Can anybody change the resolution to 1280x800?

Janvier Pang janvier.roc at gmail.com
Tue Dec 26 11:01:23 PST 2006


Thanks for your kindly reply.

I tried your options, I found that my card can not apply the "radeon" or
"ati" driver. If I use one of them , the X could not to be started, it said:


(EE) No devices detected.

I read the manual, my card is not in the list of radeon or ati driver.

Any ideas about change my resolutions to 1280x800? I tried several days, but
i still can not change it. (I can change my resolutions to 800x600 or
640x480, but not 1280x800)

B.Regs.

Janvier Pang


On 12/27/06, Abdullah Al-Marrie <almarrie at gmail.com> wrote:
>
> On 12/26/06, Janvier Pang <janvier.roc at gmail.com> wrote:
> > Dear All,
> >
> > I have a laptop, there're ATI Mobility Radeon X1300 display card and
> wide
> > screen with 1280x800 resolutions on it.
> >
> > I'd like to use the native ati driver, Unfortunately I can't find any
> > available driver about this card on the internet. So that I  must choose
> > another way to use this card.
> >
> > I configured the vesa driver in /etc/X11/xorg.conf, and then start the
> X. I
> > got the following message in /var/log/Xorg.0.log:
> >
> > ...
> > (II) VESA(0): First detailed timing is preferred mode
> > (II) VESA(0): redX: 0.575 redY: 0.359   greenX: 0.319 greenY: 0.532
> > (II) VESA(0): blueX: 0.155 blueY: 0.129   whiteX: 0.312 whiteY: 0.328
> > (II) VESA(0): Manufacturer's mask: 0
> > (II) VESA(0): Supported additional Video Mode:
> > (II) VESA(0): clock: 68.9 MHz   Image Size:  331 x 207 mm
> > (II) VESA(0): h_active: 1280  h_sync: 1301  h_sync_end 1333 h_blank_end
> 1408
> > h_border: 0
> > (II) VESA(0): v_active: 800  v_sync: 804  v_sync_end 808 v_blanking: 816
> > v_border: 0
> > (II) VESA(0):  QUANTADISPLAY
> > (II) VESA(0):  QD15TL072
> > (II) VESA(0): Searching for matching VESA mode(s):
> > (==) VESA(0): Write-combining range (0x0,0x1000) was already clear
> > ...
> >
> > After reading the manual, I add the "ModeLine" line in the
> > /etc/X11/xorg.conf to use the additional video mode:
> >
> > ...
> > Section "Monitor"
> >     Identifier  "My Monitor"
> >     HorizSync   31.5 - 64.3
> >     VertRefresh 50-70
> >     ModeLine "1280x800" 68.9 1280 1301 1333 1408 800 804 808 816
> > End Section
> > ...
> >
> > and change "Monitor" section as following:
> >
> > ...
> > Section "Screen"
> >     Identifier  "Screen 1"
> >     Device      "* Generic VESA compatible"
> >     Monitor     "My Monitor"
> >     DefaultDepth 24
> >
> >     Subsection "Display"
> >         Depth       24
> >         Modes       "1280x800"
> >         ViewPort    0 0
> >     EndSubsection
> > EndSection
> > ...
> >
> > OK, restart the X.
> >
> > The X was started, but the resolution is still 1024x768.
> >
> > I checked /var/log/Xorg.0.log carefully, and then I found the following
> > message in the log file:
> >
> > ...
> > (II) VESA(0): Total Memory: 256 64KB banks (16384kB)
> > (WW) VESA(0): config file hsync range 31.5-64.3kHz not within DDC hsync
> > ranges.
> > (WW) VESA(0): config file vrefresh range 50-70Hz not within DDC vrefresh
> > ranges.
> > (II) VESA(0): My Monitor: Using hsync range of 31.50-64.30 kHz
> > (II) VESA(0): My Monitor: Using vrefresh range of 50.00-70.00 Hz
> > (II) VESA(0): Not using mode "1280x800" (no mode of this name)
> > (--) VESA(0): Virtual size is 1024x768 (pitch 1024)
> > (**) VESA(0):  Built-in mode "1024x768"
> > (**) VESA(0):  Built-in mode "1024x768"
> > (**) VESA(0):  Built-in mode "800x600"
> > ...
> >
> > It said "1280x800" mode cound not to be found, but I have added this
> mode
> > into /etc/X11/xorg.conf. Why it can not to be detected?
> >
> > If I can use the additional video mode, I can use my wide screen under
> > 1280x800 resolution I think. Could anybody give me some hints about how
> to
> > apply the additional video mode?
> >
> > Thanks.
> >
> > Janvier Pang.
>
> Here is my xorg.conf file and I use ATI Radeon 1100
>
> I'm loading the dri module which is Xorg module to support radeon
>
> Section "Module"
>         Load  "dri"
>         Load  "glx"
>         Load  "freetype"
>         Load  "type1"
> EndSection
>
>
> Section "Monitor"
>         #DisplaySize      330   210     # mm
>         Identifier   "Monitor0"
>         VendorName   "SEC"
>         ModelName    "3845"
>         option       "DPMS"
> EndSection
>
>         Identifier  "Card0"
>         Driver      "radeon"
>         VideoRam    131072
>         VendorName  "ATI Technologies Inc"
>         BoardName   "RS482 [Radeon Xpress 200M]"
>         BusID       "PCI:1:5:0"
>
> Section "Screen"
>         Identifier      "Screen0"
>         Device          "Card0"
>         Monitor         "Monitor0"
>         DefaultDepth     24
>         SubSection "Display"
>                 Viewport 0 0
>                 Depth    24
>                 Modes    "1280x800" "1024x768" "800x600"
>         EndSubSection
> EndSection
>
>
> I'm able to use 1280x800
>
> PS: Xorg 7.2 may has a driver for your ATI video card, I hope it will
> be released soon.
>
>
> --
> Regards,
>
> -Abdullah Ibn Hamad Al-Marri
> Arab Portal
> http://www.WeArab.Net/
>


More information about the freebsd-x11 mailing list