bhyve pci passthrough usb controller
Wouter Snels
nospam at ofloo.net
Fri Mar 23 18:54:41 UTC 2018
No the xhci driver is not attached only the the ppt driver is, but
that's normal because you set pptdevs="0/20/0 4/0/0" in /boot/loader.conf
Op 23-03-18 om 18:25 schreef Julian Elischer:
> On 23/3/18 11:40 pm, Wouter Snels wrote:
>
>
> new wrapping is no better
> It looks like the device you are passing though is not removed from
> freebsd first.
> but it's hard to tell.
>
>> |Hi, .. I'm trying to pci passhthrough a usb controller to a bhyve
>> windows 7 virtualization. When I start the virtual machine it freezes
>> the entire system and this shows up on the console. To be clear the
>> system runs without any problems without the pci passthrough. |
>> ||(ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 08 e0 ff 40 40 29 00
>> 00 00 00 00 (ada0:ahcich0:0:0:0): CAM status: CCB request was invalid
>> (ada0:ahcich0:0:0:0): Error 22, Unretryable error
>> (aprobe0:ahcich0:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00
>> 00 00 00 (aprobe0:ahcich0:0:0:0): CAM status: CCB request was invalid
>> (aprobe0:ahcich0:0:0:0): Error 22, Unretryable error ada0 at ahcich0 bus
>> 0 scbus0 target 0 lun 0 ada0: <ST500DM002-1SB10A CC43> s/n ZA4292G6
>> detached (aprobe0:ahcich0:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40
>> 00 00 00 00 00 00 (aprobe0:ahcich0:0:0:0): CAM status: CCB request was
>> invalid (aprobe0:ahcich0:0:0:0): Error 22, Unretryable error ahcich0:
>> Poll timeout on slot 28 port 0 ahcich0: is 20000000 cs 10000000 ss
>> 00000000 rs 10000000 tfd 1d0 serr 00000800 cmd 00005c17
>> (aprobe0:ahcich0:0:0:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00
>> 00 00 (aprobe0:ahcich0:0:0:0): CAM status: Command timeout
>> (aprobe0:ahcich0:0:0:0): Error 5, Retries exhausted
>> (ada0:ahcich0:0:0:0): SETFEATURES ENABLE RCACHE. ACB: ef aa 00 00 00 40
>> 00 00 00 00 00 00 (ada0:ahcich0:0:0:0): CAM status: CCB request was
>> invalid (ada0:ahcich0:0:0:0): Error 22, Unretryable error ahcich0: Poll
>> timeout on slot 30 port 0 ahcich0: is 20000000 cs 40000000 ss 00000000
>> rs 40000000 tfd 1d0 serr 00000800 cmd 00005e17 (aprobe0:ahcich0:0:0:0):
>> SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
>> (aprobe0:ahcich0:0:0:0): CAM status: Command timeout
>> (aprobe0:ahcich0:0:0:0): Error 5, Retries exhausted
>> (ada0:ahcich0:0:0:0): SETFEATURES ENABLE WCACHE. ACB: ef 02 00 00 00 40
>> 00 00 00 00 00 00 (ada0:ahcich0:0:0:0): CAM status: CCB request was
>> invalid (ada0:ahcich0:0:0:0): Error 22, Unretryable error
>> (ada0:ahcich0:0:0:0): Periph destroyed em0: Watchdog timeout Queue[0]--
>> resetting Interface is RUNNING and ACTIVE em0: TX Queue 0 ------ em0: hw
>> tdh = 428, hw tdt = 471 em0: Tx Queue Status = -2147483648 em0: TX
>> descriptors avail = 981 em0: Tx Descriptors avail failure = 0 em0: RX
>> Queue 0 ------ em0: hw rdh = 912, hw rdt = 908 em0: RX discarded packets
>> = 0 em0: RX Next to Check = 909 em0: RX Next to Refresh = 908 xl0:
>> watchdog timeout em0: Watchdog timeout Queue[0]-- resetting Interface is
>> RUNNING and ACTIVE em0: TX Queue 0 ------ em0: hw tdh = 0, hw tdt = 58
>> em0: Tx Queue Status = -2147483648 em0: TX descriptors avail = 966 em0:
>> Tx Descriptors avail failure = 0 em0: RX Queue 0 ------ em0: hw rdh = 0,
>> hw rdt = 1023 em0: RX discarded packets = 0 em0: RX Next to Check = 0
>> em0: RX Next to Refresh = 1023 em0: Watchdog timeout Queue[0]--
