svn commit: r209318 - in head/sys/mips/rmi: . dev/xlr
Jayachandran C.
jchandra at FreeBSD.org
Fri Jun 18 21:40:33 UTC 2010
Author: jchandra
Date: Fri Jun 18 21:40:32 2010
New Revision: 209318
URL: http://svn.freebsd.org/changeset/base/209318
Log:
Add support for newer XLS chips/boards in the GMAC driver.
Improved processor id code in board.h, remove unnecessary macros.
Approved by: rrs(mentor)
Modified:
head/sys/mips/rmi/board.c
head/sys/mips/rmi/board.h
head/sys/mips/rmi/dev/xlr/rge.c
Modified: head/sys/mips/rmi/board.c
==============================================================================
--- head/sys/mips/rmi/board.c Fri Jun 18 21:37:27 2010 (r209317)
+++ head/sys/mips/rmi/board.c Fri Jun 18 21:40:32 2010 (r209318)
@@ -100,6 +100,7 @@ xlr_board_info_setup()
xlr_board_info.is_xls = 1;
xlr_board_info.nr_cpus = 8;
xlr_board_info.usb = 1;
+ /* Board version 8 has NAND flash */
xlr_board_info.cfi =
(xlr_boot1_info.board_major_version != RMI_XLR_BOARD_ARIZONA_VIII);
xlr_board_info.pci_irq = 0;
@@ -114,7 +115,9 @@ xlr_board_info_setup()
xlr_board_info.gmac_block[0].credit_config = &xls_cc_table_gmac0;
xlr_board_info.gmac_block[0].station_txbase = MSGRNG_STNID_GMACTX0;
xlr_board_info.gmac_block[0].station_rfr = MSGRNG_STNID_GMACRFR_0;
- if (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_VI)
+ if (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_VI ||
+ xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_XI ||
+ xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_XII)
xlr_board_info.gmac_block[0].mode = XLR_PORT0_RGMII;
else
xlr_board_info.gmac_block[0].mode = XLR_SGMII;
@@ -125,12 +128,12 @@ xlr_board_info_setup()
/* network block 1 */
xlr_board_info.gmac_block[1].type = XLR_GMAC;
xlr_board_info.gmac_block[1].enabled = 0xf;
- if (xlr_is_xls4xx()) {
+ if (xlr_is_xls4xx_lite()) {
xlr_reg_t *mmio = xlr_io_mmio(XLR_IO_GPIO_OFFSET);
uint32_t tmp;
- /* some ports are not enabled on 4xx, figure this out
- from the GPIO fuse bank */
+ /* some ports are not enabled on the condor 4xx, figure this
+ out from the GPIO fuse bank */
tmp = xlr_read_reg(mmio, 35);
if (tmp & (1<<28))
xlr_board_info.gmac_block[1].enabled &= ~0x8;
Modified: head/sys/mips/rmi/board.h
==============================================================================
--- head/sys/mips/rmi/board.h Fri Jun 18 21:37:27 2010 (r209317)
+++ head/sys/mips/rmi/board.h Fri Jun 18 21:40:32 2010 (r209318)
@@ -26,10 +26,16 @@
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
- * RMI_BSD */
+ * RMI_BSD
+ * $FreeBSD$
+ */
#ifndef _RMI_BOARD_H_
#define _RMI_BOARD_H_
+/*
+ * Engineering boards have a major/minor number in their EEPROM to
+ * identify their configuration
+ */
#define RMI_XLR_BOARD_ARIZONA_I 1
#define RMI_XLR_BOARD_ARIZONA_II 2
#define RMI_XLR_BOARD_ARIZONA_III 3
@@ -38,95 +44,34 @@
#define RMI_XLR_BOARD_ARIZONA_VI 6
#define RMI_XLR_BOARD_ARIZONA_VII 7
#define RMI_XLR_BOARD_ARIZONA_VIII 8
+#define RMI_XLR_BOARD_ARIZONA_XI 11
+#define RMI_XLR_BOARD_ARIZONA_XII 12
-#define RMI_CHIP_XLR308_A0 0x0c0600
-#define RMI_CHIP_XLR508_A0 0x0c0700
-#define RMI_CHIP_XLR516_A0 0x0c0800
