0x0]
> LASTPHASE[0xe0]:(MSGI|IOI|CDI) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
> Feb 25 20:09:29 contactdish kernel: SBLKCTL[0x0]
> SCSIRATE[0xf]:(SXFR_ULTRA2) SEQCTL[0x10]:(FASTMODE)
> Feb 25 20:09:29 contactdish kernel: SEQ_FLAGS[0x0]
> SSTAT0[0x7]:(DMADONE|SPIORDY|SDONE)
> Feb 25 20:09:29 contactdish kernel:
> SSTAT1[0x3]:(REQINIT|PHASECHG) SSTAT2[0x0] SSTAT3[0x0]
> Feb 25 20:09:29 contactdish kernel: SIMODE0[0x0]
> SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO)
> Feb 25 20:09:29 contactdish kernel:
> SXFRCTL0[0xa8]:(SPIOEN|FAST20|DFON) DFCNTRL[0x0]
> DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
> Feb 25 20:09:29 contactdish kernel: STACK: 0x105 0x100 0xe5 0x163
> Feb 25 20:09:29 contactdish kernel: SCB count = 100
> Feb 25 20:09:29 contactdish kernel: Kernel NEXTQSCB = 19
> Feb 25 20:09:29 contactdish kernel: Card NEXTQSCB = 25
> Feb 25 20:09:29 contactdish kernel: QINFIFO entries: 25 71 31
> Feb 25 20:09:29 contactdish kernel: Waiting Queue entries:
> Feb 25 20:09:29 contactdish kernel: Disconnected Queue
> entries: 0:72 1:68 2:84 14:60 12:61 5:53
> Feb 25 20:09:29 contactdish kernel: QOUTFIFO entries:
> Feb 25 20:09:29 contactdish kernel: Sequencer Free SCB List:
> 10 6 9 3 7 4 13 11 15 8
> Feb 25 20:09:29 contactdish kernel: Sequencer SCB Info:
> Feb 25 20:09:29 contactdish kernel: 0
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0x48]
> Feb 25 20:09:29 contactdish kernel: 1
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0x44]
> Feb 25 20:09:29 contactdish kernel: 2
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0x54]
> Feb 25 20:09:29 contactdish kernel: 3
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 4
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 5
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0x35]
> Feb 25 20:09:29 contactdish kernel: 6
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 7
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 8
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 9
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 10
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 11
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 12
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0x3d]
> Feb 25 20:09:29 contactdish kernel: 13
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: 14
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0x3c]
> Feb 25 20:09:29 contactdish kernel: 15
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Feb 25 20:09:29 contactdish kernel: Pending list:
> Feb 25 20:09:29 contactdish kernel: 31
> SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 71
> SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 25
> SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 17
> SCB_CONTROL[0xe8]:(ULTRAENB|TAG_ENB|DISCENB|TARGET_SCB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 72
> SCB_CONTROL[0x68]:(ULTRAENB|TAG_ENB|DISCENB) SCB_SCSIID[0x27]
> Feb 25 20:09:29 contactdish kernel: SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 12
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 81
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 94
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 73
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 69
> SCB_CONTROL[0x6c]:(DISCONNECTED|ULTRAENB|TAG_ENB|DISCENB)
> Feb 25 20:09:29 contactdish kernel: SCB_SCSIID[0x27] SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 68
> SCB_CONTROL[0x68]:(ULTRAENB|TAG_ENB|DISCENB) SCB_SCSIID[0x27]
> Feb 25 20:09:29 contactdish kernel: SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 84
> SCB_CONTROL[0x68]:(ULTRAENB|TAG_ENB|DISCENB) SCB_SCSIID[0x27]
> Feb 25 20:09:29 contactdish kernel: SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 60
> SCB_CONTROL[0x68]:(ULTRAENB|TAG_ENB|DISCENB) SCB_SCSIID[0x27]
> Feb 25 20:09:29 contactdish kernel: SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 61
> SCB_CONTROL[0x68]:(ULTRAENB|TAG_ENB|DISCENB) SCB_SCSIID[0x27]
> Feb 25 20:09:29 contactdish kernel: SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: 53
> SCB_CONTROL[0x68]:(ULTRAENB|TAG_ENB|DISCENB) SCB_SCSIID[0x27]
> Feb 25 20:09:29 contactdish kernel: SCB_LUN[0x0]
> Feb 25 20:09:29 contactdish kernel: Kernel Free SCB list: 45
> 22 2 34 36 51 14 75 27 66 21 48 41 64 13 43 16 99 24 20 33 9
> 86 10 56 23 0 82 59 26 50 97 49 88
> 98 77 32 96 5 38 7 76 87 89 67 30 4 29 55 62 74 18 58 11 85 39
> 46 8 44 63 35 28 47 40 54 1 42 79 15 3 80 6 95 70 57 52 83 78
> 37 65 93 92 91 90
> Feb 25 20:09:29 contactdish kernel:
> Feb 25 20:09:29 contactdish kernel: <<<<<<<<<<<<<<<<< Dump
> Card State Ends >>>>>>>>>>>>>>>>>>
> Feb 25 20:09:29 contactdish kernel: (da1:ahc0:0:2:0): SCB 0x49
> - timed out
> Feb 25 20:09:29 contactdish kernel: sg[0] - Addr 0x1309b000 :
> Length 2048
> Feb 25 20:09:29 contactdish kernel: (da1:ahc0:0:2:0): Queuing a BDR SCB
> Feb 25 20:09:29 contactdish kernel: ahc0: Timedout SCBs
> already complete. Interrupts may not be functioning.
>
> I'd very much like to know what's going on. Do I need to fix something
> in the configuration, or is there a bug somewhere?
>
> For further information, here is the output I got at boot time
> (with the
> -v option):
>
> Feb 26 16:36:26 contactdish syslogd: kernel boot file is
> /boot/kernel/kernel
> Feb 26 16:36:26 contactdish kernel: Copyright (c) 1992-2004
> The FreeBSD Project.
> Feb 26 16:36:26 contactdish kernel: Copyright (c) 1979, 1980,
> 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> Feb 26 16:36:26 contactdish kernel: The Regents of the
> University of California. All rights reserved.