>> resetting Interface is RUNNING and ACTIVE em0: TX Queue 0 ------ em0: hw
>> tdh = 0, hw tdt = 58 em0: Tx Queue Status = -2147483648 em0: TX
>> descriptors avail = 966 em0: Tx Descriptors avail failure = 0 em0: RX
>> Queue 0 ------ em0: hw rdh = 0, hw rdt = 1023 em0: RX discarded packets
>> = 0 em0: RX Next to Check = 0 em0: RX Next to Refresh = 1023 xl0:
>> watchdog timeout em0: Watchdog timeout Queue[0]-- resetting Interface is
>> RUNNING and ACTIVE em0: TX Queue 0 ------ em0: hw tdh = 0, hw tdt = 54
>> em0: Tx Queue Status = -2147483648 em0: TX descriptors avail = 970 em0:
>> Tx Descriptors avail failure = 0 em0: RX Queue 0 ------ em0: hw rdh = 0,
>> hw rdt = 1023 em0: RX discarded packets = 0include GENERIC ident OFL
>> options IPFIREWALL||||||
>>
>> |Hi, .. I'm trying to pci passhthrough a usb controller to a bhyve
>> windows 7 virtualization. When I start the virtual machine it freezes
>> the entire system and this shows up on the console. To be clear the
>> system runs without any problems without the pci passthrough. |
>> ||(ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 08 e0 ff 40 40 29 00
>> 00 00 00 00 (ada0:ahcich0:0:0:0): CAM status: CCB request was invalid
>> (ada0:ahcich0:0:0:0): Error 22, Unretryable error
>> (aprobe0:ahcich0:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00
>> 00 00 00 (aprobe0:ahcich0:0:0:0): CAM status: CCB request was invalid
>> (aprobe0:ahcich0:0:0:0): Error 22, Unretryable error ada0 at ahcich0 bus
>> 0 scbus0 target 0 lun 0 ada0: <ST500DM002-1SB10A CC43> s/n ZA4292G6
>> detached (aprobe0:ahcich0:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40
>> 00 00 00 00 00 00 (aprobe0:ahcich0:0:0:0): CAM status: CCB request was
>> invalid (aprobe0:ahcich0:0:0:0): Error 22, Unretryable error ahcich0:
>> Poll timeout on slot 28 port 0 ahcich0: is 20000000 cs 10000000 ss
>> 00000000 rs 10000000 tfd 1d0 serr 00000800 cmd 00005c17
>> (aprobe0:ahcich0:0:0:0): SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00
>> 00 00 (aprobe0:ahcich0:0:0:0): CAM status: Command timeout
>> (aprobe0:ahcich0:0:0:0): Error 5, Retries exhausted
>> (ada0:ahcich0:0:0:0): SETFEATURES ENABLE RCACHE. ACB: ef aa 00 00 00 40
>> 00 00 00 00 00 00 (ada0:ahcich0:0:0:0): CAM status: CCB request was
>> invalid (ada0:ahcich0:0:0:0): Error 22, Unretryable error ahcich0: Poll
>> timeout on slot 30 port 0 ahcich0: is 20000000 cs 40000000 ss 00000000
>> rs 40000000 tfd 1d0 serr 00000800 cmd 00005e17 (aprobe0:ahcich0:0:0:0):
>> SOFT_RESET. ACB: 00 00 00 00 00 00 00 00 00 00 00 00
>> (aprobe0:ahcich0:0:0:0): CAM status: Command timeout
>> (aprobe0:ahcich0:0:0:0): Error 5, Retries exhausted
>> (ada0:ahcich0:0:0:0): SETFEATURES ENABLE WCACHE. ACB: ef 02 00 00 00 40
>> 00 00 00 00 00 00 (ada0:ahcich0:0:0:0): CAM status: CCB request was
>> invalid (ada0:ahcich0:0:0:0): Error 22, Unretryable error
>> (ada0:ahcich0:0:0:0): Periph destroyed em0: Watchdog timeout Queue[0]--
>> resetting Interface is RUNNING and ACTIVE em0: TX Queue 0 ------ em0: hw
>> tdh = 428, hw tdt = 471 em0: Tx Queue Status = -2147483648 em0: TX
>> descriptors avail = 981 em0: Tx Descriptors avail failure = 0 em0: RX
>> Queue 0 ------ em0: hw rdh = 912, hw rdt = 908 em0: RX discarded packets
>> = 0 em0: RX Next to Check = 909 em0: RX Next to Refresh = 908 xl0:
>> watchdog timeout em0: Watchdog timeout Queue[0]-- resetting Interface is
