5.0.18 on 2.1.105 two controllers (MMAP Memory strangeness)

[Mark Anthony Lisher]

I have to scsi controlers (one on the motherboard). After upgrading to
5.0.18 the 'MMAP Memory' has changed to 0x0 were as on the 5.0.13 it was
0xcc800000 and scsi0 was at 0xcc802000.

Is this correct?

(scsi0) <Adaptec AIC-7880 Ultra SCSI host adapter> found at PCI 8/0
(scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs
(scsi0) BIOS enabled, IO Port 0xf800, IRQ 9
(scsi0) IO Memory at 0xfebfb000, MMAP Memory at 0xcc800000
(scsi0) Resetting channel
(scsi0) Downloading sequencer code... 413 instructions downloaded
(scsi1) <Adaptec AHA-2940A Ultra SCSI host adapter> found at PCI 13/0
(scsi1) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi1) BIOS enabled, IO Port 0xf400, IRQ 14
(scsi1) IO Memory at 0xfebfa000, MMAP Memory at 0x0
(scsi1) Resetting channel
(scsi1) Downloading sequencer code... 413 instructions downloaded

I have also been having the "Bad scbptr 255 during SELTO" problem

(scsi0:-1:-1:-1) Bad scbptr 255 during SELTO.
(scsi0:-1:-1:-1) Referenced SCB 255 not valid during SELTO.
        SCSISEQ = 0x12 SEQADDR = 0xb SSTAT0 = 0x15 SSTAT1 = 0x8a

and problems when boot with repeated resets.
I will send more information it required and am willing to try stuff out.

mal at dozy 1 ~ $ cat /proc/scsi/scsi 
Attached devices: 
Host: scsi0 Channel: 00 Id: 00 Lun: 00
  Vendor: CONNER   Model: CFP2107S  2.14GB Rev: 1524
  Type:   Direct-Access                    ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
  Vendor: MATSHITA Model: CD-ROM CR-506    Rev: 8S04
  Type:   CD-ROM                           ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
  Vendor: iomega   Model: jaz 1GB          Rev: J.83
  Type:   Direct-Access                    ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
  Vendor: PHILIPS  Model: CDD2600          Rev: 1.07
  Type:   CD-ROM                           ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 05 Lun: 00
  Vendor: IOMEGA   Model: ZIP 100          Rev: D.09
  Type:   Direct-Access                    ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
  Vendor: QUANTUM  Model: FIREBALL ST4.3S  Rev: 0F0C
  Type:   Direct-Access                    ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 06 Lun: 00
  Vendor: QUANTUM  Model: FIREBALL ST4.3S  Rev: 0F0C
  Type:   Direct-Access                    ANSI SCSI revision: 02
mal at dozy 2 ~ $ cat /proc/scsi/aic7xxx/0
Adaptec AIC7xxx driver version: 5.0.19/3.2.4
Compile Options:
  AIC7XXX_RESET_DELAY    : 5
  AIC7XXX_TAGGED_QUEUEING: Adapter Support Enabled
                             Check below to see which
                             devices use tagged queueing
  AIC7XXX_PAGE_ENABLE    : Enabled (This is no longer an option)
  AIC7XXX_PROC_STATS     : Disabled

Adapter Configuration:
           SCSI Adapter: Adaptec AIC-7880 Ultra SCSI host adapter
                           Ultra Narrow Controller
    PCI MMAPed I/O Base: 0xfebfb000
      Adaptec SCSI BIOS: Enabled
                    IRQ: 9
                   SCBs: Active 0, Max Active 1,
                         Allocated 30, HW 16, Page 255
             Interrupts: 4378
      BIOS Control Word: 0x18b6
   Adapter Control Word: 0x005e
   Extended Translation: Enabled
Disconnect Enable Flags: 0x00ff
     Ultra Enable Flags: 0x00f8
 Tag Queue Enable Flags: 0x0001
Ordered Queue Tag Flags: 0x0001
Default Tag Queue Depth: 8
    Tagged Queue By Device array for aic7xxx host instance 0:
      {1,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255}
    Actual queue depth per device for aic7xxx host instance 0:
      {1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
mal at dozy 3 ~ $ cat /proc/scsi/aic7xxx/1
Adaptec AIC7xxx driver version: 5.0.19/3.2.4
Compile Options:
  AIC7XXX_RESET_DELAY    : 5
  AIC7XXX_TAGGED_QUEUEING: Adapter Support Enabled
                             Check below to see which
                             devices use tagged queueing
  AIC7XXX_PAGE_ENABLE    : Enabled (This is no longer an option)
  AIC7XXX_PROC_STATS     : Disabled

Adapter Configuration:
           SCSI Adapter: Adaptec AHA-2940A Ultra SCSI host adapter
                           Ultra Narrow Controller
    Programmed I/O Base: f400
      Adaptec SCSI BIOS: Enabled
                    IRQ: 14
                   SCBs: Active 2, Max Active 2,
                         Allocated 30, HW 3, Page 255
             Interrupts: 23526
      BIOS Control Word: 0x18b6
   Adapter Control Word: 0x005e
   Extended Translation: Enabled
Disconnect Enable Flags: 0x00ff
     Ultra Enable Flags: 0x0041
 Tag Queue Enable Flags: 0x0041
Ordered Queue Tag Flags: 0x0041
Default Tag Queue Depth: 8
    Tagged Queue By Device array for aic7xxx host instance 1:
      {1,255,255,255,255,255,1,255,255,255,255,255,255,255,255,255}
    Actual queue depth per device for aic7xxx host instance 1:
      {1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
mal at dozy 4 ~ $ exit

  Mark
   ________________________________________________________________________
  |- Mark Anthony Lisher                       -|- icq: 1283233 markal    -|
  |- Coconut Software Limited                  -|- ---------------------- -|
  |- mal at coconut.co.uk                         -|- Home: markal at iname.com -|
  |- Tel: +44 1534 498051 Fax: +44 1534 490866 -|-       +44 1534 874682  -|
   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~







To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message