svn commit: r367889 - head/sbin/camcontrol

[Gordon Bergling]

Author: gbe (doc committer)
Date: Fri Nov 20 11:45:08 2020
New Revision: 367889
URL: https://svnweb.freebsd.org/changeset/base/367889

Log:
  camcontrol(8): Fix some warnings spotted by mandoc
  
  - skipping paragraph macro: Pp before Bl

Modified:
  head/sbin/camcontrol/camcontrol.8

Modified: head/sbin/camcontrol/camcontrol.8
==============================================================================
--- head/sbin/camcontrol/camcontrol.8	Fri Nov 20 11:31:25 2020	(r367888)
+++ head/sbin/camcontrol/camcontrol.8	Fri Nov 20 11:45:08 2020	(r367889)
@@ -2276,7 +2276,6 @@ These zones must be written sequentially.
 If they are not written sequentially, starting at the write pointer, the
 command will fail.
 .El
-.Pp
 .Bl -tag -width 12n
 .It Fl c Ar cmd
 Specify the zone subcommand:
@@ -2831,7 +2830,6 @@ This will read and decode the attribute values from pa
 in tape drive sa0, and will display any
 .Tn SCSI
 errors that result.
-.Pp
 .Bd -literal -offset indent
 camcontrol zone da0 -v -c rz -P summary
 .Ed
@@ -2842,7 +2840,6 @@ summary of the zone parameters, and display any
 or
 .Tn ATA
 errors that result.
-.Pp
 .Bd -literal -offset indent
 camcontrol zone da0 -v -c rz -o reset
 .Ed
@@ -2853,7 +2850,6 @@ pointer reset from the disk da0, and display any
 or
 .Tn ATA
 errors that result.
-.Pp
 .Bd -literal -offset indent
 camcontrol zone da0 -v -c rwp -l 0x2c80000
 .Ed
@@ -2864,7 +2860,6 @@ that starts at LBA 0x2c80000 and display any
 or
 .Tn ATA
 errors that result.
-.Pp
 .Bd -literal -offset indent
 camcontrol epc ada0 -c timer -T 60.1 -p Idle_a -e -s
 .Ed
@@ -2873,7 +2868,6 @@ Set the timer for the Idle_a power condition on drive
 .Pa ada0
 to 60.1 seconds, enable that particular power condition, and save the timer
 value and the enabled state of the power condition.
-.Pp
 .Bd -literal -offset indent
 camcontrol epc da4 -c goto -p Standby_z -H
 .Ed
@@ -2885,7 +2879,6 @@ the drive's lowest power state) and hold in that state
 explicitly released by another
 .Cm goto
 command.
-.Pp
 .Bd -literal -offset indent
 camcontrol epc da2 -c status -P
 .Ed
@@ -2903,7 +2896,6 @@ to only send the
 .Tn ATA
 CHECK POWER MODE command, which should not trigger a change in the drive's
 power state.
-.Pp
 .Bd -literal -offset indent
 camcontrol epc ada0 -c list
 .Ed
@@ -2911,7 +2903,6 @@ camcontrol epc ada0 -c list
 Display the ATA Power Conditions log (Log Address 0x08) for
 drive
 .Pa ada0 .
-.Pp
 .Bd -literal -offset indent
 camcontrol timestamp sa0 -s -f "%a, %d %b %Y %T %z" \e
 	-T "Wed, 26 Oct 2016 21:43:57 -0600"