> Feb 26 16:36:26 contactdish kernel: FreeBSD 5.3-RELEASE #1:
> Fri Feb 25 20:47:12 CET 2005
> Feb 26 16:36:26 contactdish kernel:
> root at contactdish.atkielski.com:/usr/obj/usr/src/sys/CONTACTDISH
> Feb 26 16:36:26 contactdish kernel: Preloaded elf kernel
> "/boot/kernel/kernel" at 0xc07b5000.
> Feb 26 16:36:26 contactdish kernel: Calibrating clock(s) ...
> i8254 clock: 1193100 Hz
> Feb 26 16:36:26 contactdish kernel: CLK_USE_I8254_CALIBRATION
> not specified - using default frequency
> Feb 26 16:36:26 contactdish kernel: Timecounter "i8254"
> frequency 1193182 Hz quality 0
> Feb 26 16:36:26 contactdish kernel: Calibrating TSC clock ...
> TSC clock: 195744728 Hz
> Feb 26 16:36:26 contactdish kernel: CPU: Pentium Pro
> (195.74-MHz 686-class CPU)
> Feb 26 16:36:26 contactdish kernel: Origin = "GenuineIntel"
> Id = 0x617 Stepping = 7
> Feb 26 16:36:26 contactdish kernel:
> Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTR
> R,PGE,MCA,CMOV>
> Feb 26 16:36:26 contactdish kernel: real memory = 402653184 (384 MB)
> Feb 26 16:36:26 contactdish kernel: Physical memory chunk(s):
> Feb 26 16:36:26 contactdish kernel: 0x0000000000001000 -
> 0x000000000009efff, 647168 bytes (158 pages)
> Feb 26 16:36:26 contactdish kernel: 0x0000000000100000 -
> 0x00000000003fffff, 3145728 bytes (768 pages)
> Feb 26 16:36:26 contactdish kernel: 0x0000000000829000 -
> 0x000000001790ffff, 386822144 bytes (94439 pages)
> Feb 26 16:36:26 contactdish kernel: avail memory = 388534272 (370 MB)
> Feb 26 16:36:26 contactdish kernel: MP Configuration Table
> version 1.1 found at 0xc00f9610
> Feb 26 16:36:26 contactdish kernel: APIC: Using the MPTable enumerator.
> Feb 26 16:36:26 contactdish kernel: SMP: Added CPU 1 (BSP)
> Feb 26 16:36:26 contactdish kernel: SMP: Added CPU 0 (AP)
> Feb 26 16:36:26 contactdish kernel: MPTable: <HP XX >
> Feb 26 16:36:26 contactdish kernel: APIC ID: physical 0, logical 0:0
> Feb 26 16:36:26 contactdish kernel: APIC ID: physical 1, logical 0:1
> Feb 26 16:36:26 contactdish kernel: FreeBSD/SMP:
> Multiprocessor System Detected: 2 CPUs
> Feb 26 16:36:26 contactdish kernel: cpu0 (BSP): APIC ID: 1
> Feb 26 16:36:26 contactdish kernel: cpu1 (AP): APIC ID: 0
> Feb 26 16:36:26 contactdish kernel: bios32: Found BIOS32
> Service Directory header at 0xc00fdcc0
> Feb 26 16:36:26 contactdish kernel: bios32: Entry = 0xfdc90
> (c00fdc90) Rev = 0 Len = 1
> Feb 26 16:36:26 contactdish kernel: pcibios: PCI BIOS entry at
> 0xf0000+0xdcd0
> Feb 26 16:36:26 contactdish kernel: pnpbios: Found PnP BIOS
> data at 0xc00faa10
> Feb 26 16:36:26 contactdish kernel: pnpbios: Entry =
> f0000:a8bd Rev = 1.0
> Feb 26 16:36:26 contactdish kernel: Other BIOS signatures found:
> Feb 26 16:36:26 contactdish kernel: ioapic0: Changing APIC ID to 16
> Feb 26 16:36:26 contactdish kernel: ioapic0: Assuming intbase of 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: Routing external
> 8259A's -> intpin 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 0 ->
> ExtINT (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 1 -> ISA
> IRQ 1 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 2 -> ISA
> IRQ 2 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 3 -> ISA
> IRQ 3 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 4 -> ISA
> IRQ 4 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 5 -> ISA
> IRQ 5 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 6 -> ISA
> IRQ 6 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 7 -> ISA
> IRQ 7 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 8 -> ISA
> IRQ 8 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 9 -> ISA
> IRQ 9 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 10 -> ISA
> IRQ 10 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 11 -> ISA
> IRQ 11 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 12 -> ISA
> IRQ 12 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 13 -> ISA
> IRQ 13 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 14 -> ISA
> IRQ 14 (edge, high)
> Feb 26 16:36:26 contactdish kernel: ioapic0: intpin 15 -> ISA
> IRQ 15 (edge, high)
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 1
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 2
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 3
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 4
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 5
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 6
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 7
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 8
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 9
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 10
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 11
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 12
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 13
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 14
> Feb 26 16:36:26 contactdish kernel: MPTable: Ignoring global
> interrupt entry for pin 15
> Feb 26 16:36:26 contactdish kernel: lapic: Routing NMI -> LINT1
> Feb 26 16:36:26 contactdish kernel: ioapic0 <Version 1.1> irqs
> 0-15 on motherboard
> Feb 26 16:36:26 contactdish kernel: cpu0 BSP:
> Feb 26 16:36:26 contactdish kernel: ID: 0x01000000 VER:
> 0x00040011 LDR: 0x02000000 DFR: 0x0fffffff
> Feb 26 16:36:26 contactdish kernel: lint0: 0x00010700 lint1:
> 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
> Feb 26 16:36:26 contactdish kernel: mem: <memory>
> Feb 26 16:36:26 contactdish kernel: Pentium Pro MTRR support enabled
> Feb 26 16:36:26 contactdish kernel: null: <null device, zero device>
> Feb 26 16:36:26 contactdish kernel: io: <I/O>
> Feb 26 16:36:26 contactdish kernel: random: <entropy source,
> Software, Yarrow>
> Feb 26 16:36:26 contactdish kernel: npx0: [FAST]
> Feb 26 16:36:26 contactdish kernel: npx0: <math processor> on
> motherboard
> Feb 26 16:36:26 contactdish kernel: npx0: INT 16 interface
> Feb 26 16:36:26 contactdish kernel: pci_open(1): mode 1
> addr port (0x0cf8) is 0x80005840
> Feb 26 16:36:26 contactdish kernel: pci_open(1a):
> mode1res=0x80000000 (0x80000000)
> Feb 26 16:36:26 contactdish kernel: pci_cfgcheck: device
> 0 [class=000000] 1 [class=01018a] 2 [class=010000] [hdr=00] is
> there (id=80789004)
> Feb 26 16:36:26 contactdish kernel: pcibios: BIOS version 2.00
> Feb 26 16:36:26 contactdish kernel: pcib0: <Intel 82454KX/GX
> (Orion) host to PCI bridge> pcibus 0 on motherboard
> Feb 26 16:36:26 contactdish kernel: pci0: <PCI bus> on pcib0
> Feb 26 16:36:26 contactdish kernel: pci0: physical bus=0
> Feb 26 16:36:26 contactdish kernel: found-> vendor=0x8086,
> dev=0x0484, revid=0x88
> Feb 26 16:36:26 contactdish kernel: bus=0, slot=0, func=0
> Feb 26 16:36:26 contactdish kernel: class=00-00-00,
> hdrtype=0x00, mfdev=0
> Feb 26 16:36:26 contactdish kernel: cmdreg=0x0007,
> statreg=0x0200, cachelnsz=0 (dwords)
> Feb 26 16:36:26 contactdish kernel: lattimer=0x00 (0 ns),
> mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> Feb 26 16:36:26 contactdish kernel: map[20]: type 4, range 32,
> base 0000fff0, size 4, enabled
> Feb 26 16:36:26 contactdish kernel: found-> vendor=0x1095,
> dev=0x0646, revid=0x01
> Feb 26 16:36:26 contactdish kernel: bus=0, slot=1, func=0
> Feb 26 16:36:26 contactdish kernel: class=01-01-8a,
> hdrtype=0x00, mfdev=0
> Feb 26 16:36:26 contactdish kernel: cmdreg=0x0005,
> statreg=0x0280, cachelnsz=0 (dwords)
> Feb 26 16:36:26 contactdish kernel: lattimer=0x30 (1440 ns),
> mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
> Feb 26 16:36:26 contactdish kernel: intpin=a, irq=14
> Feb 26 16:36:26 contactdish kernel: map[10]: type 4, range 32,
> base 0000fe00, size 8, enabled
> Feb 26 16:36:26 contactdish kernel: map[14]: type 1, range 32,
> base fffdc000, size 12, enabled
> Feb 26 16:36:26 contactdish kernel: found-> vendor=0x9004,
> dev=0x8078, revid=0x00
> Feb 26 16:36:26 contactdish kernel: bus=0, slot=2, func=0
> Feb 26 16:36:26 contactdish kernel: class=01-00-00,
> hdrtype=0x00, mfdev=0
> Feb 26 16:36:26 contactdish kernel: cmdreg=0x0017,
> statreg=0x0280, cachelnsz=8 (dwords)
> Feb 26 16:36:26 contactdish kernel: lattimer=0xf8 (7440 ns),
> mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
> Feb 26 16:36:26 contactdish kernel: intpin=a, irq=10
> Feb 26 16:36:26 contactdish kernel: map[10]: type 3, range 32,
> base a0000000, size 24, enabled
> Feb 26 16:36:26 contactdish kernel: map[14]: type 1, range 32,
> base a1000000, size 14, enabled
> Feb 26 16:36:26 contactdish kernel: map[18]: type 1, range 32,
> base a1800000, size 23, enabled
> Feb 26 16:36:26 contactdish kernel: found-> vendor=0x102b,
> dev=0x051b, revid=0x00
> Feb 26 16:36:26 contactdish kernel: bus=0, slot=11, func=0
> Feb 26 16:36:26 contactdish kernel: class=03-00-00,
> hdrtype=0x00, mfdev=0
> Feb 26 16:36:26 contactdish kernel: cmdreg=0x0007,
> statreg=0x0280, cachelnsz=0 (dwords)
> Feb 26 16:36:26 contactdish kernel: lattimer=0xf8 (7440 ns),
> mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> Feb 26 16:36:26 contactdish kernel: intpin=a, irq=11
> Feb 26 16:36:26 contactdish kernel: map[10]: type 3, range 32,
> base fffcc000, size 12, enabled
> Feb 26 16:36:26 contactdish kernel: map[14]: type 4, range 32,
> base 0000ffc0, size 5, enabled
> Feb 26 16:36:26 contactdish kernel: map[18]: type 1, range 32,
> base ffe00000, size 20, enabled
> Feb 26 16:36:26 contactdish kernel: found-> vendor=0x8086,
> dev=0x1229, revid=0x01
> Feb 26 16:36:26 contactdish kernel: bus=0, slot=12, func=0
> Feb 26 16:36:26 contactdish kernel: class=02-00-00,
> hdrtype=0x00, mfdev=0
> Feb 26 16:36:26 contactdish kernel: cmdreg=0x0007,
> statreg=0x0280, cachelnsz=0 (dwords)
> Feb 26 16:36:26 contactdish kernel: lattimer=0xf8 (7440 ns),
> mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
> Feb 26 16:36:26 contactdish kernel: intpin=a, irq=11
> Feb 26 16:36:26 contactdish kernel: map[10]: type 4, range 32,
> base 0000fd00, size 8, enabled
> Feb 26 16:36:26 contactdish kernel: map[14]: type 1, range 32,
> base fffbc000, size 12, enabled
> Feb 26 16:36:26 contactdish kernel: found-> vendor=0x9004,
> dev=0x8178, revid=0x01
> Feb 26 16:36:26 contactdish kernel: bus=0, slot=13, func=0
> Feb 26 16:36:26 contactdish kernel: class=01-00-00,
> hdrtype=0x00, mfdev=0
> Feb 26 16:36:26 contactdish kernel: cmdreg=0x0007,
