two problems with broadcom NICs

Alessandro de Manzano ale at unixmania.net
Fri Mar 2 10:22:42 UTC 2007


Hello,

I've got a bunch of new Dell PowerEdge SC440 machines, but I've some
problems running FreeBSD on them.

OS: FreeBSD 6.2-RELEASE (but also -stable of yesterday), SMP (but tried
also GENERIC monoprocessor), both i386 and amd64, always same results.

Situation: Two Broadcom NICs, one on the motherboard and one on
PCI-express bus, here is a snippet of pciconf -lv (as you can see I had
to add a 3COM PCI card in order to have connectivity)


bge0 at pci3:0:0:	class=0x020000 card=0x165914e4 chip=0x165914e4 rev=0x21 hdr=0x00
    vendor     = 'Broadcom Corporation'
    device     = 'BCM5750A1 NetXtreme Gigabit Ethernet PCI Express'
    class      = network
    subclass   = ethernet
none1 at pci4:0:0:	class=0x020000 card=0x01df1028 chip=0x167a14e4 rev=0x02 hdr=0x00
    vendor     = 'Broadcom Corporation'
    class      = network
    subclass   = ethernet
xl0 at pci5:2:0:	class=0x020000 card=0x100010b7 chip=0x920010b7 rev=0x74 hdr=0x00
    vendor     = '3COM Corp, Networking Division'
    device     = '3C905C-TX Fast EtherLink for PC Management NIC'
    class      = network
    subclass   = ethernet

The first one (bge0) is the motherboard integrated, the second one
(none1) is on PCI-express


Problems:

First NIC: recognized, but it never see the carrier.
ifconfig gives always this result:

bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
	options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
	ether 00:10:18:27:f3:4c
	media: Ethernet autoselect (none)
	status: no carrier

No matter of what I do (change cable, change remote switch) it always
gives "status: no carrier".
Leds on the RJ-45 female connector are on (orange one for link) and off
(activity). On the switch(es) link leds are always correctly on, so
physic carrier should be present.

What could be ? What could I try ? Ideas ?


Second NIC: is not recognized at all. Maybe it's a matter of missing
PCI IDs ? I don't know exactly which model is supposed to be, searching
for those IDs gives inconsitances results..


This is a not-yet-in-production machine, so I can do any experiment
necessary to solve these problems

Hoping in your help ;)

below is my full verbose dmesg

Many thanks anyway!


-- 

bye!

