Updates to freebsd-wifi-build
Piotr Kubaj
pkubaj at riseup.net
Mon May 18 07:54:17 UTC 2015
Hi, thanks for the effort, it's nice to see FreeBSD progress also on
MIPS. Are you going somewhen in the future make something like
release-arm-redux for MIPS?
Also, two years ago I asked about getting Mikrotik RB751G-2HnD to work
with FreeBSD (
https://lists.freebsd.org/pipermail/freebsd-mips/2013-May/002783.html ).
I now happily run OpenWRT on it, but would switch to FreeBSD, if
possible. Is there any hope about that? Below is my dmesg:
[ 0.000000] Linux version 3.10.49 (bb at builder1) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #5 Wed Oct 1 14:15:03 CEST 2014
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7242 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz,
Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 80326b60, node_mem_map
81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: no-uart parts=1
boot_part_size=4194304 gpio=3911 HZ=200000000 mem=64M
kmac=00:0C:42:F9:A7:C8 board=751g ver=3.22 hw_opt=00000105 boot=1 mlc=8
rootfstype=yaffs noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61148k/65536k available (2328k kernel code, 4388k
reserved, 634k data, 236k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is MikroTik RouterBOARD 751G
[ 0.100000] ar71xx: pll_reg 0xb805002c: 0x62000000
[ 0.340000] registering PCI controller with io_map_base unset
[ 0.350000] bio: create slab <bio-0> at 0
[ 0.360000] PCI host bridge to bus 0000:00
[ 0.360000] pci_bus 0000:00: root bus resource [mem
0x10000000-0x13ffffff]
[ 0.370000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.370000] pci_bus 0000:00: No busn resource found for root bus,
will use [bus 00-ff]
[ 0.380000] pci 0000:00:00.0: [168c:ff1c] type 00 class 0x020000
[ 0.380000] pci 0000:00:00.0: fixup device configuration
[ 0.380000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
[ 0.380000] pci 0000:00:00.0: supports D1
[ 0.380000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.380000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.380000] pci 0000:00:00.0: BAR 0: assigned [mem
0x10000000-0x1000ffff 64bit]
[ 0.390000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.390000] Switching to clocksource MIPS
[ 0.400000] NET: Registered protocol family 2
[ 0.400000] TCP established hash table entries: 512 (order: 0, 4096
bytes)
[ 0.410000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.420000] TCP: Hash tables configured (established 512 bind 512)
[ 0.420000] TCP: reno registered
[ 0.430000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.430000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.440000] NET: Registered protocol family 1
[ 0.440000] PCI: CLS 0 bytes, default 32
[ 0.470000] yaffs: yaffs built Sep 20 2014 23:09:53 Installing.
[ 0.470000] msgmni has been set to 119
[ 0.470000] io scheduler noop registered
[ 0.470000] io scheduler deadline registered (default)
[ 0.480000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.520000] console [ttyS0] enabled, bootconsole disabled
[ 0.650000] NAND flash driver for the RouterBOARD 750 version 0.1.0
[ 0.730000] NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST
Micro NAND 64MiB 3,3V 8-bit), 64MiB, page size: 512, OOB size: 16
[ 0.870000] Scanning device for bad blocks
[ 1.010000] Bad eraseblock 3831 at 0x000003bdc000
[ 1.070000] Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
[ 1.140000] 0x000000000000-0x000000040000 : "booter"
[ 1.200000] 0x000000040000-0x000000400000 : "kernel"
[ 1.270000] 0x000000400000-0x000004000000 : "rootfs"
[ 1.330000] mtd: device 2 (rootfs) set to be root filesystem
[ 1.400000] mtdsplit: no squashfs found in "rootfs"
[ 1.450000] mtdsplit: no squashfs found in "NAND 64MiB 3,3V 8-bit"
[ 1.560000] switch0: Atheros AR8327 rev. 2 switch registered on
ag71xx-mdio.0
[ 2.830000] libphy: ag71xx_mdio: probed
[ 3.430000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00
[uid=004dd033, driver=Atheros AR8216/AR8236/AR8316]
[ 3.560000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 3.630000] TCP: cubic registered
[ 3.670000] NET: Registered protocol family 17
[ 3.730000] Bridge firewalling registered
[ 3.780000] 8021q: 802.1Q VLAN Support v1.8
[ 3.830000] yaffs: dev is 32505858 name is "mtdblock2" ro
[ 3.890000] yaffs: passed flags ""
[ 3.930000] yaffs: yaffs: Attempting MTD mount of 31.2,"mtdblock2"
[ 4.020000] yaffs: block 3576 is bad
[ 5.160000] yaffs: yaffs_read_super: is_checkpointed 0
[ 5.160000] VFS: Mounted root (yaffs filesystem) readonly on device 31:2.
