FreeBSD 7.0 -CURRENT unsupported Nvidia 8800
Sam Fourman Jr.
sfourman at gmail.com
Wed Sep 5 22:14:48 PDT 2007
hello,
I am wondering if someone can help me out, I just put built a new computer
I used a Nvidia 8800 GTS 320mb
it would seem that xorg 7.2 will not support this card
below is a dmesg and the xorg output is at the bottom
# dmesg
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-CURRENT #0: Wed Sep 5 11:12:34 CDT 2007
root@:/usr/obj/usr/src/sys/SAM
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Quad CPU @ 2.40GHz (2399.99-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6f7 Stepping = 7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Cores per package: 4
real memory = 3488546816 (3326 MB)
avail memory = 3409358848 (3251 MB)
ACPI APIC Table: <Nvidia ASUSACPI>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
ioapic0: Changing APIC ID to 4
ioapic0 <Version 1.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <Nvidia ASUSACPI> on motherboard
acpi0: [ITHREAD]
acpi_hpet0: <High Precision Event Timer> iomem 0xfeff0000-0xfeff03ff on acpi0
Timecounter "HPET" frequency 25000000 Hz quality 900
acpi0: Power Button (fixed)
acpi0: reservation of feff0000, 400 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cfdf0000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 928092806000928
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 928092806000928
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
cpu2: <ACPI CPU> on acpi0
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 928092806000928
device_attach: est2 attach returned 6
p4tcc2: <CPU Frequency Thermal Control> on cpu2
cpu3: <ACPI CPU> on acpi0
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 928092806000928
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
pci0: <memory, RAM> at device 0.4 (no driver attached)
pci0: <memory, RAM> at device 0.5 (no driver attached)
pci0: <memory, RAM> at device 0.6 (no driver attached)
pci0: <memory, RAM> at device 0.7 (no driver attached)
pci0: <memory, RAM> at device 1.0 (no driver attached)
pci0: <memory, RAM> at device 1.1 (no driver attached)
pci0: <memory, RAM> at device 1.2 (no driver attached)
pci0: <memory, RAM> at device 1.3 (no driver attached)
pci0: <memory, RAM> at device 1.4 (no driver attached)
pci0: <memory, RAM> at device 1.5 (no driver attached)
pci0: <memory, RAM> at device 1.6 (no driver attached)
pci0: <memory, RAM> at device 2.0 (no driver attached)
pci0: <memory, RAM> at device 2.1 (no driver attached)
pci0: <memory, RAM> at device 2.2 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xdf00-0xdf7f mem
0xec000000-0xecffffff,0xd0000000-0xdfffffff,0xea000000-0xebffffff irq
16 at device 0.0 on pci1
pcib2: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 7.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pci0: <memory, RAM> at device 9.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 10.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 10.1 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xeffff000-0xefffffff irq
21 at device 11.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 10 ports with 10 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xefffe000-0xefffe0ff
irq 22 at device 11.1 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb1: EHCI version 1.0
usb1: companion controller, 10 ports each: usb0
usb1: <EHCI (generic) USB 2.0 controller> on ehci0
usb1: USB revision 2.0
uhub1: <nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb1
uhub1: 10 ports with 10 removable, self powered
atapci0: <nVidia nForce MCP55 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 13.0 on
pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
atapci1: <nVidia nForce MCP55 SATA300 controller> port
0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xf700-0xf70f mem
0xefffd000-0xefffdfff irq 23 at device 14.0 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
atapci2: <nVidia nForce MCP55 SATA300 controller> port
0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xf200-0xf20f mem
0xefffc000-0xefffcfff irq 20 at device 14.1 on pci0
atapci2: [ITHREAD]
ata4: <ATA channel 0> on atapci2
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci2
ata5: [ITHREAD]
atapci3: <nVidia nForce MCP55 SATA300 controller> port
0xf100-0xf107,0xf000-0xf003,0xef00-0xef07,0xee00-0xee03,0xed00-0xed0f
mem 0xefffb000-0xefffbfff irq 21 at device 14.2 on pci0
atapci3: [ITHREAD]
ata6: <ATA channel 0> on atapci3
ata6: [ITHREAD]
ata7: <ATA channel 1> on atapci3
ata7: [ITHREAD]
pcib4: <ACPI PCI-PCI bridge> at device 15.0 on pci0
pci4: <ACPI PCI bus> on pcib4
ral0: <Ralink Technology RT2661> mem 0xefbf0000-0xefbf7fff irq 17 at