Ale


Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE #0: Thu Mar  1 12:21:39 CET 2007
    root at power64.playstos.ldr:/usr/obj/usr/src/sys/POWER64
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80a9b000.
Preloaded elf obj module "/boot/kernel/geom_mirror.ko" at 0xffffffff80a9b1f8.
INTR: Adding local APIC 0 as a target
ACPI APIC Table: <DELL   B8K    >
Calibrating clock(s) ... i8254 clock: 1193207 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1862010668 Hz
CPU: Intel(R) Xeon(R) CPU            3040  @ 1.86GHz (1862.01-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x6f6  Stepping = 6
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,XTPR,<b15>>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  Cores per package: 2
real memory  = 1072152576 (1022 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x0000000000b98000 - 0x000000003e03efff, 1028288512 bytes (251047 pages)
avail memory = 1022246912 (974 MB)
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 8
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
lapic: Routing NMI -> LINT1
lapic: LINT1 trigger: level
lapic: LINT1 polarity: high
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic0: Forcing LINT1 to edge trigger
cpu0 BSP:
     ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00008400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
io: <I/O>
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
rr232x: RocketRAID 232x controller driver v1.02 (Mar  1 2007 12:21:26)
acpi0: <DELL B8K    > on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80000098
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=27788086)
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 6 7 9 10 11 12 15
  Validation          0   11   N     0  3 4 5 6 7 9 10 11 12 15
  After Disable       0  255   N     0  3 4 5 6 7 9 10 11 12 15
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 5 6 7 9 10 11 12 15
  Validation          0   10   N     0  3 4 5 6 7 9 10 11 12 15
  After Disable       0  255   N     0  3 4 5 6 7 9 10 11 12 15
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    3   N     0  3 4 5 6 7 9 10 11 12 15
  Validation          0    3   N     0  3 4 5 6 7 9 10 11 12 15
  After Disable       0  255   N     0  3 4 5 6 7 9 10 11 12 15
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    9   N     0  3 4 5 6 7 9 10 11 12 15
  Validation          0    9   N     0  3 4 5 6 7 9 10 11 12 15
  After Disable       0  255   N     0  3 4 5 6 7 9 10 11 12 15
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    5   N     0  3 4 5 6 7 9 10 11 12 15
  Validation          0    5   N     0  3 4 5 6 7 9 10 11 12 15
  After Disable       0  255   N     0  3 4 5 6 7 9 10 11 12 15
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    9   N     0  3 4 5 6 7 9 10 11 12 15
  Validation          0    9   N     0  3 4 5 6 7 9 10 11 12 15
  After Disable       0  255   N     0  3 4 5 6 7 9 10 11 12 15
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    5   N     0  3 4 5 6 7 9 10 11 12 15
  Validation          0    5   N     0  3 4 5 6 7 9 10 11 12 15
  After Disable       0  255   N     0  3 4 5 6 7 9 10 11 12 15
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 5 6 7 9 10 11 12 15
  Validation          0   10   N     0  3 4 5 6 7 9 10 11 12 15
  After Disable       0  255   N     0  3 4 5 6 7 9 10 11 12 15
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found->	vendor=0x8086, dev=0x2778, revid=0x00
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x2779, revid=0x00
	bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
found->	vendor=0x8086, dev=0x27d0, revid=0x01
	bus=0, slot=28, func=0
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found->	vendor=0x8086, dev=0x27e0, revid=0x01
	bus=0, slot=28, func=4
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found->	vendor=0x8086, dev=0x27e2, revid=0x01
	bus=0, slot=28, func=5
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	powerspec 2  supports D0 D3  current D0
	MSI supports 1 message
pcib0: matched entry for 0.28.INTB
pcib0: slot 28 INTB hardwired to IRQ 17
found->	vendor=0x8086, dev=0x27c8, revid=0x01
	bus=0, slot=29, func=0
	class=0c-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=9
	map[20]: type 4, range 32, base 0000ff80, size  5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 21
found->	vendor=0x8086, dev=0x27c9, revid=0x01
	bus=0, slot=29, func=1
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=5
	map[20]: type 4, range 32, base 0000ff60, size  5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 22
found->	vendor=0x8086, dev=0x27ca, revid=0x01
	bus=0, slot=29, func=2
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=3
	map[20]: type 4, range 32, base 0000ff40, size  5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 18
found->	vendor=0x8086, dev=0x27cb, revid=0x01
	bus=0, slot=29, func=3
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=10
	map[20]: type 4, range 32, base 0000ff20, size  5, enabled
pcib0: matched entry for 0.29.INTD
pcib0: slot 29 INTD hardwired to IRQ 23
found->	vendor=0x8086, dev=0x27cc, revid=0x01
	bus=0, slot=29, func=7
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=9
	powerspec 2  supports D0 D3  current D0
	map[10]: type 1, range 32, base ff980800, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 21
found->	vendor=0x8086, dev=0x244e, revid=0xe1
	bus=0, slot=30, func=0
