Broadcom BCM4318

[Mohammad BadieZadegan]

Yes, When I run this daemon for my SSID:

Successfully initialized wpa_supplicant
wlan0: Trying to associate with 14:cc:20:79:0c:35 (SSID='Saman 4' freq=2462
MHz)
wlan0: Authentication with 14:cc:20:79:0c:35 timed out.
wlan0: CTRL-EVENT-DISCONNECTED bssid=14:cc:20:79:0c:35 reason=3
locally_generated=1
wlan0: Trying to associate with 14:cc:20:79:0c:35 (SSID='Saman 4' freq=2462
MHz)
wlan0: Authentication with 14:cc:20:79:0c:35 timed out.
wlan0: CTRL-EVENT-DISCONNECTED bssid=14:cc:20:79:0c:35 reason=3
locally_generated=1
wlan0: Trying to associate with 14:cc:20:79:0c:35 (SSID='Saman 4' freq=2462
MHz)
^Cwlan0: CTRL-EVENT-DISCONNECTED bssid=14:cc:20:79:0c:35 reason=3
locally_generated=1
ioctl[SIOCS80211, op=26, val=0, arg_len=0]: Operation not supported
wlan0: CTRL-EVENT-TERMINATING

On Mon, Apr 20, 2015 at 12:12 PM, Matthias Apitz <guru at unixarea.de> wrote:

> El día Monday, April 20, 2015 a las 12:04:43PM +0430, Mohammad
> BadieZadegan escribió:
>
> > Dear Felix Friedlander,
> > Thanks for following my issue.
> > I copied and reinstall your new bwn-kmod-firmware (0.2.0).
> > I think that my state is better than but still I do not get any IP.
> > PS: My WiFi LED turned on but it has not get any IP address.
> >
> > ************** My dmesg ***********
> > siba_bwn0: <Broadcom BCM4318 802.11b/g Wireless> mem
> 0xd0204000-0xd0205fff
> > irq 20 at device 2.0 on pci5
> > bwn0 on siba_bwn0
> > bwn0: WLAN (chipid 0x4318 rev 9) PHY (analog 3 type 2 rev 7) RADIO (manuf
> > 0x17f ver 0x2050 rev 8)
> > bwn0: DMA (32 bits)
> > bwn0: firmware version (rev 666 patch 2 date 0xb217 time 0x9e7)
> > bwn0: warn: firmware state (0)
> > bwn0: warn: firmware state (0)
> > bwn0: warn: firmware state (0)
> > bwn0: warn: firmware state (0)
> >
> > ************** My ifconfig ************
> > bwn0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
> 2290
> >     ether 00:14:a5:63:39:e5
> >     nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
> >     media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
> >     status: associated
> > wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
> 1500
> >     ether 00:14:a5:63:39:e5
> >     nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
> >     media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
> >     status: no carrier
> >     ssid "" channel 4 (2427 MHz 11g)
> >     country US authmode WPA2/802.11i privacy ON deftxkey UNDEF txpower 30
> >     bmiss 7 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi
> 7
> >     roam:rate 5 protmode CTS wme roaming MANUAL
> > **********************************************
>
> The interface wlan0 is not associated with any AP (and so it can not get
> any IP addr). Do you run wpa_supplicant(8) daemon with a correct
> configuration matching your air radio APs?
>
> Btw: Please, do not top post and trim your replies.
>
>         matthias
>
>
> --
> Matthias Apitz, guru at unixarea.de, http://www.unixarea.de/
> +49-170-4527211    +49-176-38902045
> "Wenn der Mensch von den Umständen gebildet wird, so muß man die Umstände
> menschlich bilden."
> "Si el hombre es formado por las circunstancias entonces es necesario
> formar humanamente
> las circunstancias", Karl Marx in Die heilige Familie / La sagrada familia
> (MEW 2, 138)
>



-- 
<http://ir.linkedin.com/in/xadegan>