-#define RMI_CHIP_XLR532_A0 0x0c0900
-#define RMI_CHIP_XLR716_A0 0x0c0a00
-#define RMI_CHIP_XLR732_A0 0x0c0b00
-
-#define RMI_CHIP_XLR308_A1 0x0c0601
-#define RMI_CHIP_XLR508_A1 0x0c0701
-#define RMI_CHIP_XLR516_A1 0x0c0801
-#define RMI_CHIP_XLR532_A1 0x0c0901
-#define RMI_CHIP_XLR716_A1 0x0c0a01
-#define RMI_CHIP_XLR732_A1 0x0c0b01
-
-#define RMI_CHIP_XLR308_B0 0x0c0602
-#define RMI_CHIP_XLR508_B0 0x0c0702
-#define RMI_CHIP_XLR516_B0 0x0c0802
-#define RMI_CHIP_XLR532_B0 0x0c0902
-#define RMI_CHIP_XLR716_B0 0x0c0a02
-#define RMI_CHIP_XLR732_B0 0x0c0b02
-
-#define RMI_CHIP_XLR308_B1 0x0c0603
-#define RMI_CHIP_XLR508_B1 0x0c0703
-#define RMI_CHIP_XLR516_B1 0x0c0803
-#define RMI_CHIP_XLR532_B1 0x0c0903
-#define RMI_CHIP_XLR716_B1 0x0c0a03
-#define RMI_CHIP_XLR732_B1 0x0c0b03
-
-#define RMI_CHIP_XLR308_B2 0x0c0604
-#define RMI_CHIP_XLR508_B2 0x0c0704
-#define RMI_CHIP_XLR516_B2 0x0c0804
-#define RMI_CHIP_XLR532_B2 0x0c0904
-#define RMI_CHIP_XLR716_B2 0x0c0a04
-#define RMI_CHIP_XLR732_B2 0x0c0b04
-
-#define RMI_CHIP_XLR308_C0 0x0c0705
-#define RMI_CHIP_XLR508_C0 0x0c0b05
-#define RMI_CHIP_XLR516_C0 0x0c0a05
-#define RMI_CHIP_XLR532_C0 0x0c0805
-#define RMI_CHIP_XLR716_C0 0x0c0205
-#define RMI_CHIP_XLR732_C0 0x0c0005
-
-#define RMI_CHIP_XLR308_C1 0x0c0706
-#define RMI_CHIP_XLR508_C1 0x0c0b06
-#define RMI_CHIP_XLR516_C1 0x0c0a06
-#define RMI_CHIP_XLR532_C1 0x0c0806
-#define RMI_CHIP_XLR716_C1 0x0c0206
-#define RMI_CHIP_XLR732_C1 0x0c0006
-
-#define RMI_CHIP_XLR308_C2 0x0c0707
-#define RMI_CHIP_XLR508_C2 0x0c0b07
-#define RMI_CHIP_XLR516_C2 0x0c0a07
-#define RMI_CHIP_XLR532_C2 0x0c0807
-#define RMI_CHIP_XLR716_C2 0x0c0207
-#define RMI_CHIP_XLR732_C2 0x0c0007
-
-#define RMI_CHIP_XLR308_C3 0x0c0708
-#define RMI_CHIP_XLR508_C3 0x0c0b08
-#define RMI_CHIP_XLR516_C3 0x0c0a08
-#define RMI_CHIP_XLR532_C3 0x0c0808
-#define RMI_CHIP_XLR716_C3 0x0c0208
-#define RMI_CHIP_XLR732_C3 0x0c0008
-
-#define RMI_CHIP_XLR308_C4 0x0c0709
-#define RMI_CHIP_XLR508_C4 0x0c0b09
-#define RMI_CHIP_XLR516_C4 0x0c0a09
-#define RMI_CHIP_XLR532_C4 0x0c0809
-#define RMI_CHIP_XLR716_C4 0x0c0209
-#define RMI_CHIP_XLR732_C4 0x0c0009
-
-#define RMI_CHIP_XLS608_A0 0x0c8000
-#define RMI_CHIP_XLS408_A0 0x0c8800
-#define RMI_CHIP_XLS404_A0 0x0c8c00
-#define RMI_CHIP_XLS208_A0 0x0c8e00
-#define RMI_CHIP_XLS204_A0 0x0c8f00
-
-#define RMI_CHIP_XLS608_A1 0x0c8001
-#define RMI_CHIP_XLS408_A1 0x0c8801
-#define RMI_CHIP_XLS404_A1 0x0c8c01
-#define RMI_CHIP_XLS208_A1 0x0c8e01
-#define RMI_CHIP_XLS204_A1 0x0c8f01
-
-static __inline__ unsigned int
-xlr_revision(void)
-{
- return mips_rd_prid() & 0xff00ff;
-}
-
+/*
+ * RMI Chips - Values in Processor ID field
+ */
+#define RMI_CHIP_XLR732 0x00
+#define RMI_CHIP_XLR716 0x02
+#define RMI_CHIP_XLR308 0x06
+#define RMI_CHIP_XLR532 0x09
+
+#define RMI_CHIP_XLS616_B0 0x40
+#define RMI_CHIP_XLS608_B0 0x4a
+#define RMI_CHIP_XLS608 0x80 /* Internal */
+#define RMI_CHIP_XLS416_B0 0x44
+#define RMI_CHIP_XLS412_B0 0x4c
+#define RMI_CHIP_XLS408_B0 0x4e
+#define RMI_CHIP_XLS408 0x88 /* Lite "Condor" */
+#define RMI_CHIP_XLS404_B0 0x4f
