ASUS P5B-MX + 6.2-STABLE + xf86-video-intel

Yousif Hassan yousif at alumni.jmu.edu
Mon Sep 24 06:35:41 PDT 2007 

Can't really tell from what you've sent if you've enabled/loaded "device
agp".  Either put that in your kernel, or kldload it.  I believe modern
Intel cards require this.

On Mon, 2007-09-24 at 15:02 +0200, vermaden wrote:
> Long story short.
> 
> Can not get intel driver (from xf86-video-intel 2.1.1) to work with Asus P5B-MX IGA.
> 
> vesa driver works, but that is not the point here...
> 
> kernel config: GENERIC
> 
> # uname -a
> FreeBSD siewa 6.2-STABLE FreeBSD 6.2-STABLE #0: Mon Sep 24 12:58:17 CEST 2007     root at siewa:/usr/obj/usr/src/sys/CUSTOM  i386
> 
> # kldstat
> Id Refs Address    Size     Name
>  1   12 0xc0400000 7cfd04   kernel
>  2    1 0xc0bd0000 6348c    acpi.ko
>  3    1 0xc52b1000 1c000    linux.ko
>  4    1 0xc5543000 6000     i915.ko
>  5    1 0xc5549000 f000     drm.ko
> 
> # dmesg
> Copyright (c) 1992-2007 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 6.2-STABLE #0: Mon Sep 24 12:58:17 CEST 2007
>     root at siewa:/usr/obj/usr/src/sys/CUSTOM
> ACPI APIC Table: <A_M_I_ OEMAPIC >
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Genuine Intel(R) CPU            2160  @ 1.80GHz (1800.01-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x6f2  Stepping = 2
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0xe39d<SSE3,RSVD2,MON,DS_CPL,EST,TM2,<b9>,CX16,<b14>,<b15>>
>   AMD Features=0x20100000<NX,LM>
>   AMD Features2=0x1<LAHF>
>   Cores per package: 2
> real memory  = 1064960000 (1015 MB)
> avail memory = 1028931584 (981 MB)
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> acpi0: <A_M_I_ OEMRSDT> on motherboard
> acpi0: Power Button (fixed)
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
> cpu0: <ACPI CPU> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pci0: <display, VGA> at device 2.0 (no driver attached)
> pci0: <multimedia> at device 27.0 (no driver attached)
> uhci0: <UHCI (generic) USB controller> port 0xd400-0xd41f irq 23 at device 29.0 on pci0
> uhci0: [GIANT-LOCKED]
> usb0: <UHCI (generic) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <UHCI (generic) USB controller> port 0xd480-0xd49f irq 19 at device 29.1 on pci0
> uhci1: [GIANT-LOCKED]
> usb1: <UHCI (generic) USB controller> on uhci1
> usb1: USB revision 1.0
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <UHCI (generic) USB controller> port 0xd800-0xd81f irq 18 at device 29.2 on pci0
> uhci2: [GIANT-LOCKED]
> usb2: <UHCI (generic) USB controller> on uhci2
> usb2: USB revision 1.0
> uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> uhci3: <UHCI (generic) USB controller> port 0xd880-0xd89f irq 16 at device 29.3 on pci0
> uhci3: [GIANT-LOCKED]
> usb3: <UHCI (generic) USB controller> on uhci3
> usb3: USB revision 1.0
> uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub3: 2 ports with 2 removable, self powered
> ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfe9f7c00-0xfe9f7fff irq 23 at device 29.7 on pci0
> ehci0: [GIANT-LOCKED]
> usb4: EHCI version 1.0
> usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
> usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
> usb4: USB revision 2.0
> uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub4: 8 ports with 8 removable, self powered
> pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem 0xfebffc00-0xfebffcff irq 19 at device 0.0 on pci1
> miibus0: <MII bus> on rl0
> rlphy0: <RealTek internal media interface> on miibus0
> rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl0: Ethernet address: 00:90:cc:de:5e:0c
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH7 UDMA100 controller> port 0xc480-0xc487,0xc400-0xc403,0x8f0-0x8f7,0x8f8-0x8fb,0xbc00-0xbc0f irq 18 at device 31.1 on pci0
