Adaptec ATA RAID 1200A card supported?
Robert Ken Francis
rkfrancis1 at adelphia.net
Thu Sep 1 18:14:39 PDT 2005
Sorry to keep you in the dark about my hard drives. I have a 120GB drive master and a DVD reader as slave on ata0, ata1 is dead
(the BIOS won't detect anything), ata2 and ata3 are the Adaptec ATA RAID 1200A card (HighPoint chipset).
All of the FAILUREs went away when I disconnected the ata2 and ata3 drives from the card. See my dmesg below for details. I'm
guessing that SET FEATURES means I have set some features? I think the ata guy is at sos at FreeBSD.org?
Thanks,
Rob
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.4-RELEASE #0: Sun May 8 10:21:06 UTC 2005
root at harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
ACPI APIC Table: <ASUS P4SP-MX >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) CPU 2.40GHz (2400.18-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HT
T,TM,PBE>
real memory = 1040171008 (991 MB)
avail memory = 1008300032 (961 MB)
ioapic0 <Version 8.0> irqs 0-23 on motherboard
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <ASUS P4SP-MX> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 20
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <SiS 651 host to AGP bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <SiS 962 UDMA133 controller> port 0xa400-0xa40f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 16 at device 2.5 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
ohci0: <SiS 5571 USB controller> mem 0xe7000000-0xe7000fff irq 20 at device 3.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xe6800000-0xe6800fff irq 21 at device 3.1 on pci0
usb1: OHCI version 1.0, legacy support
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
pci0: <serial bus, USB> at device 3.3 (no driver attached)
sis0: <SiS 900 10/100BaseTX> port 0x8800-0x88ff mem 0xe5800000-0xe5800fff irq 19 at device 4.0 on pci0
miibus0: <MII bus> on sis0
rlphy0: <RTL8201L 10/100 media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0e:a6:98:41:8b
atapci1: <HighPoint HPT370 UDMA100 controller> port 0x7000-0x70ff,0x7400-0x7403,0x7800-0x7807,0x8000-0x8003,0x8400-0x8407 irq 17 at
device 14.0 on pci0
ata2: channel #0 on atapci1
ata3: channel #1 on atapci1
pci0: <multimedia, audio> at device 16.0 (no driver attached)
fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
orm0: <ISA Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 2400179128 Hz quality 800
Timecounters tick every 10.000 msec
ad0: 117246MB <Maxtor 6Y120L0/YAR41VW0> [238216/16/63] at ata0-master UDMA133
acd0: DVDROM <COMPAQ DVD-ROM GDR8160B/0012> at ata0-slave PIO4
Mounting root from ufs:/dev/ad0s1a
> -----Original Message-----
> From: Gary D. Margiotta [mailto:gary at tbe.net]
> Sent: Tuesday, August 30, 2005 8:41 PM
> To: Robert Ken Francis
> Cc: freebsd-hardware at freebsd.org
> Subject: RE: Adaptec ATA RAID 1200A card supported?
>
>
> Ok, I can see the explanation about the Highpoint chip.
>
> Based upon the actual error messages, I would examine the
> cables and speed
> settings first.
>
> My interpretation of the errors is that the card is having
> trouble finding
> a speed setting that will work with what I assume are ancient
> hard drives.
> The 42MB and 100MB drives I would guess are old, and don't
> speak DMA, or
> even a high PIO mode, and therefore are giving trouble when
> the card tries
> to set what the card thinks is a reasonable transfer speed setting.
>
> Out of curiosity, what happens if you were to unplug all the
> older drives
> from the card, and boot with only the newer hard drive
> attached and on
> (and maybe the CD drive, that should be fine as well)?
>
> If the errors go away I would then assume that it is a speed
> setting issue
> with the older drives, and then look further in that area.
> You might want
> to include Soren (the ata code maintainer) a little further
> down the line
> (if you search the -current mailing archives for ata, you'll find his
> e-mail address, I don't have it handy), if it does turn out to be a
> setting, which he may be better able to explain than I, being that he
> understands this stuff much better. Who knows, it may be
> something that
> needs a sysctl tunable, or maybe an alteration to the code,
> but some more
> troubleshooting should be done.