> statreg=0x0290, cachelnsz=8 (dwords)
> Feb 26 16:36:26 contactdish kernel: lattimer=0xf8 (7440 ns),
> mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
> Feb 26 16:36:26 contactdish kernel: intpin=a, irq=11
> Feb 26 16:36:26 contactdish kernel: powerspec 1 supports D0
> D3 current D0
> Feb 26 16:36:26 contactdish kernel: found-> vendor=0x8086,
> dev=0x84c5, revid=0x04
> Feb 26 16:36:26 contactdish kernel: bus=0, slot=20, func=0
> Feb 26 16:36:26 contactdish kernel: class=05-00-00,
> hdrtype=0x00, mfdev=0
> Feb 26 16:36:26 contactdish kernel: cmdreg=0x0000,
> statreg=0x0080, cachelnsz=0 (dwords)
> Feb 26 16:36:26 contactdish kernel: lattimer=0x00 (0 ns),
> mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> Feb 26 16:36:26 contactdish kernel: found-> vendor=0x8086,
> dev=0x84c4, revid=0x04
> Feb 26 16:36:26 contactdish kernel: bus=0, slot=25, func=0
> Feb 26 16:36:26 contactdish kernel: class=06-00-00,
> hdrtype=0x00, mfdev=0
> Feb 26 16:36:26 contactdish kernel: cmdreg=0x0147,
> statreg=0x2200, cachelnsz=8 (dwords)
> Feb 26 16:36:26 contactdish kernel: lattimer=0x20 (960 ns),
> mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> Feb 26 16:36:26 contactdish kernel: PCI-ISA bridge with
> incorrect subclass 0x0
> Feb 26 16:36:26 contactdish kernel: PCI-ISA bridge with
> incorrect subclass 0x0
> Feb 26 16:36:26 contactdish kernel: isab0: <PCI-ISA bridge> at
> device 0.0 on pci0
> Feb 26 16:36:26 contactdish kernel: isa0: <ISA bus> on isab0
> Feb 26 16:36:26 contactdish kernel: atapci0: <CMD 646 WDMA2
> controller> port
> 0xfff0-0xffff,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 14 at
> device 1.0 on pci0
> Feb 26 16:36:26 contactdish kernel: atapci0: Reserved 0x10
> bytes for rid 0x20 type 4 at 0xfff0
> Feb 26 16:36:26 contactdish kernel: atapci0: [MPSAFE]
> Feb 26 16:36:26 contactdish kernel: ata0: channel #0 on atapci0
> Feb 26 16:36:26 contactdish kernel: atapci0: Reserved 0x8
> bytes for rid 0x10 type 4 at 0x1f0
> Feb 26 16:36:26 contactdish kernel: atapci0: Reserved 0x1
> bytes for rid 0x14 type 4 at 0x3f6
> Feb 26 16:36:26 contactdish kernel: ata0: reset tp1 mask=00
> ostat0=ff ostat1=ff
> Feb 26 16:36:26 contactdish kernel: ata0: [MPSAFE]
> Feb 26 16:36:26 contactdish kernel: ata1: channel #1 on atapci0
> Feb 26 16:36:26 contactdish kernel: atapci0: Reserved 0x8
> bytes for rid 0x18 type 4 at 0x170
> Feb 26 16:36:26 contactdish kernel: atapci0: Reserved 0x1
> bytes for rid 0x1c type 4 at 0x376
> Feb 26 16:36:26 contactdish kernel: ata1: reset tp1 mask=01
> ostat0=50 ostat1=ff
> Feb 26 16:36:26 contactdish kernel: ata1-master: stat=0x00
> err=0x01 lsb=0x14 msb=0xeb
> Feb 26 16:36:26 contactdish kernel: ata1: reset tp2 stat0=00
> stat1=00 devices=0x4<ATAPI_MASTER>
> Feb 26 16:36:26 contactdish kernel: ata1: [MPSAFE]
> Feb 26 16:36:26 contactdish kernel: ahc0: <Adaptec aic7880
> Ultra SCSI adapter> port 0xfe00-0xfeff mem
> 0xfffdc000-0xfffdcfff irq 10 at device 2.0 on pci0
> Feb 26 16:36:26 contactdish kernel: ahc0: Defaulting to MEMIO off
> Feb 26 16:36:26 contactdish kernel: ahc0: Reserved 0x100 bytes
> for rid 0x10 type 4 at 0xfe00
> Feb 26 16:36:26 contactdish kernel: ahc0: Reading
> SEEPROM...checksum error
> Feb 26 16:36:26 contactdish kernel: ahc0: No SEEPROM available.
> Feb 26 16:36:26 contactdish kernel: ahc0: Using left over BIOS settings
> Feb 26 16:36:26 contactdish kernel: ahc0: Downloading
> Sequencer Program... 442 instructions downloaded
> Feb 26 16:36:26 contactdish kernel: ahc0: Features 0x10001,
> Bugs 0x25, Flags 0x481460
> Feb 26 16:36:26 contactdish kernel: ahc0: [GIANT-LOCKED]
> Feb 26 16:36:26 contactdish kernel: aic7880: Ultra Single
> Channel A, SCSI Id=7, 16/253 SCBs
> Feb 26 16:36:26 contactdish kernel: pci0: <display, VGA> at
> device 11.0 (no driver attached)
> Feb 26 16:36:26 contactdish kernel: fxp0: <Intel 82557 Pro/100
> Ethernet> port 0xffc0-0xffdf mem
> 0xffe00000-0xffefffff,0xfffcc000-0xfffccfff irq 11 at device
> 12.0 on pci0
> Feb 26 16:36:26 contactdish kernel: fxp0: Reserved 0x1000
> bytes for rid 0x10 type 3 at 0xfffcc000
> Feb 26 16:36:26 contactdish kernel: fxp0: using memory space
> register mapping
> Feb 26 16:36:26 contactdish kernel: fxp0: PCI IDs: 8086 1229
> 0000 0000 0001
> Feb 26 16:36:26 contactdish kernel: fxp0: Dynamic Standby mode
> is disabled
> Feb 26 16:36:26 contactdish kernel: miibus0: <MII bus> on fxp0
> Feb 26 16:36:26 contactdish kernel: nsphy0: <DP83840 10/100
> media interface> on miibus0
> Feb 26 16:36:26 contactdish kernel: nsphy0: 10baseT,
> 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> Feb 26 16:36:26 contactdish kernel: fxp0: bpf attached
> Feb 26 16:36:26 contactdish kernel: fxp0: Ethernet address:
> 00:60:b0:1b:e3:9d
> Feb 26 16:36:26 contactdish kernel: fxp0: [MPSAFE]
> Feb 26 16:36:26 contactdish kernel: ahc1: <Adaptec 2940 Ultra
> SCSI adapter> port 0xfd00-0xfdff mem 0xfffbc000-0xfffbcfff irq
> 11 at device 13.0 on pci0
> Feb 26 16:36:26 contactdish kernel: ahc1: Defaulting to MEMIO off
> Feb 26 16:36:26 contactdish kernel: ahc1: Reserved 0x100 bytes
> for rid 0x10 type 4 at 0xfd00
> Feb 26 16:36:26 contactdish kernel: ahc1: Reading SEEPROM...done.
