any available patches for sata: "ad4: warning - setfeatures set
transfer mode taskqueue timeout - completing request directly"
dikshie
dikshie at gmail.com
Mon May 12 06:38:47 UTC 2008
On Mon, May 12, 2008 at 3:00 PM, Jeremy Chadwick <koitsu at freebsd.org> wrote:
> 1) Have you checked SMART statistics of the drive, or run SMART tests?
> Install ports/sysutils/smartmontools and use smartctl -a /dev/ad4, and
> provide the output.
>
> 2) Is the error always on ad4? If so, is the error always at LBA
> 4139103, or "around there" (give or take a few thousand addressing
> blocks)? If so, the ad4 disk may be going bad. Otherwise, I would say
> this is probably the issue I've documented on my Common Issues page.
dhcp-143-221# smartctl -a /dev/ad4
smartctl version 5.38 [amd64-portbld-freebsd7.0] Copyright (C) 2002-8
Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Second Generation Serial ATA family
Device Model: WDC WD3200AAKS-00VYA0
Serial Number: WD-WCARW2314765
Firmware Version: 12.01B02
User Capacity: 320,072,933,376 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon May 12 15:27:24 2008 JST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an
interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (8760) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 104) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0003 155 155 021 Pre-fail
Always - 5233
4 Start_Stop_Count 0x0032 100 100 000 Old_age
Always - 11
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000e 200 200 051 Old_age
Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age
Always - 940
10 Spin_Retry_Count 0x0012 100 253 051 Old_age
Always - 0
11 Calibration_Retry_Count 0x0012 100 253 051 Old_age
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 11
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age
Always - 8
193 Load_Cycle_Count 0x0032 200 200 000 Old_age
Always - 11
194 Temperature_Celsius 0x0022 114 108 000 Old_age
Always - 33
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 051 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
errors always on ad4 with random LBA blocks numbers.
with best regards,
-dikshie-
More information about the freebsd-stable
mailing list