6.0-R, ICH6 and SATA problems
bcsfd204 at twcny.rr.com
bcsfd204 at twcny.rr.com
Sat Dec 31 14:57:56 PST 2005
Hi.
I'm running 6.0-R on a Shuttle SB95P V2 that is using the ICH6 and
SATA150 disks.
I'm getting recurring failures that either hang the machine or cause a
reboot.
The following messages appear to be common to all of the failures.
Typos are mine. :-)
ata2 disconnect requested
ar0 Failure - RAID0 array broken
ar0 Writing of Intel MatrixRAID metadata is NOT supported yet
subdisk4: detached
ad4: Detatched
ata2: DISCONNECTED
I dug around the mailing list archives but I could not find something
that seemed to match what I'm seeing.
The machine has gotten to the point where it hangs about half way
through startup of KDE. (Sometimes, CNTL-ALT-BACKSPACE will break it
and force an automatic reboot.)
I have replaced both hard drives with no change.
The disk controller is on the mother board so I switched the SATA leads
from master to slave and back again with no change.
I'm not sure where to go with this.
The man pages seem to indicate the ICH6 chip is supported.
The notations on read/write vs read-only support for Intel MatrixRAID
leave me confused given the message "ar0 Writing of Intel MatrixRAID
metadata is NOT supported yet".
It's possible I did something wrong in the CMOS setup (there was
comments in the man pages that I didn't understand about CMOS vormat vs
formatting with ATACONTROL.)
I'm attaching the usual DOC.
TIA for any help you can provide.
FreeBSD stargate.parquette.lan 6.0-RELEASE FreeBSD 6.0-RELEASE #2: Wed
Nov 16 19:56:14 EST 2005
admin at stargate.parquette.lan:/usr/obj/usr/src/sys/STARGATE i386
ATA channel 0:
Master: acd0 <PLEXTOR DVDR PX-716A/1.06> ATA/ATAPI revision 6
Slave: no device present
ATA channel 1:
Master: no device present
Slave: no device present
ATA channel 2:
Master: ad4 <ST3120827AS/3.42> Serial ATA v1.0
Slave: no device present
ATA channel 3:
Master: ad6 <ST3120827AS/3.42> Serial ATA v1.0
Slave: no device present
ATA channel 4:
Master: no device present
Slave: no device present
ATA channel 5:
Master: no device present
Slave: no device present
The following dmesg was taken after a reboot following one of the
failures. That is why it is complaining about the filesystems not
being demounted.
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD 6.0-RELEASE #2: Wed Nov 16 19:56:14 EST 2005
admin at stargate.parquette.lan:/usr/obj/usr/src/sys/STARGATE
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) CPU 2.66GHz (2672.74-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf41 Stepping = 1
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE
,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x451d<SSE3,RSVD2,MON,DS_CPL,TM2,CNTX-ID,<b14>>
AMD Features=0x100000<NX>
real memory = 2147418112 (2047 MB)
avail memory = 2096594944 (1999 MB)
ACPI APIC Table: <XPC AWRDACPI>
ioapic0 <Version 2.0> irqs 0-23 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <XPC AWRDACPI> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 10 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 0 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 5 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 11 on acpi0
pci_link4: <ACPI PCI Link LNKE> irq 0 on acpi0
pci_link5: <ACPI PCI Link LNKF> irq 0 on acpi0
pci_link6: <ACPI PCI Link LNK0> irq 0 on acpi0
pci_link7: <ACPI PCI Link LNK1> irq 3 on acpi0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pci1: <display> at device 0.1 (no driver attached)
pci0: <multimedia> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bge0: <Broadcom BCM5751 Gigabit Ethernet, ASIC rev. 0x4001> mem
0xd8100000-0xd810ffff irq 16 at device 0.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: Ethernet address: 00:30:1b:b7:e0:00
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port
0xe300-0xe31f irq 23 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port
0xe000-0xe01f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port
0xe100-0xe11f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port
0xe200-0xe21f irq 16 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xd8304000-0xd83043ff
irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
umass0: USB2.0 CardReader, rev 2.00/91.44, addr 2
pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci3: <ACPI PCI bus> on pcib3
fwohci0: <VIA Fire II (VT6306)> port 0xd000-0xd07f mem 0xd8200000-
0xd82007ff irq 18 at device 10.0 on pci3
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:30:1b:b7:00:00:e0:64
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:30:1b:00:e0:64
fwe0: Ethernet address: 02:30:1b:00:e0:64
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-
0x177,0x376,0xf000-0xf00f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH6 SATA150 controller> port 0xe400-0xe407,0xe500-
0xe503,0xe600-0xe607,0xe700-0xe703,0xe800-0xe80f mem 0xd8305000-
0xd83053ff irq 19 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
ata4: <ATA channel 2> on atapci1
ata5: <ATA channel 3> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcbfff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
Timecounter "TSC" frequency 2672744460 Hz quality 800
Timecounters tick every 1.000 msec
acd0: DVDR <PLEXTOR DVDR PX-716A/1.06> at ata0-master UDMA66
ad4: 114473MB <Seagate ST3120827AS 3.42> at ata2-master SATA150
ad4: Intel calc=b2613236 meta=5930991b
ad6: 114473MB <Seagate ST3120827AS 3.42> at ata3-master SATA150
ad6: Intel calc=b2613236 meta=5930991b
ar0: 228946MB <Intel MatrixRAID RAID0 (stripe 128 KB)> status: READY
ar0: disk0 READY using ad4 at ata2-master
ar0: disk1 READY using ad6 at ata3-master
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <USB2.0 CF CardReader 9144> Removable Direct Access SCSI-0 device
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
da1 at umass-sim0 bus 0 target 0 lun 1
da1: <USB2.0 CBO CardReader 9144> Removable Direct Access SCSI-0 device
da1: 40.000MB/s transfers
da1: Attempt to query device size failed: NOT READY, Medium not present
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI Status: Check Condition
(da0:umass-sim0:0:0:0): NOT READY asc:3a,0
(da0:umass-sim0:0:0:0): Medium not present
(da0:umass-sim0:0:0:0): Unretryable error
Opened disk da0 -> 6
(da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0
(da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:1): SCSI Status: Check Condition
(da1:umass-sim0:0:0:1): NOT READY asc:3a,0
(da1:umass-sim0:0:0:1): Medium not present
(da1:umass-sim0:0:0:1): Unretryable error
Opened disk da1 -> 6
(da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0
(da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:1): SCSI Status: Check Condition
(da1:umass-sim0:0:0:1): NOT READY asc:3a,0
(da1:umass-sim0:0:0:1): Medium not present
(da1:umass-sim0:0:0:1): Unretryable error
Opened disk da1 -> 6
(da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0
(da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:1): SCSI Status: Check Condition
(da1:umass-sim0:0:0:1): NOT READY asc:3a,0
(da1:umass-sim0:0:0:1): Medium not present
(da1:umass-sim0:0:0:1): Unretryable error
Opened disk da1 -> 6
Trying to mount root from ufs:/dev/ar0s1a
WARNING: / was not properly dismounted
WARNING: /home was not properly dismounted
/home: mount pending error: blocks 12 files 4
WARNING: /local was not properly dismounted
WARNING: /tmp was not properly dismounted
WARNING: /usr was not properly dismounted
WARNING: /var was not properly dismounted
More information about the freebsd-questions
mailing list