+#define RMI_CHIP_XLS404 0x8c /* Lite "Condor" */
+#define RMI_CHIP_XLS208 0x8e
+#define RMI_CHIP_XLS204 0x8f
+#define RMI_CHIP_XLS108 0xce
+#define RMI_CHIP_XLS104 0xcf
+
+/*
+ * The XLS product line has chip versions 0x4x and 0x8x
+ */
static __inline__ unsigned int
xlr_is_xls(void)
{
@@ -135,122 +80,60 @@ xlr_is_xls(void)
return (prid & 0xf000) == 0x8000 || (prid & 0xf000) == 0x4000;
}
-static __inline__ int
-xlr_revision_a0(void)
-{
- return xlr_revision() == 0x0c0000;
-}
-
-static __inline__ int
-xlr_revision_b0(void)
-{
- return xlr_revision() == 0x0c0002;
-}
-
-static __inline__ int
-xlr_revision_b1(void)
-{
- return xlr_revision() == 0x0c0003;
-}
-
-static __inline__ int
-xlr_board_atx_i(void)
-{
- return xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_I;
-}
-
-static __inline__ int
-xlr_board_atx_ii(void)
-{
- return xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_II;
-}
-
-static __inline__ int
-xlr_board_atx_ii_b(void)
-{
- return (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_II)
- && (xlr_boot1_info.board_minor_version == 1);
-}
-
-static __inline__ int
-xlr_board_atx_iii(void)
-{
- return xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_III;
-}
-
-static __inline__ int
-xlr_board_atx_iv(void)
-{
- return (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_IV)
- && (xlr_boot1_info.board_minor_version == 0);
-}
-static __inline__ int
-xlr_board_atx_iv_b(void)
-{
- return (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_IV)
- && (xlr_boot1_info.board_minor_version == 1);
-}
-static __inline__ int
-xlr_board_atx_v(void)
-{
- return xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_V;
-}
-static __inline__ int
-xlr_board_atx_vi(void)
-{
- return xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_VI;
-}
-
-static __inline__ int
-xlr_board_atx_iii_256(void)
-{
- return (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_III)
- && (xlr_boot1_info.board_minor_version == 0);
-}
-
-static __inline__ int
-xlr_board_atx_iii_512(void)
+/*
+ * The last byte of the processor id field is revision
+ */
+static __inline__ unsigned int
+xlr_revision(void)
{
- return (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_III)
- && (xlr_boot1_info.board_minor_version == 1);
+ return mips_rd_prid() & 0xff;
}
-static __inline__ int
-xlr_board_atx_v_512(void)
+/*
+ * The 15:8 byte of the PR Id register is the Processor ID
+ */
+static __inline__ unsigned int
+xlr_processor_id(void)
{
- return (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_V)
- && (xlr_boot1_info.board_minor_version == 1);
+ return ((mips_rd_prid() & 0xff00) >> 8);
}
+/*
+ * RMI Engineering boards which are PCI cards
+ * These should come up in PCI device mode (not yet)
+ */
static __inline__ int
xlr_board_pci(void)
{
- return (xlr_board_atx_iii_256() || xlr_board_atx_iii_512()
- || xlr_board_atx_v_512());
+ return ((xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_III) ||
+ (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_V));
}
+
static __inline__ int
xlr_is_xls2xx(void)
{
- uint32_t chipid = mips_rd_prid() & 0xffffff00U;