>> RUNNING and ACTIVE em0: TX Queue 0 ------ em0: hw tdh = 0, hw tdt = 58
>> em0: Tx Queue Status = -2147483648 em0: TX descriptors avail = 966 em0:
>> Tx Descriptors avail failure = 0 em0: RX Queue 0 ------ em0: hw rdh = 0,
>> hw rdt = 1023 em0: RX discarded packets = 0 em0: RX Next to Check = 0
>> em0: RX Next to Refresh = 1023 em0: Watchdog timeout Queue[0]--
>> resetting Interface is RUNNING and ACTIVE em0: TX Queue 0 ------ em0: hw
>> tdh = 0, hw tdt = 58 em0: Tx Queue Status = -2147483648 em0: TX
>> descriptors avail = 966 em0: Tx Descriptors avail failure = 0 em0: RX
>> Queue 0 ------ em0: hw rdh = 0, hw rdt = 1023 em0: RX discarded packets
>> = 0 em0: RX Next to Check = 0 em0: RX Next to Refresh = 1023 xl0:
>> watchdog timeout em0: Watchdog timeout Queue[0]-- resetting Interface is
>> RUNNING and ACTIVE em0: TX Queue 0 ------ em0: hw tdh = 0, hw tdt = 54
>> em0: Tx Queue Status = -2147483648 em0: TX descriptors avail = 970 em0:
>> Tx Descriptors avail failure = 0 em0: RX Queue 0 ------ em0: hw rdh = 0,
>> hw rdt = 1023 em0: RX discarded packets = 0include GENERIC ident OFL
>> options IPFIREWALL options IPFIREWALL_VERBOSE options
>> IPFIREWALL_DEFAULT_TO_ACCEPT options DUMMYNET options IPDIVERT options
>> CONSPEED=115200 em0: RX Next to Check = 0 em0: RX Next to Refresh =
>> 1023 ||||
>> |||I've recompiled the kernel without the xhci driver. I've tested both
>> usb controllers. Both "|||||Sunrise Point-H USB 3.0 xHCI
>> Controller|"||||| and "|||uPD720202 USB 3.0 Host Controller|", both
>> showed the same error on the console screen.| # uname FreeBSD
>> 11.1-STABLE #1 r331092M # custom kernel include GENERIC ident OFL
>> options IPFIREWALL options IPFIREWALL_VERBOSE options
>> IPFIREWALL_DEFAULT_TO_ACCEPT options DUMMYNET options IPDIVERT options
>> CONSPEED=115200 * note commented "device xhci" in generic # svn info
>> |||Path: . Working Copy Root Path: /usr/src URL:
>> https://svn0.eu.freebsd.org/base/stable/11 Relative URL: ^/stable/11
>> Repository Root: https://svn0.eu.freebsd.org/base Repository UUID:
>> ccf9f872-aa2e-dd11-9fc8-001c23d0bc1f Revision: 331092 Node Kind:
>> directory Schedule: normal Last Changed Author: eadler Last Changed Rev:
>> 331092 Last Changed Date: 2018-03-17 07:44:39 +0100 (Sat, 17 Mar 2018)
>> |# vm passthru DEVICE BHYVE ID READY DESCRIPTION hostb0 0/0/0 No Xeon
>> E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers
>> pcib1 0/1/0 No Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe
>> Controller (x16) vgapci0 0/2/0 No HD Graphics 530 |||ppt0| 0/20/0 Yes
>> Sunrise Point-H USB 3.0 xHCI Controller none0 0/20/2
>> No Sunrise Point-H Thermal subsystem none1 0/22/0 No Sunrise Point-H
>> CSME HECI ahci0 0/23/0 No Sunrise Point-H SATA controller [AHCI mode]
>> pcib2 0/28/0 No Sunrise Point-H PCI Express Root Port pcib4 0/28/6 No
>> Sunrise Point-H PCI Express Root Port isab0 0/31/0 No Sunrise Point-H
>> LPC Controller none2 0/31/2 No Sunrise Point-H PMC hdac0 0/31/3 No
>> Sunrise Point-H HD Audio none3 0/31/4 No Sunrise Point-H SMBus em0
>> 0/31/6 No Ethernet Connection (2) I219-V pcib3 2/0/0 No XIO2001 PCI
>> Express-to-PCI Bridge xl0 3/0/0 No 3c905B 100BaseTX [Cyclone] ppt1 4/0/0
>> Yes uPD720202 USB 3.0 Host Controller ||ppt1 at pci0:4:0:0:
>> class=0x0c0330 card=0x00151912 chip=0x00151912 rev=0x02
>> hdr=0x00 vendor = 'Renesas Technology Corp.' device = 'uPD720202 USB 3.0
>> Host Controller' class = serial bus subclass = USB