>
> Trying out the cables and that stuff first means you don't
> have to delve
> into a custom kernel at the moment, so try what's easiest
> first, and go
> from there.
>
> -Gary
>
> On Tue, 30 Aug 2005, Robert Ken Francis wrote:
>
> > Thanks for responding. I'm not sure what to do about this.
> Someone
> > in
> > FreeBSD questions said it was related to atapi or SCSI.
> The 1200A card
> > has a Highpoint HPT370 chip on it. I can see atapci1,
> ata2, and ata3.
> > Maybe the hard drives cause these driver failures?
> >
> > I can try to take out atapifd and see if the errors go away, which
> > means
> > I will have to build a kernel. Does anyone know what
> causes the below
> > FAILUREs?
> >
> > Thanks,
> > Rob
> >
> >> -----Original Message-----
> >> From: owner-freebsd-hardware at freebsd.org
> >> [mailto:owner-freebsd-hardware at freebsd.org] On Behalf Of Gary D.
> >> Margiotta
> >> Sent: Sunday, August 28, 2005 11:13 AM
> >> To: Robert Ken Francis
> >> Cc: freebsd-hardware at freebsd.org
> >> Subject: Re: Adaptec ATA RAID 1200A card supported?
> >>
> >>
> >> The card itself is supported fine, the box I'm composing this mail
> >> from is using solely an Adaptec 1200A card, running 5-STABLE (which
> >> was originally
> >> installed with 5.2.1, and have been tracking -STABLE since).
> >>
> >> I don't see the Adaptec card getting probed in your dmesg... I see
> >> the onboard SiS controller (atapci0 with ata0 and ata1), and a
> >> HighPoint card
> >> (atapci1 with ata-2 and ata-3), and the errors I see are
> >> coming from the
> >> ata-2 and ata-3 channels, which are on the HighPoint controller.
> >>
> >> -Gary
> >>
> >> On Sun, 28 Aug 2005, Robert Ken Francis wrote:
> >>
> >>> I have failures like the below:
> >>>
> >>> ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE
> >>> status=51<READY,DSC,ERROR> error=4<ABORTED>
> >>>
> >>> What do I do to fix these failures? All of the "FAILURE"
> >> drives are
> >>> on my Adaptec ATA RAID 1200A card. My secondary built-in
> >> IDE is dead
> >>> so I have to use this card as an IDE replacement.
> >>>
> >>> Thanks,
> >>> Rob
> >>>
> >>> Note that NetBSD doesn't have this problem.
> >>>
> >>>
> >>> Here is my dmesg:
> >>>
> >>> Copyright (c) 1992-2005 The FreeBSD Project.
> >>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991,
> >> 1992, 1993, 1994
> >>> The Regents of the University of California. All rights
> >> reserved. FreeBSD 5.4-RELEASE #0: Sun May 8 10:21:06 UTC 2005
> >>> root at harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
> >>> ACPI APIC Table: <ASUS P4SP-MX >
> >>> Timecounter "i8254" frequency 1193182 Hz quality 0
> >>> CPU: Intel(R) Celeron(R) CPU 2.40GHz (2400.18-MHz 686-class CPU)
> >>> Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
> >>>
> >>>
> >>
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,
> >> P
> >>> GE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HT
> >>> T,TM,PBE>
> >>> real memory = 1040171008 (991 MB)
> >>> avail memory = 1008295936 (961 MB)
> >>> ioapic0 <Version 8.0> irqs 0-23 on motherboard
> >>> npx0: <math processor> on motherboard
> >>> npx0: INT 16 interface
> >>> acpi0: <ASUS P4SP-MX> on motherboard
> >>> acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 20
> >>> acpi0: Power Button (fixed)
> >>> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> >>> acpi_timer0: <24-bit timer at 3.579545MHz> port
> >> 0xe408-0xe40b on acpi0
> >>> cpu0: <ACPI CPU> on acpi0
> >>> acpi_throttle0: <ACPI CPU Throttling> on cpu0
> >>> acpi_button0: <Power Button> on acpi0