	class=06-04-01, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x27b8, revid=0x01
	bus=0, slot=31, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0107, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x27df, revid=0x01
	bus=0, slot=31, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0288, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	map[20]: type 4, range 32, base 0000ffa0, size  4, enabled
pcib0: matched entry for 0.31.INTA
pcib0: slot 31 INTA hardwired to IRQ 16
found->	vendor=0x8086, dev=0x27c0, revid=0x01
	bus=0, slot=31, func=2
	class=01-01-8f, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=5
	powerspec 2  supports D0 D3  current D0
	map[10]: type 4, range 32, base 0000fe00, size  3, enabled
	map[14]: type 4, range 32, base 0000fe10, size  2, enabled
	map[18]: type 4, range 32, base 0000fe20, size  3, enabled
	map[1c]: type 4, range 32, base 0000fe30, size  2, enabled
	map[20]: type 4, range 32, base 0000fec0, size  4, enabled
	map[24]: type 1, range 32, base effffc00, size 10, enabled
pcib0: matched entry for 0.31.INTC
pcib0: slot 31 INTC hardwired to IRQ 20
found->	vendor=0x8086, dev=0x27da, revid=0x01
	bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0101, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	map[20]: type 4, range 32, base 0000ece0, size  5, enabled
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 17
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xf000-0xfff
pcib1:   memory decode     0xefe00000-0xefefffff
pcib1:   prefetched decode 0xfff00000-0xfffff
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0xf000-0xfff
pcib2:   memory decode     0xefd00000-0xefdfffff
pcib2:   prefetched decode 0xfff00000-0xfffff
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pcib3:   secondary bus     3
pcib3:   subordinate bus   3
pcib3:   I/O decode        0xf000-0xfff
pcib3:   memory decode     0xefc00000-0xefcfffff
pcib3:   prefetched decode 0xfff00000-0xfffff
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
found->	vendor=0x14e4, dev=0x1659, revid=0x21
	bus=3, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	MSI supports 8 messages, 64 bit
	map[10]: type 1, range 64, base efcf0000, size 16, enabled
pcib3: requested memory range 0xefcf0000-0xefcfffff: good
pcib3: matched entry for 3.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 16
bge0: <Broadcom BCM5750 C1, ASIC rev. 0x4201> mem 0xefcf0000-0xefcfffff irq 16 at device 0.0 on pci3
bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xefcf0000
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: bpf attached
bge0: Ethernet address: 00:10:18:27:f3:4c
ioapic0: routing intpin 16 (PCI IRQ 16) to vector 49
bge0: [MPSAFE]
pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pcib4:   I/O decode        0xf000-0xfff
pcib4:   memory decode     0xefb00000-0xefbfffff
pcib4:   prefetched decode 0xfff00000-0xfffff
pci4: <ACPI PCI bus> on pcib4
pci4: physical bus=4
found->	vendor=0x14e4, dev=0x167a, revid=0x02
	bus=4, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type 1, range 64, base efbf0000, size 16, enabled
pcib4: requested memory range 0xefbf0000-0xefbfffff: good
pcib4: matched entry for 4.0.INTA
pcib4: slot 0 INTA hardwired to IRQ 17
pci4: <network, ethernet> at device 0.0 (no driver attached)
uhci0: <UHCI (generic) USB controller> port 0xff80-0xff9f irq 21 at device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff80
ioapic0: routing intpin 21 (PCI IRQ 21) to vector 50
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xff60-0xff7f irq 22 at device 29.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff60
ioapic0: routing intpin 22 (PCI IRQ 22) to vector 51
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff40
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 52
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0xff20-0xff3f irq 23 at device 29.3 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff20
ioapic0: routing intpin 23 (PCI IRQ 23) to vector 53
uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xff980800-0xff980bff irq 21 at device 29.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xff980800
ehci0: [GIANT-LOCKED]
usb4: waiting for BIOS to give up control
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib5:   secondary bus     5
pcib5:   subordinate bus   5
pcib5:   I/O decode        0xd000-0xdfff
pcib5:   memory decode     0xef900000-0xefafffff
pcib5:   prefetched decode 0xe0000000-0xe7ffffff
pcib5:   Subtractively decoded bridge.
pci5: <ACPI PCI bus> on pcib5
pci5: physical bus=5
found->	vendor=0x10b7, dev=0x9200, revid=0x74
	bus=5, slot=2, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x0210, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
	intpin=a, irq=3
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 4, range 32, base 0000d880, size  7, enabled
pcib5: requested I/O range 0xd880-0xd8ff: in range
	map[14]: type 1, range 32, base ef9eff80, size  7, enabled
pcib5: requested memory range 0xef9eff80-0xef9effff: good
pcib5: matched entry for 5.2.INTA
pcib5: slot 2 INTA hardwired to IRQ 18
found->	vendor=0x1002, dev=0x515e, revid=0x02
	bus=5, slot=7, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0183, statreg=0x0290, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=9
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 3, range 32, base e0000000, size 27, enabled