> Feb 26 16:36:26 contactdish kernel: ahc1: internal 50 cable
> not present, internal 68 cable not present
> Feb 26 16:36:26 contactdish kernel: ahc1: external cable is present
> Feb 26 16:36:26 contactdish kernel: ahc1: BIOS eeprom is present
> Feb 26 16:36:26 contactdish kernel: ahc1: High byte termination Enabled
> Feb 26 16:36:26 contactdish kernel: ahc1: Low byte termination Enabled
> Feb 26 16:36:26 contactdish kernel: ahc1: Downloading
> Sequencer Program... 441 instructions downloaded
> Feb 26 16:36:26 contactdish kernel: ahc1: Features 0x10005,
> Bugs 0x11, Flags 0x20481540
> Feb 26 16:36:26 contactdish kernel: ahc1: [GIANT-LOCKED]
> Feb 26 16:36:26 contactdish kernel: aic7880: Ultra Wide
> Channel A, SCSI Id=7, 16/253 SCBs
> Feb 26 16:36:26 contactdish kernel: pci0: <memory, RAM> at
> device 20.0 (no driver attached)
> Feb 26 16:36:26 contactdish kernel: cpu0 on motherboard
> Feb 26 16:36:26 contactdish kernel: cpu1 on motherboard
> Feb 26 16:36:26 contactdish kernel: ata: ata0 already exists;
> skipping it
> Feb 26 16:36:26 contactdish kernel: ata: ata1 already exists;
> skipping it
> Feb 26 16:36:26 contactdish kernel: Trying Read_Port at 203
> Feb 26 16:36:26 contactdish kernel: GDI0031: adding irq mask 0xdea8
> Feb 26 16:36:26 contactdish kernel: GDI0031: adding io range
> 0x200-0x3e7, size=0x8, align=0x20
> Feb 26 16:36:26 contactdish kernel: pnpbios: 17 devices,
> largest 106 bytes
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding io range
> 0x96-0x97, size=0x2, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding io range
> 0x92-0x92, size=0x1, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding io range
> 0xea-0xeb, size=0x2, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding io range
> 0xb2-0xb3, size=0x2, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding io range
> 0x370-0x371, size=0x2, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding fixed
> memory32 range 0-0x9ffff, size=0xa0000
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding fixed
> memory32 range 0x100000-0x17ffffff, size=0x17f00000
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding fixed
> memory32 range 0xf0000-0xfffff, size=0x10000
> Feb 26 16:36:26 contactdish kernel: PNP0c01: adding fixed
> memory32 range 0xffff0000-0xffffffff, size=0x10000
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 0 device
> ID PNP0c01 (010cd041)
> Feb 26 16:36:26 contactdish kernel: PNP0c04: adding irq mask 0x2000
> Feb 26 16:36:26 contactdish kernel: PNP0c04: adding io range
> 0xf0-0xff, size=0x10, align=0
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 1 device
> ID PNP0c04 (040cd041)
> Feb 26 16:36:26 contactdish kernel: PNP0200: adding io range
> 0-0xf, size=0x10, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0200: adding io range
> 0x80-0x91, size=0x12, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0200: adding io range
> 0xc0-0xdf, size=0x20, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0200: adding dma mask 0x10
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 3 device
> ID PNP0200 (0002d041)
> Feb 26 16:36:26 contactdish kernel: PNP0b00: adding io range
> 0x70-0x71, size=0x2, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0b00: adding irq mask 0x100
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 4 device
> ID PNP0b00 (000bd041)
> Feb 26 16:36:26 contactdish kernel: PNP0100: adding io range
> 0x40-0x43, size=0x4, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0100: adding irq mask 0x1
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 5 device
> ID PNP0100 (0001d041)
> Feb 26 16:36:26 contactdish kernel: PNP0800: adding io range
> 0x61-0x61, size=0x1, align=0
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 6 device
> ID PNP0800 (0008d041)
> Feb 26 16:36:26 contactdish kernel: PNPb003: adding irq mask 0x20
> Feb 26 16:36:26 contactdish kernel: PNPb003: adding io range
> 0x220-0x232, size=0x13, align=0
> Feb 26 16:36:26 contactdish kernel: PNPb003: adding dma mask 0x2
> Feb 26 16:36:26 contactdish kernel: PNPb003: adding dma mask 0x20
> Feb 26 16:36:26 contactdish kernel: PNPb003: adding io range
> 0x388-0x38b, size=0x4, align=0
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 7 device
> ID PNPb003 (03b0d041)
> Feb 26 16:36:26 contactdish kernel: PNPb006: adding io range
> 0x330-0x33b, size=0xc, align=0
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 8 device
> ID PNPb006 (06b0d041)
> Feb 26 16:36:26 contactdish kernel: PNP0303: adding io range
> 0x60-0x60, size=0x1, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0303: adding io range
> 0x64-0x64, size=0x1, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0303: adding irq mask 0x2
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 9 device
> ID PNP0303 (0303d041)
> Feb 26 16:36:26 contactdish kernel: PNP0f13: adding irq mask 0x1000
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 10 device
> ID PNP0f13 (130fd041)