> >>> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> >>> pci0: <ACPI PCI bus> on pcib0
> >>> agp0: <SiS 651 host to AGP bridge> mem
> >> 0xe8000000-0xebffffff at device 0.0 on pci0
> >>> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> >>> pci1: <ACPI PCI bus> on pcib1
> >>> pci1: <display, VGA> at device 0.0 (no driver attached)
> >>> isab0: <PCI-ISA bridge> at device 2.0 on pci0
> >>> isa0: <ISA bus> on isab0
> >>> atapci0: <SiS 962 UDMA133 controller> port
> >> 0xa400-0xa40f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 16 at device
> >> 2.5 on pci0
> >>> ata0: channel #0 on atapci0
> >>> ata1: channel #1 on atapci0
> >>> ohci0: <SiS 5571 USB controller> mem 0xe7000000-0xe7000fff
> >> irq 20 at device 3.0 on pci0
> >>> usb0: OHCI version 1.0, legacy support
> >>> usb0: <SiS 5571 USB controller> on ohci0
> >>> usb0: USB revision 1.0
> >>> uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> >>> uhub0: 3 ports with 3 removable, self powered
> >>> ohci1: <SiS 5571 USB controller> mem 0xe6800000-0xe6800fff
> >> irq 21 at device 3.1 on pci0
> >>> usb1: OHCI version 1.0, legacy support
> >>> usb1: <SiS 5571 USB controller> on ohci1
> >>> usb1: USB revision 1.0
> >>> uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> >>> uhub1: 3 ports with 3 removable, self powered
> >>> pci0: <serial bus, USB> at device 3.3 (no driver attached)
> >>> sis0: <SiS 900 10/100BaseTX> port 0x8800-0x88ff mem
> >> 0xe5800000-0xe5800fff irq 19 at device 4.0 on pci0
> >>> miibus0: <MII bus> on sis0
> >>> rlphy0: <RTL8201L 10/100 media interface> on miibus0
> >>> rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> >>> sis0: Ethernet address: 00:0e:a6:98:41:8b
> >>> atapci1: <HighPoint HPT370 UDMA100 controller> port
> >> 0x7000-0x70ff,0x7400-0x7403,0x7800-0x7807,0x8000-0x8003,0x8400
> >> -0x8407 irq 17 at
> >>> device 14.0 on pci0
> >>> ata2: channel #0 on atapci1
> >>> ata3: channel #1 on atapci1
> >>> pci0: <multimedia, audio> at device 16.0 (no driver attached)
> >>> fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq
> >> 6 drq 2 on acpi0
> >>> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> >>> ppc0: <ECP parallel printer port> port
> >> 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
> >>> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> >>> ppc0: FIFO with 16/16/16 bytes threshold
> >>> ppbus0: <Parallel port bus> on ppc0
> >>> plip0: <PLIP network interface> on ppbus0
> >>> lpt0: <Printer> on ppbus0
> >>> lpt0: Interrupt-driven port
> >>> ppi0: <Parallel I/O> on ppbus0
> >>> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4
> >> flags 0x10 on acpi0
> >>> sio0: type 16550A
> >>> atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq
> 1 on acpi0
> >>> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> >>> kbd0 at atkbd0
> >>> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> >>> psm0: model IntelliMouse, device ID 3
> >>> orm0: <ISA Option ROMs> at iomem
> >> 0xcc000-0xd07ff,0xc0000-0xcbfff on isa0 pmtimer0 on isa0
> >>> sc0: <System console> at flags 0x100 on isa0
> >>> sc0: VGA <16 virtual consoles, flags=0x300>
> >>> sio1: configured irq 3 not in bitmap of probed irqs 0
> >>> sio1: port may not be enabled
> >>> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
> >> 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 2400181916 Hz
> >> quality 800
> >>> Timecounters tick every 10.000 msec
> >>> ad0: 117246MB <Maxtor 6Y120L0/YAR41VW0> [238216/16/63] at
> >> ata0-master UDMA133
> >>> acd0: DVDROM <COMPAQ DVD-ROM GDR8160B/0012> at ata0-slave PIO4