device 7.0 on pci4
ral0: MAC/BBP RT2661D, RF RT2529 (MIMO XR)
ral0: Ethernet address: 00:0e:2e:99:e4:dc
ral0: [ITHREAD]
fwohci0: <VIA Fire II (VT6306)> port 0xcf00-0xcf7f mem
0xefbff000-0xefbff7ff irq 19 at device 11.0 on pci4
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:11:d8:00:01:36:b0:9c
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x1508000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:11:d8:36:b0:9c
fwe0: Ethernet address: 02:11:d8:36:b0:9c
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:11:d8:00:01:36:b0:9c @ 0xfffe00000000,
S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
pci0: <multimedia> at device 15.1 (no driver attached)
nfe0: <NVIDIA nForce MCP55 Networking Adapter> port 0xec00-0xec07 mem
0xefffa000-0xefffafff,0xefff9000-0xefff90ff,0xefff8000-0xefff800f irq
23 at device 17.0 on pci0
miibus0: <MII bus> on nfe0
e1000phy0: <Marvell 88E1116 Gigabit PHY> PHY 1 on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
nfe0: Ethernet address: 00:1a:92:c0:d4:b2
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe0: [FILTER]
nfe1: <NVIDIA nForce MCP55 Networking Adapter> port 0xeb00-0xeb07 mem
0xefff7000-0xefff7fff,0xefff6000-0xefff60ff,0xefff5000-0xefff500f irq
20 at device 18.0 on pci0
miibus1: <MII bus> on nfe1
e1000phy1: <Marvell 88E1116 Gigabit PHY> PHY 1 on miibus1
e1000phy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
nfe1: Ethernet address: 00:1a:92:c0:df:70
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
nfe1: [FILTER]
pcib5: <ACPI PCI-PCI bridge> at device 22.0 on pci0
pci5: <ACPI PCI bus> on pcib5
atapci4: <SiI 3132 SATA300 controller> port 0x9f00-0x9f7f mem
0xef8ff000-0xef8ff07f,0xef8f8000-0xef8fbfff irq 16 at device 0.0 on
pci5
atapci4: [ITHREAD]
ata8: <ATA channel 0> on atapci4
ata8: [ITHREAD]
ata9: <ATA channel 1> on atapci4
ata9: [ITHREAD]
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xd0000-0xd3fff pnpid ORM0000 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ukbd0: <Logitech USB Receiver, class 0/0, rev 1.10/21.00, addr 2> on uhub0
kbd2 at ukbd0
ums0: <Logitech USB Receiver, class 0/0, rev 1.10/21.00, addr 2> on uhub0
ums0: 16 buttons and Z dir.
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad4: 152627MB <Seagate ST3160815AS 3.AAC> at ata2-master SATA300
ad6: 152627MB <Seagate ST3160815AS 3.AAC> at ata3-master SATA300
acd0: DVDR <SONY DVD RW AW-G170S/1.72> at ata6-master SATA150
acd1: DVDR <SONY DVD RW AW-G170S/1.72> at ata7-master SATA150
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
Trying to mount root from ufs:/dev/ad4s1a
nfe0: link state changed to DOWN
nfe0: link state changed to UP
here is what happens when using a xorg.conf file generated by nvidia-xconfig
# startx
xee1651139344c0d582393ac4d9affc53: not found
xauth: creating new authority file /root/.serverauth.1987
xauth: (stdin):1: bad display name ":0" in "add" command
xauth: creating new authority file /root/.Xauthority
xauth: (argv):1: bad display name ":0" in "list" command
xauth: creating new authority file /root/.Xauthority
xauth: (stdin):1: bad display name ":0" in "add" command
xauth: creating new authority file /root/.Xauthority
xauth: (argv):1: bad display name ":0" in "list" command
xauth: creating new authority file /root/.Xauthority
xauth: (stdin):1: bad display name ":0" in "add" command
X Window System Version 7.2.0
Release Date: 22 January 2007
X Protocol Version 11, Revision 0, Release 7.2
Build Operating System: FreeBSD 7.0-20070903-SNAP i386
Current Operating System: FreeBSD 7.0-CURRENT FreeBSD 7.0-CURRENT #0:
Wed Sep 5 11:12:34 CDT 2007 root@:/usr/obj/usr/src/sys/SAM i386
Build Date: 05 September 2007
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Sep 6 12:21:50 2007
(==) Using config file: "/etc/X11/xorg.conf"
NVIDIA: could not open the device file /dev/nvidiactl (No such file or
directory).
(EE) NVIDIA(0): Failed to initialize the NVIDIA kernel module! Please ensure
(EE) NVIDIA(0): that there is a supported NVIDIA GPU in this system, and
(EE) NVIDIA(0): that the NVIDIA device files have been created properly.
(EE) NVIDIA(0): Please consult the NVIDIA README for details.
(EE) NVIDIA(0): *** Aborting ***
(EE) Screen(s) found, but none have a usable configuration.
Fatal server error:
no screens found
XIO: fatal IO error 53 (Software caused connection abort) on X server ":0.0"
after 0 requests (0 known processed) with 0 events remaining.
xauth: creating new authority file /root/.Xauthority
xauth: (argv):1: bad display name ":0" in "remove" command
xauth: (argv):1: bad display name ":0" in "remove" command
#
Thank you for any Help
Sam Fourman Jr.
More information about the freebsd-x11
mailing list