Connecting ISP problem

[Stephen Liu]

Hi JJB,

Tks for your advice.

>This is wrong.
>++++++++++++++++ is not comment or command    remove it.
>You have all statements starting in position 1 this is
>wrong, section header names start in position 1 and end with :
>
>default:   and    dialisp:
>
>
>make ppp.conf look like this
>default: & dialisp: start in position 1 and
>everything else starts in position 2
>delete all the other stuff you have in your ppp.conf.
>
>default:
> set log Phase tun             #use to avoid excessive log sizes
> set timeout 0      # no idle time out, will not disconnect
>
>dialisp:
> set device PPPoE:rl0          # replace xxx with your Nic device
>name
> set authname YOURLOGINNAME    # Replace with your ISP account IP
> set authkey YOURPASSWORD     # Replace with your ISP account PW
> add default HISADDR        # Add a (sticky) default route Mandatory
> enable dns      # Gets the ISP's DNS IP address & places them
>                 # in resolv.conf for reference by FBSD box
>
>
>In rc.conf you have
>ifconfig-rl0=up
>
>and it should be
>
>ifconfig_rl0=up
>
>hostname="localhost" is wrong it needs to be FQDN
>as in hostname="fbsdstephenliu.com.hk"
>
>check /etc/syslog.conf and make sure ppp.log is enabled.
>Empty ppp.log before test and
>post ppp.log if this does not work.
>

Now ISP connected but failure to connect Internet.  Tried twice

# ifconfig

rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    options=8<VLAN_MTU>
    inet6 fe80::250:fcff:fe61:f394%rl0 prefixlen 64 scopeid 0x1
    inet 192.168.2.2 netmask 0xffffff00 broadcast 192.168.2.255
    ether 00:50:fc:61:f3:94
    media: Ethernet autoselect (10baseT/UTP)
    status: active
rl1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
    options=8<VLAN_MTU>
    ether 00:50:fc:6c:70:f7
    media: Ethernet autoselect (10baseT/UTP)
    status: no carrier
plip0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
    inet 127.0.0.1 netmask 0xff000000
    inet6 ::1 prefixlen 128
    inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1492
    inet 203.88.164.90 --> 203.88.164.1 netmask 0xffffffff
    Opened by PID 236


# ping -c 3 [url]www.google.com[/url]
ping: cannot resolve [url]www.google.com:[/url] Host name lookup failure.


Tried follows without success;
# /sbin/route add default gw 203.88.164.1 dev tun0
# /sbin/route add default gw 203.88.164.1 dev ppp0
# /sbin/route add default gw 203.88.164.1 dev pppoe

all hanged on screen


# cat /var/log/ppp.log
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Received 
NGM_PPPOE_ACNAME (hook "TSW3-2-RX")
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Received 
NGM_PPPOE_SESSIONID
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Received NGM_PPPOE_SUCCESS
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: carrier -> login
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: login -> lcp
Feb 27 07:56:39 localhost ppp[236]: tun0: Warning: deflink: Reducing 
configured MRU from 1500 to 1492
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: bundle: Authenticate
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: his = PAP, 
mine = none
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Pap Output: 
[email]satimis at icare.com.hk[/email] ********
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: Pap Input: SUCCESS ()
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: lcp -> open
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: bundle: Network
Feb 27 07:56:39 localhost ppp[236]: tun0: Phase: deflink: IPV6CP 
protocol reject closes IPV6CP !
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: Received 
NGM_PPPOE_ACNAME (hook "TSW3-2-RX")
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: Received 
NGM_PPPOE_SESSIONID
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: Received NGM_PPPOE_SUCCESS
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: deflink: carrier -> login
Feb 27 08:05:30 localhost ppp[236]: tun0: Phase: deflink: login -> lcp
Feb 27 08:05:30 localhost ppp[236]: tun0: Warning: deflink: Reducing 
configured MRU from 1500 to 1492
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: bundle: Authenticate
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: deflink: his = PAP, 
mine = none
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: Pap Output: 
[email]satimis at icare.com.hk[/email] ********
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: Pap Input: SUCCESS ()
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: deflink: lcp -> open
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: bundle: Network
Feb 27 08:05:31 localhost ppp[236]: tun0: Phase: deflink: IPV6CP 
protocol reject closes IPV6CP !


# cat /etc/rc.conf
inetd_enable="YES"
keymap="us.pc-ctrl"
linux_enable="YES"
sshd_enable="YES"
usbd_enable="YES"

ifconfig_rl0="up"
ifconfig_rl0="DHCP"
# ppp_enable="YES"

# Activate user ppp auto-start at boot time
ppp_enable="YES"    # Start User ppp task
ppp_mode="ddial"    # ddial, auto, background
ppp_profile="dialisp":    # Section in ppp.conf to exec


# cat /etc/ppp/ppp.conf
[code]
default:
 set log phase tun
 set timeout 0
dialisp::
 set device pppoe:rl0
 set authname [email]satimis at icare.com.hk[/email]
 set authkey msliu20h
 add default HISADDR
# (mandatory)
 enable dns


'dialisp::' is correct
'dialisp:' complained as follow;
dialisp:: Configuration lable not found

B.R.
Stephen