> >>> ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE
> >> status=51<READY,DSC,ERROR> error=4<ABORTED>
> >>> ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE
> >> status=51<READY,DSC,ERROR> error=4<ABORTED>
> >>> ata2-slave: FAILURE - SETFEATURES SET TRANSFER MODE
> >> status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH>
> >>> ata2-slave: FAILURE - SETFEATURES SET TRANSFER MODE
> >> status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH>
> >>> ad4: FAILURE - SETFEATURES ENABLE RCACHE
> >> status=51<READY,DSC,ERROR> error=4<ABORTED>
> >>> ad4: FAILURE - SETFEATURES ENABLE WCACHE
> >> status=51<READY,DSC,ERROR> error=4<ABORTED>
> >>> ad4: 40MB <MiniScribe Corporation 8051A/3.73> [745/4/28] at
> >> ata2-master PIO0
> >>> ad5: FAILURE - SETFEATURES ENABLE WCACHE
> >> status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH>
> >>> ad5: 41MB <Conner Peripherals 40MB - CP3041/S2.46>
> >> [1053/2/40] at ata2-slave PIO0
> >>> ata3-master: FAILURE - SETFEATURES SET TRANSFER MODE
> >> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> >>> ata3-master: FAILURE - SETFEATURES SET TRANSFER MODE
> >> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> >>> ata3-slave: FAILURE - SETFEATURES SET TRANSFER MODE
> >> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> >>> ata3-slave: FAILURE - SETFEATURES SET TRANSFER MODE
> >> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> >>> ad6: FAILURE - SETFEATURES ENABLE WCACHE
> >> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> >>> ad6: 102MB <st3120AT/REV184.0> [1024/12/17] at ata3-master PIO0
> >>> ad7: FAILURE - SETFEATURES ENABLE WCACHE
> >> status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND>
> >>> ad7: 102MB <st3120AT/REV184.0> [1024/12/17] at ata3-slave PIO0
> >>> ad4: FAILURE - READ status=51<READY,DSC,ERROR>
> >> error=10<NID_NOT_FOUND> LBA=18 Mounting root from ufs:/dev/ad0s1a
> >>>
> >>> --
> >>> No virus found in this outgoing message.
> >>> Checked by AVG Anti-Virus.
> >>> Version: 7.0.344 / Virus Database: 267.10.16/83 - Release
> >> Date: 8/26/2005
> >>>
> >>>
> >>> _______________________________________________
> >>> freebsd-hardware at freebsd.org mailing list
> >>> http://lists.freebsd.org/mailman/listinfo/freebsd-hardware
> >>> To unsubscribe, send any mail to
> >>> "freebsd-hardware-unsubscribe at freebsd.org"
> >>>
> >> _______________________________________________
> >> freebsd-hardware at freebsd.org mailing list
> >> http://lists.freebsd.org/mailman/listinfo/freebsd-hardware
> >> To unsubscribe, send any mail to
> >> "freebsd-hardware-unsubscribe at freebsd.org"
> >>
> >> --
> >> No virus found in this incoming message.
> >> Checked by AVG Anti-Virus.
> >> Version: 7.0.344 / Virus Database: 267.10.16/83 - Release
> >> Date: 8/26/2005
> >>
> >>
> >
> > --
> > No virus found in this outgoing message.
> > Checked by AVG Anti-Virus.
> > Version: 7.0.344 / Virus Database: 267.10.17/84 - Release
> Date: 8/29/2005
> >
> >
> > _______________________________________________
> > freebsd-hardware at freebsd.org mailing list
> > http://lists.freebsd.org/mailman/listinfo/freebsd-hardware
> > To unsubscribe, send any mail to
> > "freebsd-hardware-unsubscribe at freebsd.org"
> >
>
> --
> No virus found in this incoming message.
> Checked by AVG Anti-Virus.
> Version: 7.0.344 / Virus Database: 267.10.17/84 - Release
> Date: 8/29/2005
>
>
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.344 / Virus Database: 267.10.18/88 - Release Date: 9/1/2005
More information about the freebsd-hardware
mailing list