Solve: AR7161 USB

[Adrian Chadd]

Well, there are board specific config and hints files for this reason. :)

Other boards have specific config/hints files that are to enable USB.
This happens way too frequently :(



-adrian


On 2 October 2016 at 16:41, Mori Hiroki <yamori813 at yahoo.co.jp> wrote:
> Hi.
>
> I add this setting to rc script to WZR-HP-AG300H at ZRouter
> build system.
>
> I think sys/mips/conf have only soc base setting. Because of
> soc and board setting is very scrambled. It is hard find target
> setting. We are never correct all world board setting.
>
> Regards
>
> Hiroki Mori
>
>
> ----- Original Message -----
>> From: Adrian Chadd <adrian.chadd at gmail.com>
>> To: Mori Hiroki <yamori813 at yahoo.co.jp>
>> Cc: "freebsd-mips at freebsd.org" <freebsd-mips at freebsd.org>
>> Date: 2016/9/30, Fri 06:41
>> Subject: Re: Solve: AR7161 USB
>>
>> Cool. There's some stuff you can put in hints to set on/off gpio
>> functions. Can you provide a diff to the right .hints file so it's
>> done at boot time?
>>
>>
>> -adrian
>>
>> On 28 September 2016 at 23:46, Mori Hiroki <yamori813 at yahoo.co.jp> wrote:
>>>  Hi
>>>
>>>  Thanks for your advice. I can use USB on AR7161.
>>>
>>>  # gpioctl 2 1
>>>  # usbconfig
>>>
>>>  ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=0 md=HOST spd=FULL
>> (12Mbps) pwr=
>>>  SAVE (0mA)
>>>  ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=0 md=HOST spd=HIGH
>> (480Mbps) pwr
>>>  =SAVE (0mA)
>>>  ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, cfg=0 md=HOST
>> spd=FULL (
>>>  12Mbps) pwr=ON (100mA)
>>>
>>>  Thanks.
>>>
>>>  Hiroki Mori
>>>
>>>  ----- Original Message -----
>>>>  From: Adrian Chadd <adrian.chadd at gmail.com>
>>>>  To: Mori Hiroki <yamori813 at yahoo.co.jp>
>>>>  Cc: "freebsd-mips at freebsd.org"
>> <freebsd-mips at freebsd.org>
>>>>  Date: 2016/9/29, Thu 13:21
>>>>  Subject: Re: AR7161 USB
>>>>
>>>>  it could be something to do with port or phy power. check the default
>>>>  gpio settings for your board; some don't enable usb phy power.
>>>>
>>>>
>>>>  -a
>>>>
>>>>
>>>>  On 28 September 2016 at 20:51, Mori Hiroki
>> <yamori813 at yahoo.co.jp> wrote:
>>>>>   Hi.
>>>>>
>>>>>   on WZR-HP-G300NH(AR9132) OK
>>>>>
>>>>>
>>>>>
>>>>>   # usbconfig
>>>>>   ugen0.1: <EHCI root HUB Atheros> at usbus0, cfg=0 md=HOST
>> spd=HIGH
>>>>  (480Mbps) pwr
>>>>>   =SAVE (0mA)
>>>>>   ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0,
>> cfg=0 md=HOST
>>>>  spd=FULL (
>>>>>   12Mbps) pwr=ON (100mA)
>>>>>   #
>>>>>
>>>>>
>>>>>   on WZR-HP-AG300H(AR7161) NG
>>>>>
>>>>>   # usbconfig
>>>>>   ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=0 md=HOST
>> spd=FULL
>>>>  (12Mbps) pwr=
>>>>>   SAVE (0mA)
>>>>>   ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=0 md=HOST
>> spd=HIGH
>>>>  (480Mbps) pwr
>>>>>   =SAVE (0mA)
>>>>>
>>>>>   I use ZRouter on build. I check hints file. I seem same as
>>>>>   sys/mips/conf/AP96.hints.
>>>>>
>>>>>   Thanks
>>>>>
>>>>>   Hiroki Mori
>>>>>
>>>>>
>>>>>
>>>>>   ----- Original Message -----
>>>>>>   From: Sean Bruno <sbruno at freebsd.org>
>>>>>>   To: freebsd-mips at freebsd.org
>>>>>>   Cc:
>>>>>>   Date: 2016/9/27, Tue 23:10
>>>>>>   Subject: Re: AR7161 USB
>>>>>>
>>>>>>
>>>>>>
>>>>>>   On 09/27/16 04:02, Mori Hiroki wrote:
>>>>>>>    Hi.
>>>>>>>
>>>>>>>    I try to use AR7161 target(WZR-HP-AG300H) on head today.
>>>>>>>    But I can't use USB this target. Device is probe on
>> boot but
>>>>  USB device
>>>>>>>    insert not detect device.
>>>>>>>
>>>>>>>    Any one use this ?
>>>>>>>
>>>>>>>    Regards.
>>>>>>>
>>>>>>>    Hiroki Mori
>>>>>>
>>>>>>   Is umass.ko loaded? (I assume you are using a USB storage
>> device).
>>>>>>
>>>>>>   sean
>>>>>>
>>>>>   _______________________________________________
>>>>>   freebsd-mips at freebsd.org mailing list
>>>>>   https://lists.freebsd.org/mailman/listinfo/freebsd-mips
>>>>>   To unsubscribe, send any mail to
>>>>  "freebsd-mips-unsubscribe at freebsd.org"
>>>>
>>>  _______________________________________________
>>>  freebsd-mips at freebsd.org mailing list
>>>  https://lists.freebsd.org/mailman/listinfo/freebsd-mips
>>>  To unsubscribe, send any mail to
>> "freebsd-mips-unsubscribe at freebsd.org"
>>
> _______________________________________________
> freebsd-mips at freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-mips
> To unsubscribe, send any mail to "freebsd-mips-unsubscribe at freebsd.org"