+ uint32_t chipid = xlr_processor_id();
- return chipid == 0x0c8e00 || chipid == 0x0c8f00;
+ return (chipid == 0x8e || chipid == 0x8f);
}
static __inline__ int
-xlr_is_xls4xx(void)
+xlr_is_xls4xx_lite(void)
{
- uint32_t chipid = mips_rd_prid() & 0xffffff00U;
+ uint32_t chipid = xlr_processor_id();
- return chipid == 0x0c8800 || chipid == 0x0c8c00;
+ return (chipid == 0x88 || chipid == 0x8c);
}
/* all our knowledge of chip and board that cannot be detected run-time goes here */
enum gmac_block_types {
XLR_GMAC, XLR_XGMAC, XLR_SPI4
};
+
enum gmac_block_modes {
XLR_RGMII, XLR_SGMII, XLR_PORT0_RGMII
};
+
struct xlr_board_info {
int is_xls;
int nr_cpus;
@@ -273,7 +156,7 @@ struct xlr_board_info {
int baseirq; /* first irq for this block, the rest are in
* sequence */
int baseinst; /* the first rge unit for this block */
- } gmac_block[3];
+ } gmac_block[3];
};
extern struct xlr_board_info xlr_board_info;
Modified: head/sys/mips/rmi/dev/xlr/rge.c
==============================================================================
--- head/sys/mips/rmi/dev/xlr/rge.c Fri Jun 18 21:37:27 2010 (r209317)
+++ head/sys/mips/rmi/dev/xlr/rge.c Fri Jun 18 21:40:32 2010 (r209318)
@@ -899,7 +899,6 @@ static void
serdes_regs_init(struct driver_data *priv)
{
xlr_reg_t *mmio_gpio = (xlr_reg_t *) (xlr_io_base + XLR_IO_GPIO_OFFSET);
- int i;
/* Initialize SERDES CONTROL Registers */
rge_mii_write_internal(priv->serdes_mmio, 26, 0, 0x6DB0);
@@ -915,14 +914,27 @@ serdes_regs_init(struct driver_data *pri
rge_mii_write_internal(priv->serdes_mmio, 26, 10, 0x0000);
/*
- * For loop delay and GPIO programming crud from Linux driver,
+ * GPIO setting which affect the serdes - needs figuring out
*/
- for (i = 0; i < 10000000; i++) {
- }
- mmio_gpio[0x20] = 0x7e6802;
- mmio_gpio[0x10] = 0x7104;
- for (i = 0; i < 100000000; i++) {
+ DELAY(100);
+ xlr_write_reg(mmio_gpio, 0x20, 0x7e6802);
+ xlr_write_reg(mmio_gpio, 0x10, 0x7104);
+ DELAY(100);
+
+ /*
+ * This kludge is needed to setup serdes (?) clock correctly on some
+ * XLS boards
+ */
+ if ((xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_XI ||
+ xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_XII) &&
+ xlr_boot1_info.board_minor_version == 4) {
+ /* use 125 Mhz instead of 156.25Mhz ref clock */
+ DELAY(100);
+ xlr_write_reg(mmio_gpio, 0x10, 0x7103);
+ xlr_write_reg(mmio_gpio, 0x21, 0x7103);
+ DELAY(100);
}
+
return;
}
@@ -1085,7 +1097,7 @@ rmi_xlr_gmac_config_speed(struct driver_
if (priv->speed == xlr_mac_speed_10) {
if (priv->mode != XLR_RGMII)
xlr_write_reg(mmio, R_INTERFACE_CONTROL, SGMII_SPEED_10);
- xlr_write_reg(mmio, R_MAC_CONFIG_2, 0x7137);
+ xlr_write_reg(mmio, R_MAC_CONFIG_2, 0x7117);
xlr_write_reg(mmio, R_CORECONTROL, 0x02);
printf("%s: [10Mbps]\n", device_get_nameunit(sc->rge_dev));
sc->rge_mii.mii_media.ifm_media = IFM_ETHER | IFM_AUTO | IFM_10_T | IFM_FDX;
@@ -1094,7 +1106,7 @@ rmi_xlr_gmac_config_speed(struct driver_
} else if (priv->speed == xlr_mac_speed_100) {
if (priv->mode != XLR_RGMII)
xlr_write_reg(mmio, R_INTERFACE_CONTROL, SGMII_SPEED_100);
- xlr_write_reg(mmio, R_MAC_CONFIG_2, 0x7137);
