7890/aic7xxx 5.1.0pre5+3 --> pre6 success!

[Juergen Hammelmann]

Hallo Doug and the others!

Doug, I tested now your pre6 and it does well booting ;-)
with an asus p2b-ls, one ultrawide and two narrow devices.
One thing is different: with pre6 I get one timeout at the point, where
pre5 got in an infinite loop, after this one timeout it boots with
pre6 how you can see below...
the pre5+3 has never any timeouts.

:-) but pre6 does well

Juergen

------------------------------------------------------------------------
 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000f9a20
pcibios_init : BIOS32 Service Directory entry at 0xf0520
pcibios_init : PCI BIOS revision 2.10 entry at 0xf0550
Probing PCI hardware.
Calibrating delay loop.. ok - 299.83 BogoMIPS
Memory: 257096k/262144k available (712k kernel code, 384k reserved, 3952k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.35 (root at calculix.mathematik.uni-stuttgart.de) (gcc version 2.7.2.3) #2 Wed Aug 5 14:31:23 MEST 1998
Starting kswapd v 1.4.2.2 
APM BIOS version 1.2 Flags 0x03 (Driver version 1.2)
    Entry f000:7410 cseg16 f000 dseg fd8c cseg len ef7f, dseg len a0
    Connection version 1.1
    AC on line, battery status unknown, battery life unknown
    battery flag 0x80, battery life unknown
Real Time Clock Driver v1.09
Ramdisk driver initialized : 16 ramdisks of 4096K size
ide: i82371 PIIX (Triton) on PCI bus 0 function 33
ide: ports are not enabled (BIOS)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
(scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> found at PCI 6/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 407 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.0pre6/3.2.4
       <Adaptec AIC-7890/1 Ultra2 SCSI host adapter>
scsi : 1 host.
scsi : aborting command due to timeout : pid 1, scsi0, channel 0, id 0, lun 0 Inquiry 00 00 00 ff 00 
SCSI host 0 abort (pid 1) timed out - resetting
SCSI bus is being reset for host 0 channel 0.
  Vendor: IBM       Model: DDRS-39130W       Rev: S92A
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 15.
  Vendor: SCSI-CD   Model: ReWritable-2x2x6  Rev: 2.00
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
(scsi0:0:4:0) Synchronous at 10.0 Mbyte/sec, offset 15.
  Vendor: IOMEGA    Model: ZIP 100           Rev: E.08
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi removable disk sdb at scsi0, channel 0, id 5, lun 0
scsi : detected 1 SCSI cdrom 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17850000 [8715 MB] [8.7 GB]
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 28 
sdb : extended sense code = 2 
sdb : block size assumed to be 512 bytes, disk size 1GB.  
Partition check:
 sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 > sda3
 sdb:scsidisk I/O error: dev 08:10, sector 0, absolute sector 0
 unable to read partition table
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 128484k swap-space (priority -1)
Adding Swap: 128484k swap-space (priority -2)
Adding Swap: 128484k swap-space (priority -3)
Adding Swap: 128516k swap-space (priority -4)
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
scsi1 : interrupts not enabled. for better interactive performance,
scsi1 : please jumper the board for a free IRQ.
scsi1 : at port 0x240 interrupts disabled options CAN_QUEUE=16  CMD_PER_LUN=2 release=1 generic options AUTOPROBE_IRQ AUTOSENSE PSEUDO DMA USLEEP, USLEEP_POLL=1 USLEEP_SLEEP=20 generic release=7
scsi1 : Generic NCR5380/53C400 Driver
scsi : 2 hosts.
  Vendor: SCANNER   Model:                   Rev: 1.03
  Type:   Scanner                            ANSI SCSI revision: 01 CCS
Detected scsi generic sgd at scsi1, channel 0, id 6, lun 0



To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message