Seagate HD not detected by FreeBSD

Ulf Magnusson ulfma629 at student.liu.se
Sat May 28 18:31:58 PDT 2005



----- Original Message -----
From: Vizion <vizion at vizion.occoxmail.com>
Date: Sunday, May 29, 2005 3:11 am
Subject: Re: Seagate HD not detected by FreeBSD
> On Saturday 28 May 2005 18:08,  the author Ulf Magnusson 
> contributed to the 
> dialogue on Re: Seagate HD not detected by FreeBSD:
> >From: Vizion <vizion at vizion.occoxmail.com>
> >
> >> On Saturday 28 May 2005 16:48,  the author Ulf Magnusson
> >> contributed to the
> >>
> >> dialogue on Seagate HD not detected by FreeBSD:
> >> >I'm trying to add a 120 GiB Seagate Barracuda (ST3120022A) HD. 
> I've>> >attached it as the sole device on IDE cable 2, jumpering it 
> as a
> >>
> >> slave>device. It is correctly detected by the BIOS as the Secondary
> >> Slave.>
> >>
> >> >The drive isn't detected by FreeBSD. There's no entry for it among
> >>
> >> the>dmesg messages, and no device node gets created. I've tried
> >> disabling>UDMA on the drive, to no avail.
> >>
> >> >System info:
> >> >
> >> >Epox Nforce2 motherboard
> >> >FreeBSD obygden 5.4-RELEASE FreeBSD 5.4-RELEASE #0: Wed May 11
> >>
> >> 17:32:06>CEST 2005     ulf at obygden:/usr/obj/usr/src/sys/DEB  i386
> >>
> >> >Parts of dmesg output:
> >> >
> >> >atapci0: <nVidia nForce2 UDMA133 controller> port
> >> >0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 9.0 on
> >>
> >> pci0>ata0: channel #0 on atapci0
> >>
> >> >ata1: channel #1 on atapci0
> >> >...
> >> >ad0: 38166MB <ST340014A/8.01> [77545/16/63] at ata0-master UDMA100
> >> >Mounting root from ufs:/dev/ad0s1a
> >> ><End of dmesg output>
> >>
> >> Can you please attach the full output from dmesg
> >>
> >> daid
> >
> >Copyright (c) 1992-2005 The FreeBSD Project.
> >Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 
> 1993, 1994
> >        The Regents of the University of California. All rights 
> reserved.>FreeBSD 5.4-RELEASE #0: Wed May 11 17:32:06 CEST 2005
> >    ulf at obygden:/usr/obj/usr/src/sys/DEB
> >Timecounter "i8254" frequency 1193182 Hz quality 0
> >CPU: AMD Athlon(tm) processor (1403.19-MHz 686-class CPU)
> >  Origin = "AuthenticAMD"  Id = 0x644  Stepping = 4
> >
>
>Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> >CM OV,PAT,PSE36,MMX,FXSR>
> >  AMD Features=0xc0440000<RSVD,AMIE,DSP,3DNow!>
> >real memory  = 536805376 (511 MB)
> >avail memory = 511438848 (487 MB)
> >mptable_probe: MP Config Table has bad signature:
> >ACPI APIC Table: <Nvidia AWRDACPI>
> >ioapic0 <Version 1.1> irqs 0-23 on motherboard
> >npx0: <math processor> on motherboard
> >npx0: INT 16 interface
> >acpi0: <Nvidia AWRDACPI> on motherboard
> >acpi0: Power Button (fixed)
> >Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> >acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on 
> acpi0>cpu0: <ACPI CPU> on acpi0
> >acpi_button0: <Power Button> on acpi0
> >pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> >pci0: <ACPI PCI bus> on pcib0
> >agp0: <NVIDIA nForce2 AGP Controller> mem 0xe0000000-0xe1ffffff at
> >device 0.0 on
> > pci0
> >pci0: <memory, RAM> at device 0.1 (no driver attached)
> >pci0: <memory, RAM> at device 0.2 (no driver attached)
> >pci0: <memory, RAM> at device 0.3 (no driver attached)
> >pci0: <memory, RAM> at device 0.4 (no driver attached)
> >pci0: <memory, RAM> at device 0.5 (no driver attached)
> >isab0: <PCI-ISA bridge> at device 1.0 on pci0
> >isa0: <ISA bus> on isab0
> >pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
> >ohci0: <OHCI (generic) USB controller> mem 0xe4001000-0xe4001fff 
> irq 22
> >at devic
> >e 2.0 on pci0