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 11 device
> ID PNPb02f (2fb0d041)
> Feb 26 16:36:26 contactdish kernel: PNP0501: adding irq mask 0x10
> Feb 26 16:36:26 contactdish kernel: PNP0501: adding io range
> 0x3f8-0x3ff, size=0x8, align=0
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 12 device
> ID PNP0501 (0105d041)
> Feb 26 16:36:26 contactdish kernel: PNP0501: adding irq mask 0x8
> Feb 26 16:36:26 contactdish kernel: PNP0501: adding io range
> 0x2f8-0x2ff, size=0x8, align=0
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 13 device
> ID PNP0501 (0105d041)
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 14 device
> ID PNP0401 (0104d041)
> Feb 26 16:36:26 contactdish kernel: PNP0700: adding irq mask 0x40
> Feb 26 16:36:26 contactdish kernel: PNP0700: adding io range
> 0x3f0-0x3f5, size=0x6, align=0
> Feb 26 16:36:26 contactdish kernel: PNP0700: adding dma mask 0x4
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 15 device
> ID PNP0700 (0007d041)
> Feb 26 16:36:26 contactdish kernel: PNP0a03: adding io range
> 0xcf8-0xcff, size=0x8, align=0
> Feb 26 16:36:26 contactdish kernel: pnpbios: handle 16 device
> ID PNP0a03 (030ad041)
> Feb 26 16:36:26 contactdish kernel: unknown: status reg test failed fe
> Feb 26 16:36:26 contactdish kernel: unknown: status reg test failed ff
> Feb 26 16:36:26 contactdish last message repeated 4 times
> Feb 26 16:36:26 contactdish kernel: sc: sc0 already exists; skipping it
> Feb 26 16:36:26 contactdish kernel: vga: vga0 already exists;
> skipping it
> Feb 26 16:36:26 contactdish kernel: isa_probe_children:
> disabling PnP devices
> Feb 26 16:36:26 contactdish kernel: isa_probe_children:
> probing non-PnP devices
> Feb 26 16:36:26 contactdish kernel: orm0: <ISA Option ROMs> at
> iomem 0xd0000-0xd47ff,0xc8000-0xcffff,0xc0000-0xc7fff on isa0
> Feb 26 16:36:26 contactdish kernel: pmtimer0 on isa0
> Feb 26 16:36:26 contactdish kernel: adv0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: aha0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: aic0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: atkbdc0: <Keyboard
> controller (i8042)> at port 0x64,0x60 on isa0
> Feb 26 16:36:26 contactdish kernel: atkbd0: <AT Keyboard>
> flags 0x1 irq 1 on atkbdc0
> Feb 26 16:36:26 contactdish kernel: atkbd: the current kbd
> controller command byte 0065
> Feb 26 16:36:26 contactdish kernel: atkbd: keyboard ID 0x41ab (2)
> Feb 26 16:36:26 contactdish kernel: kbd0 at atkbd0
> Feb 26 16:36:26 contactdish kernel: kbd0: atkbd0, AT 101/102
> (2), config:0x1, flags:0x3d0000
> Feb 26 16:36:26 contactdish kernel: atkbd0: [GIANT-LOCKED]
> Feb 26 16:36:26 contactdish kernel: psm0: current command byte:0065
> Feb 26 16:36:26 contactdish kernel: psm0: <PS/2 Mouse> irq 12
> on atkbdc0
> Feb 26 16:36:26 contactdish kernel: psm0: [GIANT-LOCKED]
> Feb 26 16:36:26 contactdish kernel: psm0: model IntelliMouse,
> device ID 3-00, 3 buttons
> Feb 26 16:36:26 contactdish kernel: psm0: config:00000000,
> flags:00000008, packet size:4
> Feb 26 16:36:26 contactdish kernel: psm0: syncmask:08, syncbits:00
> Feb 26 16:36:26 contactdish kernel: bt0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: cs0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: ed0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: fdc0: ic_type 90 part_id 80
> Feb 26 16:36:26 contactdish kernel: fdc0: <Enhanced floppy
> controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
> Feb 26 16:36:26 contactdish kernel: fdc0: ic_type 90 part_id 80
> Feb 26 16:36:26 contactdish kernel: fdc0: [MPSAFE]
> Feb 26 16:36:26 contactdish kernel: fdc0: [FAST]
> Feb 26 16:36:26 contactdish kernel: fd0: <1440-KB 3.5" drive>
> on fdc0 drive 0
> Feb 26 16:36:26 contactdish kernel: fe0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: ie0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: lnc0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: pcic0 failed to probe at
> port 0x3e0 iomem 0xd0000 on isa0
> Feb 26 16:36:26 contactdish kernel: pcic1: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: ppc0: parallel port not found.
> Feb 26 16:36:26 contactdish kernel: ppc0: <Parallel port>
> failed to probe at irq 7 on isa0
> Feb 26 16:36:26 contactdish kernel: sc0: <System console> at
> flags 0x100 on isa0
> Feb 26 16:36:26 contactdish kernel: sc0: VGA <16 virtual
> consoles, flags=0x300>
> Feb 26 16:36:26 contactdish kernel: sc0: fb0, kbd0, terminal
> emulator: sc (syscons terminal)
> Feb 26 16:36:26 contactdish kernel: sio0: irq maps: 0x8081
> 0x8091 0x8081 0x8081
> Feb 26 16:36:26 contactdish kernel: sio0 at port 0x3f8-0x3ff
> irq 4 flags 0x10 on isa0
> Feb 26 16:36:26 contactdish kernel: sio0: type 16550A
> Feb 26 16:36:26 contactdish kernel: sio1: irq maps: 0x8081
> 0x8089 0x8081 0x8081
> Feb 26 16:36:26 contactdish kernel: sio1 at port 0x2f8-0x2ff
> irq 3 on isa0
> Feb 26 16:36:26 contactdish kernel: sio1: type 16550A
