TV Tuner Card support under FreeBSD

[Ruslan N. Gogunsci]

Hello freebsd-multimedia,
On Sat, Nov 06, 2004 at 01:21:40AM -0800, Aaron Walker wrote:
> I'm getting some mixed signals on which TV Tuner cards are supported.
> First I see that only the BrookTree chipset is supported, but then I
> see references to Phillips chipset tuners in the manual. I have access
> to two tv tuner cards, one a VisionTek Xtasy Everything (Geforce 2 MX
> 400 64M ViVo) and the other an ATI All In Wonder 128 (Rage 128 chipset
> 16M). Obviously the Xtasy is the better card, but are either of these
> supported under FreeBSD for TV Tuning, or would I be better off just
> leaving these two for some other flavor of Multimedia box?
I have tv tuner based on saa7134HL: Behold TV 403 fm
I try use for it drivers from download.purple.com
They are install without errors, but when i run programs for
watch tv(tvv, ftvv) i see only black screen. I generate
channel list by tune_channels and try convert from xawtv.

My system is 5.3RC1
pciconf -lv:
-skip-
saa0 at pci0:11:0: class=0x048000 card=0x00001131 chip=0x71341131 rev=0x01
hdr=0x00
    vendor   = 'Philips Semiconductors'
    device   = 'SAA7134HL Multi Media Capture Device'
    class    = multimedia
-skip
dmesg:
-skip-
aa0: <Phillips SAA7134 AV broadcast decoder> mem 0xef001000-0xef0013ff
irq 10 at device 11.0 on pci0
saa0: [GIANT-LOCKED]
iicbus0: <SAA713x I2C Controller> on saa0
iic0: <I2C generic I/O> on iicbus0
iicsmb0: <SMBus over I2C bridge> on iicbus0
smbus1: <System Management Bus> on iicsmb0
smb1: <SMBus generic I/O> on smbus1
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: START: bus error (status 0x9 loop:13)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: WRITE: timeout (status 0x6)
iicbus0: WRITE: timeout (status 0x6)
-skip-

> 
> Aaron Walker
> Fairview, OR
> _______________________________________________
> freebsd-multimedia at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-multimedia
> To unsubscribe, send any mail to "freebsd-multimedia-unsubscribe at freebsd.org"