Intel Centrino wireless-n 2230

[Kostya Berger]

It only keeps repeating this:<3>CTRL-EVENT-SCAN-RESULTS 
<3>WPS-AP-AVAILABLE-PIN 
<3>CTRL-EVENT-SCAN-RESULTS 
<3>WPS-AP-AVAILABLE-PIN .......
when I ask for 'status' it says:wpa_state=SCANNING
address=60:6c:66:4d:28:a3
 With kindest regards,
Kostya Berger
 
 

     On Sunday, 25 January 2015, 19:46, Adrian Chadd <adrian at freebsd.org> wrote:
   
 

 Ok, need to see if it's trying to associate>

in wpa_cli, do:

log_level debug

Or, run it like this

wpa_supplicant -i wlan0 -d -d -d -v -c /etc/wpa_supplicant.conf

(making sure no other supplicant is running)


-a


On 25 January 2015 at 09:16, Kostya Berger <bergerkos at yahoo.co.uk> wrote:
> Hi Adrian,
>
> no, it shows only iwn0 as "associated". Here is `ifconfig wlan0` output:
>
> wlan0: flags=8c43<UP,BROADCAST,RUNNING,OACTIVE,SIMPLEX,MULTICAST> metric 0
> mtu 1500
>    ether 60:6c:66:4d:28:a3
>    inet6 fe80::626c:66ff:fe4d:28a3%wlan0 prefixlen 64 scopeid 0x5
>    nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
>    media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
>    status: no carrier
>    ssid "" channel 12 (2467 MHz 11g)
>    country US authmode WPA1+WPA2/802.11i privacy MIXED deftxkey UNDEF
>    txpower 15 bmiss 10 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250
>    roam:rssi 7 roam:rate 5 protmode CTS wme roaming MANUAL bintval 0
>
>
> With kindest regards,
> Kostya Berger
>
>
>
> On Sunday, 25 January 2015, 18:44, Adrian Chadd <adrian at freebsd.org> wrote:
>
>
>
> Hi,
>
> Does ifconfig wlan0 list it as associated?
>
>
>
> -a
>
>
> On 24 January 2015 at 19:07, Kostya Berger <bergerkos at yahoo.co.uk> wrote:
>> Here's my ifconfig output:
>> wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
>> 1500
>>    ether 60:6c:66:4d:28:a3
>>    inet6 fe80::626c:66ff:fe4d:28a3%wlan0 prefixlen 64 scopeid 0x5
>>    nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
>>    media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
>>    status: no carrier
>>    ssid "" channel 12 (2467 MHz 11g)
>>    country US authmode WPA1+WPA2/802.11i privacy MIXED deftxkey UNDEF
>>    txpower 15 bmiss 10 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250
>>    roam:rssi 7 roam:rate 5 protmode CTS wme roaming MANUAL bintval 0
>>
>> So dhclient starts with the words "no link" and soon gives up. At that,
>> ifconfig wlan0 list scan returnes full list of available WiFi networks.Here
>> is my wpa_supplicant.conf (pretty generic):
>> ctrl_interface=/var/run/wpa_supplicant
>> ctrl_interface_group=wheel
>>
>> network={
>>    ssid="MyHOME-NET"
>>    scan_ssid=1
>>    key_mgmt=WPA-PSK
>>    psk="my passphrase"
>> }
>>
>> and here my /var/log/messages part to the point (not much):
>> Jan 25 05:49:45 kostya-home kernel: wlan0:
>> Jan 25 05:49:45 kostya-home kernel: Ethernet address: 60:6c:66:4d:28:a3
>> Jan 25 05:49:45 kostya-home devd: Executing '/etc/pccard_ether wlan0
>> start'
>> Jan 25 05:49:45 kostya-home wpa_supplicant[83148]: Successfully
>> initialized wpa_supplicant
>> Jan 25 05:49:45 kostya-home kernel: iwn0: iwn_read_firmware: ucode
>> rev=0x12a80601
>> Jan 25 05:49:56 kostya-home root: /etc/rc.d/dhclient: WARNING: failed to
>> start dhclient With kindest regards,
>> Kostya Berger
>>
>>
>>
>>      On Saturday, 24 January 2015, 1:51, Kostya Berger
>> <bergerkos at yahoo.co.uk> wrote:
>>
>>
>>
>>  Hello everyone,
>> glad to meet you. I subscribed to this list in order to get my above
>> mentioned card to work.Currently, the situation is as follows:It's Intel
>> Centrino wireless-N 2230 Mini PCIe that came pre-installed on my
>> GA-Z77N-wifi motherboard.I'm running 11.0-CURRENT, downloaded pre-compiled
>> txz distro files, dated 22.01.2015.
>> iwn0 interface gets created (in 10.1-RELEASE it doesn't), also wlan0
>> interface gets created all right.ifconfig wlan0 list scan command returns
>> the list of the available SSIDs with parameters.However, wpa_supplicant
>> fails to connect to my router's SSID, though it is present among the scan
>> results.ifconfig wlan0 shows, among other things, "no carrier" for wlan0.
>> Manual connection using wpa_cli is no better.
>> BTW, can I somehow apply the needed code to 10.1-STABLE source tree and
>> compile there, or do I need 11-CURRENT to run the latest version of this
>> driver? Because 11-CURRENT will require rebuilding all ports. So right now
>> I'm running it on a separate spare HDD, only base system.
>> Thanks to everyone for your hard work :)))
>>  With kindest regards,
>> Kostya Berger
>
>>
>>
>>
>>
>>
>> _______________________________________________
>> freebsd-wireless at freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-wireless
>> To unsubscribe, send any mail to "freebsd-wireless-unsubscribe at freebsd.org
> "
>
>