> Feb 26 16:36:26 contactdish kernel: sio2: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: sio3: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: sn0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: vga0: <Generic ISA VGA> at
> port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Feb 26 16:36:26 contactdish kernel: fb0: vga0, vga, type:VGA
> (5), flags:0x7007f
> Feb 26 16:36:26 contactdish kernel: fb0: port:0x3c0-0x3df,
> crtc:0x3d4, mem:0xa0000 0x20000
> Feb 26 16:36:26 contactdish kernel: fb0: init mode:24, bios
> mode:3, current mode:24
> Feb 26 16:36:26 contactdish kernel: fb0: window:0xc00b8000
> size:32k gran:32k, buf:0 size:32k
> Feb 26 16:36:26 contactdish kernel: VGA parameters upon power-up
> Feb 26 16:36:26 contactdish kernel: 50 18 10 00 00 00 03 00 02
> 67 60 4f 50 83 55 81
> Feb 26 16:36:26 contactdish kernel: bf 1f 00 4f 0d 0e 00 00 07
> 80 9c 8e 8f 28 1f 96
> Feb 26 16:36:26 contactdish kernel: b9 a3 ff 00 01 02 03 04 05
> 14 07 38 39 3a 3b 3c
> Feb 26 16:36:26 contactdish kernel: 3d 3e 3f 0c 00 0f 08 00 00
> 00 00 00 10 0e 00 ff
> Feb 26 16:36:26 contactdish kernel: VGA parameters in BIOS for mode 24
> Feb 26 16:36:26 contactdish kernel: 50 18 10 00 10 00 03 00 02
> 67 60 4f 50 83 55 81
> Feb 26 16:36:26 contactdish kernel: bf 1f 00 4f 0d 0e 00 00 00
> 00 9c 8e 8f 28 1f 96
> Feb 26 16:36:26 contactdish kernel: b9 a3 ff 00 01 02 03 04 05
> 14 07 38 39 3a 3b 3c
> Feb 26 16:36:26 contactdish kernel: 3d 3e 3f 0c 00 0f 08 00 00
> 00 00 00 10 0e 00 ff
> Feb 26 16:36:26 contactdish kernel: EGA/VGA parameters to be
> used for mode 24
> Feb 26 16:36:26 contactdish kernel: 50 18 10 00 10 00 03 00 02
> 67 60 4f 50 83 55 81
> Feb 26 16:36:26 contactdish kernel: bf 1f 00 4f 0d 0e 00 00 00
> 00 9c 8e 8f 28 1f 96
> Feb 26 16:36:26 contactdish kernel: b9 a3 ff 00 01 02 03 04 05
> 14 07 38 39 3a 3b 3c
> Feb 26 16:36:26 contactdish kernel: 3d 3e 3f 0c 00 0f 08 00 00
> 00 00 00 10 0e 00 ff
> Feb 26 16:36:26 contactdish kernel: vt0: not probed (disabled)
> Feb 26 16:36:26 contactdish kernel: isa_probe_children:
> probing PnP devices
> Feb 26 16:36:26 contactdish kernel: unknown: <G.Diehl ISDN
> (EICON Technology) DIVA Pro> failed to probe at port
> 0x200-0x207 irq 5 on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0800> failed
> to probe at port 0x61 on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNPb003> can't
> assign resources (irq)
> Feb 26 16:36:26 contactdish kernel: unknown: <PNPb003> at port
> 0x388-0x38b,0x220-0x232 irq 5 on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNPb006> failed
> to probe at port 0x330-0x33b on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0303> can't
> assign resources (port)
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0303> at port
> 0x60 on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0f13> can't
> assign resources (irq)
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0f13> at irq
> 12 on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNPb02f> failed
> to probe on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0501> can't
> assign resources (port)
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0501> at port
> 0x3f8-0x3ff on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0501> can't
> assign resources (port)
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0501> at port
> 0x2f8-0x2ff on isa0
> Feb 26 16:36:26 contactdish kernel: ppc1: parallel port not found.
> Feb 26 16:36:26 contactdish kernel: unknown: <ECP parallel
> printer port> failed to probe on isa0
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0700> can't
> assign resources (port)
> Feb 26 16:36:26 contactdish kernel: unknown: <PNP0700> at port
> 0x3f0-0x3f5 on isa0
> Feb 26 16:36:26 contactdish kernel: Device configuration finished.
> Feb 26 16:36:26 contactdish kernel: procfs registered
> Feb 26 16:36:26 contactdish kernel: Timecounter "TSC"
> frequency 195744728 Hz quality -100
> Feb 26 16:36:26 contactdish kernel: Timecounters tick every 10.000 msec
> Feb 26 16:36:26 contactdish kernel: lo0: bpf attached
> Feb 26 16:36:26 contactdish kernel: ata1-master: pio=0x0b
> wdma=0x21 udma=0xffffffff cable=40pin
> Feb 26 16:36:26 contactdish kernel: ata1-master: setting PIO3
> on CMD 646 chip
> Feb 26 16:36:26 contactdish kernel: acd0: <HITACHI
> CDR-7930/1023> CDROM drive at ata1 as master
> Feb 26 16:36:26 contactdish kernel: acd0: read 1377KB/s
> (1377KB/s), 128KB buffer, PIO3
> Feb 26 16:36:26 contactdish kernel: acd0: Reads: CDDA
> Feb 26 16:36:26 contactdish kernel: acd0: Writes:
> Feb 26 16:36:26 contactdish kernel: acd0: Audio: play, 255
> volume levels
> Feb 26 16:36:26 contactdish kernel: acd0: Mechanism: ejectable
> tray, unlocked
> Feb 26 16:36:26 contactdish kernel: acd0: Medium: CD-ROM 120mm
> data disc
> Feb 26 16:36:26 contactdish kernel: Waiting 15 seconds for
> SCSI devices to settle
> Feb 26 16:36:26 contactdish kernel: (noperiph:ahc0:0:-1:-1):
> SCSI bus reset delivered. 0 SCBs aborted.
> Feb 26 16:36:26 contactdish kernel: (noperiph:ahc1:0:-1:-1):
> SCSI bus reset delivered. 0 SCBs aborted.