> ata2: <ATA channel 0> on atapci0
> ata3: <ATA channel 1> on atapci0
> atapci1: <Intel ICH7 SATA300 controller> port 0xd080-0xd087,0xd000-0xd003,0xcc00-0xcc07,0xc880-0xc883,0xc800-0xc80f irq 19 at device 31.2 on pci0
> ata4: <ATA channel 0> on atapci1
> ata5: <ATA channel 1> on atapci1
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> acpi_button0: <Power Button> on acpi0
> ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/9 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: [GIANT-LOCKED]
> psm0: model IntelliMouse, device ID 3
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> sio0: type 16550A
> pmtimer0 on isa0
> orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0
> ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
> ata1 at port 0x170-0x177,0x376 irq 15 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Timecounter "TSC" frequency 1800012429 Hz quality 800
> Timecounters tick every 1.000 msec
> acd0: CDROM <SAMSUNG CD-ROM SC-148S/SS03> at ata2-slave PIO4
> ad8: 152627MB <WDC WD1600JS-60MHB5 10.02E04> at ata4-master SATA150
> Trying to mount root from ufs:/dev/ad8s1a
> 
> # pciconf -lv
> hostb0 at pci0:0:0:        class=0x060000 card=0x823b1043 chip=0x29708086 rev=0x02 hdr=0x00
>     vendor     = 'Intel Corporation'
>     class      = bridge
>     subclass   = HOST-PCI
> none0 at pci0:2:0: class=0x030000 card=0x823b1043 chip=0x29728086 rev=0x02 hdr=0x00
>     vendor     = 'Intel Corporation'
>     class      = display
>     subclass   = VGA
> none1 at pci0:27:0:        class=0x040300 card=0x82901043 chip=0x27d88086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801G (ICH7 Family) High Definition Audio'
>     class      = multimedia
> uhci0 at pci0:29:0:        class=0x0c0300 card=0x81791043 chip=0x27c88086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801G (ICH7 Family) USB Universal Host Controller'
>     class      = serial bus
>     subclass   = USB
> uhci1 at pci0:29:1:        class=0x0c0300 card=0x81791043 chip=0x27c98086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801G (ICH7 Family) USB Universal Host Controller'
>     class      = serial bus
>     subclass   = USB
> uhci2 at pci0:29:2:        class=0x0c0300 card=0x81791043 chip=0x27ca8086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801G (ICH7 Family) USB Universal Host Controller'
>     class      = serial bus
>     subclass   = USB
> uhci3 at pci0:29:3:        class=0x0c0300 card=0x81791043 chip=0x27cb8086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801G (ICH7 Family) USB Universal Host Controller'
>     class      = serial bus
>     subclass   = USB
> ehci0 at pci0:29:7:        class=0x0c0320 card=0x81791043 chip=0x27cc8086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801G (ICH7 Family) USB 2.0 Enhanced Host Controller'
>     class      = serial bus
>     subclass   = USB
> pcib1 at pci0:30:0:        class=0x060401 card=0x81791043 chip=0x244e8086 rev=0xe1 hdr=0x01
>     vendor     = 'Intel Corporation'
>     device     = '82801BA/CA/DB/DBL/EB/ER/FB (ICH2/3/4/4/5/5/6), 6300ESB Hub Interface to PCI Bridge'
>     class      = bridge
>     subclass   = PCI-PCI
> isab0 at pci0:31:0:        class=0x060100 card=0x81791043 chip=0x27b88086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801GB/GR (ICH7 Family) LPC Interface Controller'
>     class      = bridge
>     subclass   = PCI-ISA
> atapci0 at pci0:31:1:      class=0x01018f card=0x81791043 chip=0x27df8086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801G (ICH7 Family) Ultra ATA Storage Controller'
>     class      = mass storage
>     subclass   = ATA
> atapci1 at pci0:31:2:      class=0x01018f card=0x81791043 chip=0x27c08086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller'