>> |||ppt|0 at pci0:0:20:0: class=0x0c0330 card=0x06ba1028 chip=0xa12f8086
>> rev=0x31 hdr=0x00 vendor = 'Intel Corporation' device = 'Sunrise Point-H
>> USB 3.0 xHCI Controller' class = serial bus subclass = USB # grep -i
>> pptdevfs loader.conf ||pptdevs="0/20/0 4/0/0" # vm configure
>> ||passthru0="0/20/0"|
>>
>> |# vm configure ||passthru0="4/0/0"|
>> ||Any suggestions on what I'm doing wrong?||
>> Regards, Ofloo
>> ||||||
>>
>> ||options IPFIREWALL_VERBOSE options IPFIREWALL_DEFAULT_TO_ACCEPT
>> options
>> DUMMYNET options IPDIVERT options CONSPEED=115200 em0: RX Next to Check
>> = 0 em0: RX Next to Refresh = 1023 ||||
>> |||I've recompiled the kernel without the xhci driver. I've tested both
>> usb controllers. Both "|||||Sunrise Point-H USB 3.0 xHCI
>> Controller|"||||| and "|||uPD720202 USB 3.0 Host Controller|", both
>> showed the same error on the console screen.| # uname FreeBSD
>> 11.1-STABLE #1 r331092M # custom kernel include GENERIC ident OFL
>> options IPFIREWALL options IPFIREWALL_VERBOSE options
>> IPFIREWALL_DEFAULT_TO_ACCEPT options DUMMYNET options IPDIVERT options
>> CONSPEED=115200 * note commented "device xhci" in generic # svn info
>> |||Path: . Working Copy Root Path: /usr/src URL:
>> https://svn0.eu.freebsd.org/base/stable/11 Relative URL: ^/stable/11
>> Repository Root: https://svn0.eu.freebsd.org/base Repository UUID:
>> ccf9f872-aa2e-dd11-9fc8-001c23d0bc1f Revision: 331092 Node Kind:
>> directory Schedule: normal Last Changed Author: eadler Last Changed Rev:
>> 331092 Last Changed Date: 2018-03-17 07:44:39 +0100 (Sat, 17 Mar 2018)
>> |# vm passthru DEVICE BHYVE ID READY DESCRIPTION hostb0 0/0/0 No Xeon
>> E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers
>> pcib1 0/1/0 No Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe
>> Controller (x16) vgapci0 0/2/0 No HD Graphics 530 |||ppt0| 0/20/0 Yes
>> Sunrise Point-H USB 3.0 xHCI Controller none0 0/20/2
>> No Sunrise Point-H Thermal subsystem none1 0/22/0 No Sunrise Point-H
>> CSME HECI ahci0 0/23/0 No Sunrise Point-H SATA controller [AHCI mode]
>> pcib2 0/28/0 No Sunrise Point-H PCI Express Root Port pcib4 0/28/6 No
>> Sunrise Point-H PCI Express Root Port isab0 0/31/0 No Sunrise Point-H
>> LPC Controller none2 0/31/2 No Sunrise Point-H PMC hdac0 0/31/3 No
>> Sunrise Point-H HD Audio none3 0/31/4 No Sunrise Point-H SMBus em0
>> 0/31/6 No Ethernet Connection (2) I219-V pcib3 2/0/0 No XIO2001 PCI
>> Express-to-PCI Bridge xl0 3/0/0 No 3c905B 100BaseTX [Cyclone] ppt1 4/0/0
>> Yes uPD720202 USB 3.0 Host Controller ||ppt1 at pci0:4:0:0:
>> class=0x0c0330 card=0x00151912 chip=0x00151912 rev=0x02
>> hdr=0x00 vendor = 'Renesas Technology Corp.' device = 'uPD720202 USB 3.0
>> Host Controller' class = serial bus subclass = USB
>> |||ppt|0 at pci0:0:20:0: class=0x0c0330 card=0x06ba1028 chip=0xa12f8086
>> rev=0x31 hdr=0x00 vendor = 'Intel Corporation' device = 'Sunrise Point-H
>> USB 3.0 xHCI Controller' class = serial bus subclass = USB # grep -i
>> pptdevfs loader.conf ||pptdevs="0/20/0 4/0/0" # vm configure
>> ||passthru0="0/20/0"|
>>
>> |# vm configure ||passthru0="4/0/0"|
>> ||Any suggestions on what I'm doing wrong?||
>>
>> edit: previous wrapping was all wrong.
>> Regards, Ofloo
>> ||||||
>>
>>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.freebsd.org/pipermail/freebsd-virtualization/attachments/20180323/fe7be2eb/attachment-0001.sig>
More information about the freebsd-virtualization
mailing list