Any successful installs on a Broadcom HT1000 chipset?

Travis Mikalson bofh at terranova.net
Thu Nov 29 08:34:52 PST 2007


Andrey V. Elsukov wrote:
> Søren Schmidt wrote:
>>> Anton Yuzhaninov has mentioned in the top of this thread that
>>> this bug may be easy reproduced by using external PCI-X card.
>>> He tried use PCI-X Marvell card and got lots of corruptions on
>>> the integrated HT1000. Can you or Soren try the same way to
>>> reproduce?
>> As I told earlier the fileserver I have here with the HT1000 chip also 
>> has a marvel 6081 and it is on PCI-X. There are 4 disks on each and it 
>> moves lots of data around on a daily basis, no problems whatsoever. I 
>> have planned downtime today on it and will experiment with it, but I 
>> can't hold it off for too long...
> 
> May be here is different HW revisions? You have an old revision and now 
> people with this bug have a new revision?
> I don't see in the this thread any verbose dmesg or pciconf outputs.
> So, people, who have problems and who don't have it, can you show
> your `pciconf -l`?

I think I posted it already but here it is again. I should also mention 
I just updated my BIOS to a very recently released one from Tyan (v2.00) 
and it had no effect and I've also tweaked pretty much every weird 
obscure knob in the CMOS to no avail... Including disabling serial and 
on-board NICs and using the SATA controller in P-ATA (legacy) mode, etc.

This is the board that works poorly as I described yesterday with 6.2, 
6.3 and has the memory/data corruption in RELENG_7.

$ pciconf -lv
pcib1 at pci0:0:1:0:       class=0x060400 card=0x00000000 chip=0x00361166 
rev=0x00 hdr=0x01
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = 'HT1000 PCI/PCI-X bridge'
     class      = bridge
     subclass   = PCI-PCI
hostb0 at pci0:0:2:0:      class=0x060000 card=0x02011166 chip=0x02051166 
rev=0x00 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = 'HT1000 Legacy South Bridge'
     class      = bridge
     subclass   = HOST-PCI
atapci1 at pci0:0:2:1:     class=0x01018a card=0x02141166 chip=0x02141166 
rev=0x00 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = 'HT1000 Legacy IDE controller'
     class      = mass storage
     subclass   = ATA
isab0 at pci0:0:2:2:       class=0x060100 card=0x02301166 chip=0x02341166 
rev=0x00 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = 'HT1000 LPC Bridge'
     class      = bridge
     subclass   = PCI-ISA
none0 at pci0:0:3:0:       class=0x0c0310 card=0x02231166 chip=0x02231166 
rev=0x01 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = '0x0223 USB controller'
     class      = serial bus
     subclass   = USB
none1 at pci0:0:3:1:       class=0x0c0310 card=0x02231166 chip=0x02231166 
rev=0x01 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = '0x0223 USB controller'
     class      = serial bus
     subclass   = USB
none2 at pci0:0:3:2:       class=0x0c0320 card=0x02231166 chip=0x02231166 
rev=0x01 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = '0x0223 USB controller'
     class      = serial bus
     subclass   = USB
em0 at pci0:0:4:0: class=0x020000 card=0x387010f1 chip=0x10768086 rev=0x05 
hdr=0x00
     vendor     = 'Intel Corporation'
     device     = '82541EI Gigabit Ethernet Controller'
     class      = network
     subclass   = ethernet
em1 at pci0:0:5:0: class=0x020000 card=0x387010f1 chip=0x10768086 rev=0x05 
hdr=0x00
     vendor     = 'Intel Corporation'
     device     = '82541EI Gigabit Ethernet Controller'
     class      = network
     subclass   = ethernet
vgapci0 at pci0:0:6:0:     class=0x030000 card=0x002018ca chip=0x002018ca 
rev=0x00 hdr=0x00
     vendor     = 'XGI Technology Inc'
     class      = display
     subclass   = VGA
atapci2 at pci0:0:7:0:     class=0x010400 card=0x61141095 chip=0x31141095 
rev=0x02 hdr=0x00
     vendor     = 'Silicon Image Inc (Was: CMD Technology Inc)'
     device     = 'Sil 3114 SATALink/SATARaid Controller'
     class      = mass storage
     subclass   = RAID
hostb1 at pci0:0:24:0:     class=0x060000 card=0x00000000 chip=0x11001022 
rev=0x00 hdr=0x00
     vendor     = 'Advanced Micro Devices (AMD)'
     device     = '(K8) Athlon 64/Opteron HyperTransport Technology 
Configuration'
     class      = bridge
     subclass   = HOST-PCI
hostb2 at pci0:0:24:1:     class=0x060000 card=0x00000000 chip=0x11011022 
rev=0x00 hdr=0x00
     vendor     = 'Advanced Micro Devices (AMD)'
     device     = '(K8) Athlon 64/Opteron Address Map'
     class      = bridge
     subclass   = HOST-PCI
hostb3 at pci0:0:24:2:     class=0x060000 card=0x00000000 chip=0x11021022 
rev=0x00 hdr=0x00
     vendor     = 'Advanced Micro Devices (AMD)'
     device     = '(K8) Athlon 64/Opteron DRAM Controller'
     class      = bridge
     subclass   = HOST-PCI
hostb4 at pci0:0:24:3:     class=0x060000 card=0x00000000 chip=0x11031022 
rev=0x00 hdr=0x00
     vendor     = 'Advanced Micro Devices (AMD)'
     device     = '(K8) Athlon 64/Opteron Miscellaneous Control'
     class      = bridge
     subclass   = HOST-PCI
pcib2 at pci0:1:13:0:      class=0x060400 card=0x4f00d3f7 chip=0x01041166 
rev=0xc0 hdr=0x01
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = 'HT1000 PCI/PCI-X bridge'
     class      = bridge
     subclass   = PCI-PCI
atapci0 at pci0:1:14:0:    class=0x010405 card=0x024a1166 chip=0x024a1166 
rev=0x00 hdr=0x00
     vendor     = 'ServerWorks (Was: Reliance Computer Corp)'
     device     = 'BCM5785 (HT1000) SATA Native SATA Mode'
     class      = mass storage
     subclass   = RAID

