Solve: AR7161 USB

[Mori Hiroki]

Hi.

I add this setting to rc script to WZR-HP-AG300H at ZRouter
build system.

I think sys/mips/conf have only soc base setting. Because of
soc and board setting is very scrambled. It is hard find target
setting. We are never correct all world board setting.

Regards

Hiroki Mori


----- Original Message -----
> From: Adrian Chadd <adrian.chadd at gmail.com>
> To: Mori Hiroki <yamori813 at yahoo.co.jp>
> Cc: "freebsd-mips at freebsd.org" <freebsd-mips at freebsd.org>
> Date: 2016/9/30, Fri 06:41
> Subject: Re: Solve: AR7161 USB
> 
> Cool. There's some stuff you can put in hints to set on/off gpio
> functions. Can you provide a diff to the right .hints file so it's
> done at boot time?
> 
> 
> -adrian
> 
> On 28 September 2016 at 23:46, Mori Hiroki <yamori813 at yahoo.co.jp> wrote:
>>  Hi
>> 
>>  Thanks for your advice. I can use USB on AR7161.
>> 
>>  # gpioctl 2 1
>>  # usbconfig
>> 
>>  ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=0 md=HOST spd=FULL 
> (12Mbps) pwr=
>>  SAVE (0mA)
>>  ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=0 md=HOST spd=HIGH 
> (480Mbps) pwr
>>  =SAVE (0mA)
>>  ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, cfg=0 md=HOST 
> spd=FULL (
>>  12Mbps) pwr=ON (100mA)
>> 
>>  Thanks.
>> 
>>  Hiroki Mori
>> 
>>  ----- Original Message -----
>>>  From: Adrian Chadd <adrian.chadd at gmail.com>
>>>  To: Mori Hiroki <yamori813 at yahoo.co.jp>
>>>  Cc: "freebsd-mips at freebsd.org" 
> <freebsd-mips at freebsd.org>
>>>  Date: 2016/9/29, Thu 13:21
>>>  Subject: Re: AR7161 USB
>>> 
>>>  it could be something to do with port or phy power. check the default
>>>  gpio settings for your board; some don't enable usb phy power.
>>> 
>>> 
>>>  -a
>>> 
>>> 
>>>  On 28 September 2016 at 20:51, Mori Hiroki 
> <yamori813 at yahoo.co.jp> wrote:
>>>>   Hi.
>>>> 
>>>>   on WZR-HP-G300NH(AR9132) OK
>>>> 
>>>> 
>>>> 
>>>>   # usbconfig
>>>>   ugen0.1: <EHCI root HUB Atheros> at usbus0, cfg=0 md=HOST 
> spd=HIGH
>>>  (480Mbps) pwr
>>>>   =SAVE (0mA)
>>>>   ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, 
> cfg=0 md=HOST
>>>  spd=FULL (
>>>>   12Mbps) pwr=ON (100mA)
>>>>   #
>>>> 
>>>> 
>>>>   on WZR-HP-AG300H(AR7161) NG
>>>> 
>>>>   # usbconfig
>>>>   ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=0 md=HOST 
> spd=FULL
>>>  (12Mbps) pwr=
>>>>   SAVE (0mA)
>>>>   ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=0 md=HOST 
> spd=HIGH
>>>  (480Mbps) pwr
>>>>   =SAVE (0mA)
>>>> 
>>>>   I use ZRouter on build. I check hints file. I seem same as
>>>>   sys/mips/conf/AP96.hints.
>>>> 
>>>>   Thanks
>>>> 
>>>>   Hiroki Mori
>>>> 
>>>> 
>>>> 
>>>>   ----- Original Message -----
>>>>>   From: Sean Bruno <sbruno at freebsd.org>
>>>>>   To: freebsd-mips at freebsd.org
>>>>>   Cc:
>>>>>   Date: 2016/9/27, Tue 23:10
>>>>>   Subject: Re: AR7161 USB
>>>>> 
>>>>> 
>>>>> 
>>>>>   On 09/27/16 04:02, Mori Hiroki wrote:
>>>>>>    Hi.
>>>>>> 
>>>>>>    I try to use AR7161 target(WZR-HP-AG300H) on head today.
>>>>>>    But I can't use USB this target. Device is probe on 
> boot but
>>>  USB device
>>>>>>    insert not detect device.
>>>>>> 
>>>>>>    Any one use this ?
>>>>>> 
>>>>>>    Regards.
>>>>>> 
>>>>>>    Hiroki Mori
>>>>> 
>>>>>   Is umass.ko loaded? (I assume you are using a USB storage 
> device).
>>>>> 
>>>>>   sean
>>>>> 
>>>>   _______________________________________________
>>>>   freebsd-mips at freebsd.org mailing list
>>>>   https://lists.freebsd.org/mailman/listinfo/freebsd-mips
>>>>   To unsubscribe, send any mail to
>>>  "freebsd-mips-unsubscribe at freebsd.org"
>>> 
>>  _______________________________________________
>>  freebsd-mips at freebsd.org mailing list
>>  https://lists.freebsd.org/mailman/listinfo/freebsd-mips
>>  To unsubscribe, send any mail to 
> "freebsd-mips-unsubscribe at freebsd.org"
>