Re: u-boot debug, was: Re: U-boot on RPI3, sees disk but won't boot it

On 2022-Sep-28, at 23:59, Mark Millard <marklmi@yahoo.com> wrote:

> On 2022-Sep-28, at 22:41, bob prohaska <fbsd@www.zefox.net> wrote:
> 
>> I've put the full output from a failed (no storage
>> device found) attempt at
>> http://www.zefox.net/~fbsd/rpi3/u-boot/u-boot-debug-log
>> 
>> The obvious error message is:
>> Cannot enable port 1 after 5 retries, disabling port.
>> Nothing about device 152d.
> 
> The RPi3B has 5 USB ports for devices, one being internal
> that is tied to the EtherNet port if I remember correctly.
> It also has a root hub,6 six overall.
> 
> Your failure log is about failing to get the root
> hub working --which in turn blocks all the other
> ports form being accessible.
> 
>> Tomorrow I'll try to capture a complete log of a 
>> successful boot for comparison. The boot success
>> rate is so far is 7 in 9 or 10, depending on how
>> one counts. 
> 
> I'd also recommend recording a bunch of failures
> and seeing what wort of variety exists in the
> details of them.
> 
> FYI: My log shows a Root Hub Port 1 status
> sequence: 511, 511, 503. Yours: 311, 311,
> (5 times:) 301. So it looks like what the
> status encoding is and what the implications
> are.

Accidental send. Continuing. . .

The output uses %x (so: hexadecimal). For reference:

./include/usb_defs.h:#define USB_PORT_STAT_CONNECTION    0x0001
./include/usb_defs.h:#define USB_PORT_STAT_ENABLE        0x0002
./include/usb_defs.h:#define USB_PORT_STAT_SUSPEND       0x0004
./include/usb_defs.h:#define USB_PORT_STAT_OVERCURRENT   0x0008
./include/usb_defs.h:#define USB_PORT_STAT_RESET         0x0010
./include/usb_defs.h:#define USB_PORT_STAT_POWER         0x0100
./include/usb_defs.h:#define USB_PORT_STAT_LOW_SPEED     0x0200
./include/usb_defs.h:#define USB_PORT_STAT_HIGH_SPEED    0x0400 /* support for EHCI */
./include/usb_defs.h:#define USB_PORT_STAT_SUPER_SPEED   0x0600 /* faking support to XHCI */
./include/usb_defs.h:#define USB_PORT_STAT_SPEED_MASK   \
./include/usb_defs.h:   (USB_PORT_STAT_LOW_SPEED | USB_PORT_STAT_HIGH_SPEED)
./include/usb_defs.h:#define USB_SS_PORT_STAT_MASK              (USB_PORT_STAT_CONNECTION | \
./include/usb_defs.h:                                    USB_PORT_STAT_ENABLE | \
./include/usb_defs.h:                                    USB_PORT_STAT_OVERCURRENT | \
./include/usb_defs.h:                                    USB_PORT_STAT_RESET)
./include/usb_defs.h:#define USB_PORT_STAT_C_CONNECTION  0x0001
./include/usb_defs.h:#define USB_PORT_STAT_C_ENABLE      0x0002
./include/usb_defs.h:#define USB_PORT_STAT_C_SUSPEND     0x0004
./include/usb_defs.h:#define USB_PORT_STAT_C_OVERCURRENT 0x0008
./include/usb_defs.h:#define USB_PORT_STAT_C_RESET       0x0010

Note: USB_PORT_STAT_C_* is for port status change information.

0x311 and 0x301 indicate USB_PORT_STAT_LOW_SPEED instead of
USB_PORT_STAT_HIGH_SPEED. They also indicate lack of
USB_PORT_STAT_ENABLE.


===
Mark Millard
marklmi at yahoo.com