[ 5.240000] Freeing unused kernel memory: 236K (80345000 - 80380000)
[ 8.430000] eth0: link up (1000Mbps/Full duplex)
[ 9.680000] eth0: link down
[ 11.120000] NET: Registered protocol family 10
[ 11.180000] sit: IPv6 over IPv4 tunneling driver
[ 11.270000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
[ 11.410000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.490000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 11.580000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 11.670000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.780000] xt_time: kernel timezone is -0000
[ 11.870000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.970000] cfg80211: World regulatory domain updated:
[ 12.030000] cfg80211: DFS Master region: unset
[ 12.090000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.200000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 12.300000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 12.390000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
(N/A, 2000 mBm), (N/A)
[ 12.490000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (N/A)
[ 12.590000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 12.680000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 12.780000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 2000 mBm), (N/A)
[ 12.880000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 13.090000] PPP generic driver version 2.4.2
[ 13.140000] NET: Registered protocol family 24
[ 13.290000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 13.360000] ath: EEPROM regdomain: 0x0
[ 13.360000] ath: EEPROM indicates default country code should be used
[ 13.360000] ath: doing EEPROM country->regdmn map search
[ 13.360000] ath: country maps to regdmn code: 0x3a
[ 13.360000] ath: Country alpha2 being used: US
[ 13.360000] ath: Regpair used: 0x3a
[ 13.380000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.390000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[ 13.570000] cfg80211: Calling CRDA for country: US
[ 13.630000] cfg80211: Regulatory domain changed to country: US
[ 13.700000] cfg80211: DFS Master region: FCC
[ 13.750000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 13.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 3000 mBm), (N/A)
[ 13.960000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz),
(N/A, 1700 mBm), (N/A)
[ 14.050000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz),
(N/A, 2300 mBm), (0 s)
[ 14.150000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 3000 mBm), (N/A)
[ 14.250000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 22.330000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.610000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 22.690000] eth0: link up (1000Mbps/Full duplex)
[ 22.910000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.000000] device eth0.1 entered promiscuous mode
[ 23.060000] device eth0 entered promiscuous mode
[ 23.230000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 23.300000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.370000] br-lan: port 1(eth0.1) entered forwarding state
[ 24.780000] cfg80211: Calling CRDA to update world regulatory domain
[ 24.970000] cfg80211: Invalid regulatory domain detected:
[ 25.030000] cfg80211: Regulatory domain: 00
[ 25.080000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 25.200000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 25.290000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 25.390000] br-lan: port 1(eth0.1) entered forwarding state
[ 25.450000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
(N/A, 2000 mBm), (N/A)
[ 25.550000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (N/A)
[ 25.650000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 25.740000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 25.840000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 2000 mBm), (N/A)
[ 25.940000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 26.160000] cfg80211: Calling CRDA to update world regulatory domain
[ 26.450000] cfg80211: World regulatory domain updated:
[ 26.510000] cfg80211: DFS Master region: unset
[ 26.560000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 26.680000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 26.770000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 26.870000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
(N/A, 2000 mBm), (N/A)
[ 26.960000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (N/A)
[ 27.060000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 27.160000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 27.260000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 2000 mBm), (N/A)
[ 27.350000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 28.440000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.570000] device wlan0 entered promiscuous mode
[ 30.340000] br-lan: port 2(wlan0) entered forwarding state
[ 30.400000] br-lan: port 2(wlan0) entered forwarding state
[ 30.470000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 32.400000] br-lan: port 2(wlan0) entered forwarding state
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.freebsd.org/pipermail/freebsd-mips/attachments/20150518/fd8fadbc/attachment.sig>
More information about the freebsd-mips
mailing list