$ cat /var/run/dmesg.boot
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-BETA3 #8: Tue Nov 27 16:59:39 UTC 2007
     tog at newtog.tog.net:/usr/obj/usr/src/sys/tognet
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Dual-Core AMD Opteron(tm) Processor 1212 (1995.02-MHz K8-class CPU)
   Origin = "AuthenticAMD"  Id = 0x40f32  Stepping = 2
 
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
   Features2=0x2001<SSE3,CX16>
   AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
   AMD Features2=0x1f<LAHF,CMP,SVM,ExtAPIC,CR8>
   Cores per package: 2
usable memory = 2138079232 (2039 MB)
avail memory  = 2062680064 (1967 MB)
ACPI APIC Table: <A M I  OEMAPIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
  cpu0 (BSP): APIC ID:  0
  cpu1 (AP): APIC ID:  1
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
ioapic2 <Version 1.1> irqs 32-47 on motherboard
kbd1 at kbdmux0
acpi0: <A M I OEMXSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 7ff00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
cpu0: <ACPI CPU> on acpi0
powernow0: <PowerNow! K8> on cpu0
device_attach: powernow0 attach returned 6
cpu1: <ACPI CPU> on acpi0
powernow1: <PowerNow! K8> on cpu1
device_attach: powernow1 attach returned 6
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 13.0 on pci1
pci2: <ACPI PCI bus> on pcib2
atapci0: <ServerWorks HT1000 SATA150 controller> port 
0xc080-0xc087,0xc000-0xc003,0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb81f 
mem 0xff2fe000-0xff2fffff irq 11 at device 14.0 on pci1
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: [ITHREAD]
atapci1: <ServerWorks HT1000 UDMA100 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 2.1 on pci0
ata0: <ATA channel 0> on atapci1
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci1
ata1: [ITHREAD]
isab0: <PCI-ISA bridge> at device 2.2 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, USB> at device 3.0 (no driver attached)
pci0: <serial bus, USB> at device 3.1 (no driver attached)
pci0: <serial bus, USB> at device 3.2 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection Version - 6.5.3> port 
0xe000-0xe03f mem 0xff680000-0xff69ffff,0xff5e0000-0xff5fffff irq 24 at 
device 4.0 on pci0
em0: Ethernet address: 00:e0:81:81:25:0a
em0: [FILTER]
em1: <Intel(R) PRO/1000 Network Connection Version - 6.5.3> port 
0xdc00-0xdc3f mem 0xff5a0000-0xff5bffff,0xff580000-0xff59ffff irq 25 at 
device 5.0 on pci0
em1: Ethernet address: 00:e0:81:81:25:0b
em1: [FILTER]
vgapci0: <VGA-compatible display> port 0xec00-0xec7f mem 
0xf8000000-0xfbffffff,0xff6c0000-0xff6fffff at device 6.0 on pci0
atapci2: <SiI SiI 3114 SATA150 controller> port 
0xe880-0xe887,0xe800-0xe803,0xe480-0xe487,0xe400-0xe403,0xe080-0xe08f 
mem 0xff6bbc00-0xff6bbfff irq 27 at device 7.0 on pci0
atapci2: [ITHREAD]
ata6: <ATA channel 0> on atapci2
ata6: [ITHREAD]
ata7: <ATA channel 1> on atapci2
ata7: [ITHREAD]
ata8: <ATA channel 2> on atapci2
ata8: [ITHREAD]
ata9: <ATA channel 3> on atapci2
ata9: [ITHREAD]
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on 
acpi0
sio0: type 16550A
sio0: [FILTER]
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcc7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
WARNING: ZFS is considered to be an experimental feature in FreeBSD.
Timecounters tick every 1.000 msec
ZFS filesystem version 6
ZFS storage pool version 6
acd0: DVDROM <Pioneer DVD-ROM ATAPIModel DVD-106S 0109/E1.09> at 
ata0-master UDMA66
ad12: 476940MB <Seagate ST3500630NS 3.AEG> at ata6-master SATA150
ad14: 476940MB <Seagate ST3500630NS 3.AEG> at ata7-master SATA150
SMP: AP CPU #1 Launched!
GEOM_MIRROR: Device mirror/gm0 launched (2/2).
GEOM_MIRROR: Device mirror/gm1 launched (2/2).
WARNING: Expected rawoffset 0, found 63
Trying to mount root from zfs:zroot
WARNING: Expected rawoffset 0, found 63



-- 
TerraNovaNet Internet Services - Key Largo, FL
Voice: (305)453-4011 x101   Fax: (305)451-5991
http://www.terranova.net/
----------------------------------------------
Life's not fair, but the root password helps.


More information about the freebsd-current mailing list