Logitech Wingman Attack joystick

Alex Teslik alex at acatysmoof.com
Mon May 5 23:03:01 PDT 2003

Hi Mat,

     Sorry to inundate you with output. This output is a little different
since the last because I re-compiled pcm support out of my kernel, rebooted,
and loaded the modules as follows:

[alex]/home/alex# kldload -v joy
Loaded joy, id=4

[alex]/home/alex# kldload -v snd_pcm
Loaded snd_pcm, id=5

[alex]/home/alex# pciconf -lv
none2 at pci0:12:0:        class=0x040100 card=0x80611102 chip=0x00021102
rev=0x07 hdr=0x00
    vendor   = 'Creative Labs'
    device   = 'EMU10K1 Audio Chipset (SB Live!)'
    class    = multimedia
    subclass = audio
none3 at pci0:12:1:        class=0x098000 card=0x00201102 chip=0x70021102
rev=0x07 hdr=0x00
    vendor   = 'Creative Labs'
    device   = 'PCI Gameport Joystick'
    class    = input device

[alex]/home/alex# kldstat -v
 4    1 0xc3053000 3000     joy.ko
        Contains modules:
                Id Name
                99 isa/joy
                100 pci/joy
 5    1 0xc305a000 14000    snd_pcm.ko
        Contains modules:
                Id Name
                101 snd_pcm

[alex]/home/alex# dmesg
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.8-RELEASE #3: Mon May  5 22:42:20 PDT 2003
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel(R) Pentium(R) III CPU family      1266MHz (1266.25-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6b1  Stepping = 1
real memory  = 1610612736 (1572864K bytes)
avail memory = 1564110848 (1527452K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
 cpu0 (BSP): apic id:  0, version: 0x00040011, at 0xfee00000
 cpu1 (AP):  apic id:  1, version: 0x00040011, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x00178011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc03b3000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03b309c.
netsmb_dev: loaded
Pentium Pro MTRR support enabled
Using $PIR table, 8 entries at 0xc00fdc70
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 15 -> irq 2
IOAPIC #0 intpin 11 -> irq 5
IOAPIC #0 intpin 5 -> irq 10
IOAPIC #0 intpin 10 -> irq 11
pci0: <PCI bus> on pcib0
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xf0000000-0xf3ffffff
at device 0.0 on pci0
pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0xd000-0xd00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 2 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 2 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x1106, dev=0x3057) at 7.4
ahc0: <Adaptec 2940A Ultra SCSI adapter> port 0xdc00-0xdcff mem
0xf7000000-0xf7000fff irq 5 at device 8.0 on pci0
aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
pci0: <NVidia Riva TNT graphics accelerator> at 9.0 irq 10
ahc1: <Adaptec 2902/04/10/15/20/30C SCSI adapter> port 0xe000-0xe0ff mem
0xf7001000-0xf7001fff irq 2 at device 10.0 on pci0
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xe400-0xe47f mem
0xf7002000-0xf700207f irq 11 at device 11.0 on pci0
xl0: Ethernet address: 00:50:da:1a:12:c6
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=0x1102, dev=0x0002) at 12.0 irq 5
pci0: <unknown card> (vendor=0x1102, dev=0x7002) at 12.1
orm0: <Option ROMs> at iomem 0xc0000-0xc87ff,0xcc000-0xd07ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE
Probing for PnP devices on ppbus0:
ppbus0: <EPSON Stylus Photo 870> PRINTER ESCPL2,BDC,D4
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
ad0: 76319MB <WDC WD800JB-00CRA1> [155061/16/63] at ata0-master UDMA100
Waiting 5 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 1 lun 0
da0: <IBM DGHS09Y 03E0> Fixed Direct Access SCSI-3 device 
da0: 20.000MB/s transfers (20.000MHz, offset 15)
da0: 8748MB (17916240 512 byte sectors: 255H 63S/T 1115C)
cd0 at ahc0 bus 0 target 0 lun 0
cd0: <Traxdata CDR4120 5.0R> Removable CD-ROM SCSI-2 device 
cd0: 10.000MB/s transfers (10.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present

xmame does not recognize it - same error message as before.

This also appeared in /var/log/messages after loading the joy module:
device_probe_and_attach: joy0 attach returned 6

I don't know what that means unfortunately. :/
Let me know if there is any other information you need or anything else I can do.


---------- Original Message -----------
From: Mathew Kanner <mat at cnd.mcgill.ca>
To: Alex Teslik <alex at acatysmoof.com>
Sent: Tue, 6 May 2003 01:24:08 -0400
Subject: Re: Logitech Wingman Attack joystick

> On May 06, Alex Teslik wrote:
> > ...
> 	Another thought.  The new joy module has to be loaded *before*
> the sound driver.
> 	--Mat
> -- 
> Brain: Are you pondering what I'm pondering?
> Pinky: Uh... yeah, Brain, but where will we get rubber pants our size?
------- End of Original Message -------

More information about the freebsd-multimedia mailing list