> Feb 26 16:36:26 contactdish kernel: [0] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: [1] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: [2] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: [3] f:80 typ:165
> s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure fd0a,
> start 0 length 1474560 end 1474559
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure fd0c,
> start 0 length 1474560 end 1474559
> Feb 26 16:36:26 contactdish kernel: ahc0: Selection Timeout on
> A:3. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:0. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc0: Selection Timeout on
> A:4. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:3. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc0: Selection Timeout on
> A:6. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:6. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc0: Selection Timeout on
> A:1. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:8. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:11. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc0: Selection Timeout on
> A:5. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: (probe0:ahc0:0:0:0):
> Retrying Command
> Feb 26 16:36:26 contactdish kernel: (probe2:ahc0:0:2:0):
> Retrying Command
> Feb 26 16:36:26 contactdish kernel: (ahc0:A:0:0): Sending SDTR
> period 19, offset f
> Feb 26 16:36:26 contactdish kernel: (ahc0:A:0:0): Received
> SDTR period 19, offset f
> Feb 26 16:36:26 contactdish kernel: Filtered to period 19, offset f
> Feb 26 16:36:26 contactdish kernel: ahc0: target 0 synchronous
> at 10.0MHz, offset = 0xf
> Feb 26 16:36:26 contactdish kernel: (ahc0:A:2:0): Sending SDTR
> period c, offset f
> Feb 26 16:36:26 contactdish kernel: (ahc0:A:2:0): Received
> SDTR period c, offset f
> Feb 26 16:36:26 contactdish kernel: Filtered to period c, offset f
> Feb 26 16:36:26 contactdish kernel: ahc0: target 2 synchronous
> at 20.0MHz, offset = 0xf
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:14. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:15. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:1. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:2. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:4. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:5. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:9. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:10. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:12. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: ahc1: Selection Timeout on
> A:13. 0 SCBs aborted
> Feb 26 16:36:26 contactdish kernel: pass0 at ahc0 bus 0 target 0 lun 0
> Feb 26 16:36:26 contactdish kernel: pass0: <SEAGATE ST15150N
> 0023> Fixed Direct Access SCSI-2 device
> Feb 26 16:36:26 contactdish kernel: pass0: Serial Number 02763783
> Feb 26 16:36:26 contactdish kernel: pass0: 10.000MB/s
> transfers (10.000MHz, offset 15), Tagged Queueing Enabled
> Feb 26 16:36:26 contactdish kernel: pass1 at ahc0 bus 0 target 2 lun 0
> Feb 26 16:36:26 contactdish kernel: pass1: <QUANTUM XP34550S
> LXY1> Fixed Direct Access SCSI-2 device
> Feb 26 16:36:26 contactdish kernel: pass1: Serial Number
> PCB=2011303001 ; HDA=184630912701
> Feb 26 16:36:26 contactdish kernel: pass1: 20.000MB/s
> transfers (20.000MHz, offset 15), Tagged Queueing Enabled
> Feb 26 16:36:26 contactdish kernel: da0 at ahc0 bus 0 target 0 lun 0
> Feb 26 16:36:26 contactdish kernel: da0: <SEAGATE ST15150N
> 0023> Fixed Direct Access SCSI-2 device
> Feb 26 16:36:26 contactdish kernel: da0: Serial Number 02763783
> Feb 26 16:36:26 contactdish kernel: da0: 10.000MB/s transfers
> (10.000MHz, offset 15), Tagged Queueing Enabled
> Feb 26 16:36:26 contactdish kernel: da0: 4095MB (8388315 512
> byte sectors: 64H 32S/T 4095C)
> Feb 26 16:36:26 contactdish kernel: da1 at ahc0 bus 0 target 2 lun 0
> Feb 26 16:36:26 contactdish kernel: da1: <QUANTUM XP34550S
> LXY1> Fixed Direct Access SCSI-2 device
> Feb 26 16:36:26 contactdish kernel: da1: Serial Number
> PCB=2011303001 ; HDA=184630912701
> Feb 26 16:36:26 contactdish kernel: da1: 20.000MB/s transfers
> (20.000MHz, offset 15), Tagged Queueing Enabled
> Feb 26 16:36:26 contactdish kernel: da1: 4341MB (8890760 512
> byte sectors: 64H 32S/T 4341C)
> Feb 26 16:36:26 contactdish kernel: GEOM: new disk da0
> Feb 26 16:36:26 contactdish kernel: GEOM: new disk da1
> Feb 26 16:36:26 contactdish kernel: SMP: AP CPU #1 Launched!
> Feb 26 16:36:26 contactdish kernel: cpu1 AP:
> Feb 26 16:36:26 contactdish kernel: ID: 0x00000000 VER:
> 0x00040011 LDR: 0x01000000 DFR: 0x0fffffff
> Feb 26 16:36:26 contactdish kernel: lint0: 0x00010700 lint1:
> 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 1
> (ISA IRQ 1) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 3
> (ISA IRQ 3) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 4
> (ISA IRQ 4) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 6
> (ISA IRQ 6) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 8
> (ISA IRQ 8) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 10
> (ISA IRQ 10) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 11
> (ISA IRQ 11) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 12
> (ISA IRQ 12) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 13
> (ISA IRQ 13) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 14
> (ISA IRQ 14) to cluster 0
> Feb 26 16:36:26 contactdish kernel: ioapic0: routing intpin 15
> (ISA IRQ 15) to cluster 0
> Feb 26 16:36:26 contactdish kernel: [0] f:00 typ:165
> s(CHS):0/1/1 e(CHS):1023/63/32 s:32 l:8386528
> Feb 26 16:36:26 contactdish kernel: [1] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: [2] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: [3] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da0s1,
> start 16384 length 4293902336 end 4293918719
> Feb 26 16:36:26 contactdish kernel: [0] f:80 typ:165
> s(CHS):0/1/1 e(CHS):1023/63/32 s:32 l:8890336
> Feb 26 16:36:26 contactdish kernel: [1] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: [2] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: [3] f:00 typ:0
> s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da1s1,
> start 16384 length 4551852032 end 4551868415
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da0s1a,
> start 0 length 2621440000 end 2621439999
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da0s1b,
> start 2621440000 length 805306368 end 3426746367
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da0s1c,
> start 0 length 4293902336 end 4293902335
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da0s1d,
> start 3426746368 length 433061888 end 3859808255
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da0s1e,
> start 3859808256 length 434094080 end 4293902335
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da1s1c,
> start 0 length 4551852032 end 4551852031
> Feb 26 16:36:26 contactdish kernel: GEOM: Configure da1s1d,
> start 0 length 4551852032 end 4551852031
> Feb 26 16:36:26 contactdish kernel: Mounting root from ufs:/dev/da0s1a
> Feb 26 16:36:26 contactdish kernel: start_init: trying /sbin/init
>
> --
> Anthony
>
> --
> Anthony
>
>
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to
> "freebsd-questions-unsubscribe at freebsd.org"
>
More information about the freebsd-questions
mailing list