+ xlr_write_reg(mmio, R_MAC_CONFIG_2, 0x7117);
xlr_write_reg(mmio, R_CORECONTROL, 0x01);
printf("%s: [100Mbps]\n", device_get_nameunit(sc->rge_dev));
sc->rge_mii.mii_media.ifm_media = IFM_ETHER | IFM_AUTO | IFM_100_TX | IFM_FDX;
@@ -1105,7 +1117,7 @@ rmi_xlr_gmac_config_speed(struct driver_
if (priv->mode != XLR_RGMII)
xlr_write_reg(mmio, R_INTERFACE_CONTROL, SGMII_SPEED_100);
printf("PHY reported unknown MAC speed, defaulting to 100Mbps\n");
- xlr_write_reg(mmio, R_MAC_CONFIG_2, 0x7137);
+ xlr_write_reg(mmio, R_MAC_CONFIG_2, 0x7117);
xlr_write_reg(mmio, R_CORECONTROL, 0x01);
sc->rge_mii.mii_media.ifm_media = IFM_ETHER | IFM_AUTO | IFM_100_TX | IFM_FDX;
sc->rge_mii.mii_media.ifm_cur->ifm_media = IFM_ETHER | IFM_AUTO | IFM_100_TX | IFM_FDX;
@@ -1113,7 +1125,7 @@ rmi_xlr_gmac_config_speed(struct driver_
} else {
if (priv->mode != XLR_RGMII)
xlr_write_reg(mmio, R_INTERFACE_CONTROL, SGMII_SPEED_1000);
- xlr_write_reg(mmio, R_MAC_CONFIG_2, 0x7237);
+ xlr_write_reg(mmio, R_MAC_CONFIG_2, 0x7217);
xlr_write_reg(mmio, R_CORECONTROL, 0x00);
printf("%s: [1000Mbps]\n", device_get_nameunit(sc->rge_dev));
sc->rge_mii.mii_media.ifm_media = IFM_ETHER | IFM_AUTO | IFM_1000_T | IFM_FDX;
@@ -1788,7 +1800,9 @@ rge_attach(device_t dev)
priv->instance = priv->id - xlr_board_info.gmacports;
priv->mmio = (xlr_reg_t *) (xlr_io_base + gmac_conf->baseaddr);
}
- if (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_VI) {
+ if (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_VI ||
+ (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_XI &&
+ priv->instance >=4)) {
dbg_msg("Arizona board - offset 4 \n");
priv->mii_mmio = (xlr_reg_t *) (xlr_io_base + XLR_IO_GMAC_4_OFFSET);
} else
@@ -1812,7 +1826,9 @@ rge_attach(device_t dev)
priv->mode = gmac_conf->mode;
if (xlr_board_info.is_xls == 0) {
- if (xlr_board_atx_ii() && !xlr_board_atx_ii_b())
+ /* TODO - check II and IIB boards */
+ if (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_II &&
+ xlr_boot1_info.board_minor_version != 1)
priv->phy_addr = priv->instance - 2;
else
priv->phy_addr = priv->instance;
@@ -1824,7 +1840,12 @@ rge_attach(device_t dev)
priv->phy_addr = 0;
} else {
priv->mode = XLR_SGMII;
- priv->phy_addr = priv->instance + 16;
+ /* Board 11 has SGMII daughter cards with the XLS chips, in this case
+ the phy number is 0-3 for both GMAC blocks */
+ if (xlr_boot1_info.board_major_version == RMI_XLR_BOARD_ARIZONA_XI)
+ priv->phy_addr = priv->instance % 4 + 16;
+ else
+ priv->phy_addr = priv->instance + 16;
}
}
@@ -2088,8 +2109,8 @@ rge_intr(void *arg)
/* clear all interrupts and hope to make progress */
xlr_write_reg(mmio, R_INTREG, 0xffffffff);
- /* on A0 and B0, xgmac interrupts are routed only to xgs_1 irq */
- if ((xlr_revision_b0()) && (priv->type == XLR_XGMAC)) {
+ /* (not yet) on A0 and B0, xgmac interrupts are routed only to xgs_1 irq */
+ if ((xlr_revision() < 2) && (priv->type == XLR_XGMAC)) {
struct rge_softc *xgs0_dev = dev_mac[dev_mac_xgs0];
struct driver_data *xgs0_priv = &xgs0_dev->priv;
xlr_reg_t *xgs0_mmio = xgs0_priv->mmio;
More information about the svn-src-all
mailing list