pcib5: requested memory range 0xe0000000-0xe7ffffff: good
	map[14]: type 4, range 32, base 0000dc00, size  8, enabled
pcib5: requested I/O range 0xdc00-0xdcff: in range
	map[18]: type 1, range 32, base ef9f0000, size 16, enabled
pcib5: requested memory range 0xef9f0000-0xef9fffff: good
pcib5: matched entry for 5.7.INTA
pcib5: slot 7 INTA hardwired to IRQ 19
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xd880-0xd8ff mem 0xef9eff80-0xef9effff irq 18 at device 2.0 on pci5
xl0: Reserved 0x80 bytes for rid 0x14 type 3 at 0xef9eff80
xl0: using memory mapped I/O
xl0: media options word: a
xl0: found MII/AUTO
miibus1: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus1
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:04:76:24:2c:e6
xl0: [MPSAFE]
pci5: <display, VGA> at device 7.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf irq 16 at device 31.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=01
ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0: stat1=0x01 err=0x04 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=00 stat1=01 devices=0x4<ATAPI_MASTER>
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 54
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 55
ata1: [MPSAFE]
atapci1: <Intel ICH7 SATA300 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfecf mem 0xeffffc00-0xefffffff irq 20 at device 31.2 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfec0
ioapic0: routing intpin 20 (PCI IRQ 20) to vector 56
atapci1: [MPSAFE]
ata2: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0xfe00
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xfe10
ata2: reset tp1 mask=03 ostat0=80 ostat1=80
ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: stat1=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xfe20
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xfe30
ata3: reset tp1 mask=00 ostat0=ff ostat1=ff
ata3: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to vector 57
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x4c29 0x4c39 0x4c29 0x4c29
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 58
ahc_isa_probe 0: ioport 0xc00 alloc failed
ahc_isa_probe 13: ioport 0xdc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
ex_isa_identify()
fdc: fdc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xc97ff,0xc9800-0xcb7ff,0xcb800-0xcbfff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0045
atkbd: keyboard ID 0xffffffff (1)
atkbd: failed to reset the keyboard.
kbd0 at atkbd0
kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 59
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0045
psm0: failed to reset the aux device.
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x4c29 0x4c29 0x4c29 0x4c29
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
isa_probe_children: probing PnP devices
ums0: Dell Dell USB Mouse, rev 1.10/29.10, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhub5: vendor 0x0451 product 0x1446, class 9/0, rev 1.10/1.10, addr 2
uhub5: 4 ports with 4 removable, self powered
ukbd0: vendor 0x045e Microsoft Internet Keyboard Pro, rev 1.10/1.11, addr 3, iclass 3/1
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
uhid0: vendor 0x045e Microsoft Internet Keyboard Pro, rev 1.10/1.11, addr 3, iclass 3/1
Device configuration finished.
linprocfs registered
procfs registered
lapic: Divisor 2, Frequency 133000422 hz
Timecounter "TSC" frequency 1862010668 Hz quality -100
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
lo0: bpf attached
rr232x: no controller detected.
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on ICH7 chip
acd0: setting UDMA33 on ICH7 chip
acd0: <HL-DT-STDVD-ROM GDR8164B/0D08> DVDROM drive at ata0 as master
acd0: read 8268KB/s (8268KB/s), 256KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata2-slave: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad4: 76293MB <Seagate ST3808110AS 3.ADJ> at ata2-master SATA150
ad4: 156250000 sectors [155009C/16H/63S] 16 sectors/interrupt 1 depth queue
ad4: Intel check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ad5: 76293MB <Seagate ST3808110AS 3.ADJ> at ata2-slave SATA150
ad5: 156250000 sectors [155009C/16H/63S] 16 sectors/interrupt 1 depth queue
ad5: Intel check1 failed
ad5: Adaptec check1 failed
ad5: LSI (v3) check1 failed
ad5: LSI (v2) check1 failed
ad5: FreeBSD check1 failed
ATA PseudoRAID loaded
lapic1: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00008400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 4 to local APIC 1
ioapic0: Assigning ISA IRQ 6 to local APIC 0
ioapic0: Assigning ISA IRQ 9 to local APIC 1
ioapic0: Assigning ISA IRQ 14 to local APIC 0
ioapic0: Assigning ISA IRQ 15 to local APIC 1
ioapic0: Assigning PCI IRQ 16 to local APIC 0
ioapic0: Assigning PCI IRQ 18 to local APIC 1
ioapic0: Assigning PCI IRQ 20 to local APIC 0
ioapic0: Assigning PCI IRQ 21 to local APIC 1
ioapic0: Assigning PCI IRQ 22 to local APIC 0
ioapic0: Assigning PCI IRQ 23 to local APIC 1
GEOM: new disk ad4
GEOM: new disk ad5
GEOM_MIRROR: Device gm0 created (id=3212637885).
GEOM_MIRROR: Device gm0: provider ad4 detected.
GEOM_MIRROR: Device gm0: provider ad5 detected.
GEOM_MIRROR: Device gm0: provider ad5 activated.
GEOM_MIRROR: Device gm0: provider ad4 activated.
GEOM_MIRROR: Device gm0: provider mirror/gm0 launched.
Trying to mount root from ufs:/dev/mirror/gm0s1a
start_init: trying /sbin/init


More information about the freebsd-amd64 mailing list