> >usb0: OHCI version 1.0, legacy support
> >usb0: <OHCI (generic) USB controller> on ohci0
> >usb0: USB revision 1.0
> >uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> >uhub0: 3 ports with 3 removable, self powered
> >ohci1: <OHCI (generic) USB controller> mem 0xe4004000-0xe4004fff 
> irq 21
> >at devic
> >e 2.1 on pci0
> >usb1: OHCI version 1.0, legacy support
> >usb1: <OHCI (generic) USB controller> on ohci1
> >usb1: USB revision 1.0
> >uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> >uhub1: 3 ports with 3 removable, self powered
> >pci0: <serial bus, USB> at device 2.2 (no driver attached)
> >pcib1: <ACPI PCI-PCI bridge> at device 8.0 on pci0
> >pci1: <ACPI PCI bus> on pcib1
> >xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xd000-0xd07f mem
> >0xe3000000-0xe300
> >007f irq 16 at device 8.0 on pci1
> >miibus0: <MII bus> on xl0
> >xlphy0: <3c905C 10/100 internal PHY> on miibus0
> >xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> >xl0: Ethernet address: 00:04:76:1c:4b:d1
> >pcm0: <Creative EMU10K1> port 0xd400-0xd41f irq 18 at device 10.0 
> on pci1
> >pcm0: <SigmaTel STAC9708/11 AC97 Codec>
> >atapci0: <nVidia nForce2 UDMA133 controller> port
> >0xf000-0xf00f,0x376,0x170-0x17
> >7,0x3f6,0x1f0-0x1f7 at device 9.0 on pci0
> >ata0: channel #0 on atapci0
> >ata1: channel #1 on atapci0
> >pci0: <serial bus, FireWire> at device 13.0 (no driver attached)
> >pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> >pci2: <ACPI PCI bus> on pcib2
> >nvidia0: <GeForce3> mem
> >0xdc000000-0xdc07ffff,0xd8000000-0xdbffffff,0xd0000000-0
> >xd0ffffff irq 19 at device 0.0 on pci2
> >acpi_tz0: <Thermal Zone> on acpi0
> >fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 
> on acpi0
> >fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> >sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 
> 0x10 on
> >acpi0
> >sio0: type 16550A
> >sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> >sio1: type 16550A
> >ppc0: <Standard parallel printer port> port 0x778-0x77b,0x378-
> 0x37f irq
> >7 on acp
> >i0
> >ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> >ppbus0: <Parallel port bus> on ppc0
> >lpt0: <Printer> on ppbus0
> >lpt0: Interrupt-driven port
> >atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> >atkbd0: <AT Keyboard> irq 1 on atkbdc0
> >kbd0 at atkbd0
> >pmtimer0 on isa0
> >orm0: <ISA Option ROMs> at iomem 0xcc000-0xcc7ff,0xc0000-0xcb7ff 
> on isa0
> >sc0: <System console> at flags 0x100 on isa0
> >sc0: VGA <16 virtual consoles, flags=0x300>
> >vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff 
> on isa0
> >ums0: Logitech USB-PS/2 Optical Mouse, rev 2.00/13.20, addr 2, 
> iclass 3/1
> >ums0: 4 buttons and Z dir.
> >Timecounter "TSC" frequency 1403190916 Hz quality 800
> >Timecounters tick every 10.000 msec
> >ad0: 38166MB <ST340014A/8.01> [77545/16/63] at ata0-master UDMA100
> >Mounting root from ufs:/dev/ad0s1a
> 
> OK your drive is recognized as at1 
> Here is the page from the handbook on www.freebsd.org - if you 
> follow the 
> instructions you should be OK:
> --------------------------------------------------------------------
> -------------------
> 16.3 Adding Disks
> Originally contributed by David O'Brien.
> 
> Lets say we want to add a new SCSI disk to a machine that currently 
> .......

Excuse me if I'm being slow, but exactly where did you glean that
information?
I don't have any at1 node in /dev, at1 isn't mentioned anywhere in the
boot messages, and Fdisk still acts like it only knows of one drive.

Ulf


More information about the freebsd-questions mailing list