>     class      = mass storage
>     subclass   = ATA
> none2 at pci0:31:3:        class=0x0c0500 card=0x81791043 chip=0x27da8086 rev=0x01 hdr=0x00
>     vendor     = 'Intel Corporation'
>     device     = '82801G (ICH7 Family) SMBus Controller'
>     class      = serial bus
>     subclass   = SMBus
> rl0 at pci1:0:0:   class=0x020000 card=0x10015354 chip=0x813910ec rev=0x10 hdr=0x00
>     vendor     = 'Realtek Semiconductor'
>     device     = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter'
>     class      = network
>     subclass   = ethernet
> 
> 
> # cat /etc/X11/xorg.conf
> Section "ServerLayout"
> 	Identifier     "X.org Configured"
> 	Screen      0  "Screen0" 0 0
> 	InputDevice    "Mouse0" "CorePointer"
> 	InputDevice    "Keyboard0" "CoreKeyboard"
> EndSection
> 
> Section "Files"
> 	RgbPath      "/usr/local/share/X11/rgb"
> 	ModulePath   "/usr/local/lib/xorg/modules"
> EndSection
> 
> Section "Module"
>         Load  "dri"
>         Load  "glx"
> 	Load  "dbe"
> 	Load  "extmod"
> EndSection
> 
> Section "InputDevice"
> 	Identifier  "Keyboard0"
> 	Driver      "kbd"
> EndSection
> 
> Section "InputDevice"
> 	Identifier  "Mouse0"
> 	Driver      "mouse"
> 	Option	    "Protocol" "auto"
> 	Option	    "Device" "/dev/sysmouse"
> EndSection
> 
> Section "Monitor"
> 	Identifier   "Monitor0"
> 	HorizSync    30.0 - 83.0
> 	VertRefresh  55.0 - 75.0
> 	Option	    "DPMS"
> EndSection
> 
> Section "Device"
> 	Identifier  "Card0"
> 	Driver      "intel"
> EndSection
> 
> Section "Screen"
> 	Identifier "Screen0"
> 	Device     "Card0"
> 	Monitor    "Monitor0"
>         DefaultDepth 24
> 	SubSection "Display"
> 		Depth 24
> 		Modes "1280x1024"
> 	EndSubSection
> EndSection
> 
> % startx (as user)
> xddc64f78f1b2b3b2d02454c8cd0c339c: not found
> xauth:  creating new authority file /home/vermaden/.serverauth.860
> 
> 
> X Window System Version 7.2.0
> Release Date: 22 January 2007
> X Protocol Version 11, Revision 0, Release 7.2
> Build Operating System: FreeBSD 6.2-STABLE i386 
> Current Operating System: FreeBSD siewa 6.2-STABLE FreeBSD 6.2-STABLE #0: Mon Sep 24 12:58:17 CEST 2007     root at siewa:/usr/obj/usr/src/sys/CUSTOM i386
> Build Date: 31 July 2007
> 	Before reporting problems, check http://wiki.x.org
> 	to make sure that you have the latest version.
> Module Loader present
> Markers: (--) probed, (**) from config file, (==) default setting,
> 	(++) from command line, (!!) notice, (II) informational,
> 	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
> (==) Log file: "/var/log/Xorg.0.log", Time: Mon Sep 24 14:55:11 2007
> (==) Using config file: "/etc/X11/xorg.conf"
> (EE) GARTInit: Unable to open /dev/agpgart (No such file or directory)
> (EE) intel(0): Failed to allocate framebuffer. Is your VideoRAM set too low?
> (EE) intel(0): Failed to allocate framebuffer. Is your VideoRAM set too low?
> (EE) intel(0): Failed to allocate framebuffer. Is your VideoRAM set too low?
> (EE) intel(0): Failed to allocate framebuffer. Is your VideoRAM set too low?
> (EE) intel(0): Failed to allocate framebuffer. Is your VideoRAM set too low?
> (EE) intel(0): Couldn't allocate video memory
> 
> Fatal server error:
> AddScreen/ScreenInit failed for driver 0
> 
> X connection to :0.0 broken (explicit kill or server shutdown).
> 
> # ls -l /dev/agpgart
> ls: /dev/agpgart: No such file or directory
> 
> Thanks in advance.
> 
> 
> ----------------------------------------------------------------------
> Gra - zostan agentem ABW!
> Zobacz >>> http://link.interia.pl/f1ba5
> 
> _______________________________________________
> freebsd-x11 at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-x11
> To unsubscribe, send any mail to "freebsd-x11-unsubscribe at freebsd.org"

More information about the freebsd-x11 mailing list