kern/120034: 6.2 & 6.3 hangs on boot at usb0: OHCI with 1.5 G
memory, works with 512 M
Kenneth
kennethcf at earthlink.net
Sun Jan 27 11:30:02 PST 2008
The following reply was made to PR usb/120034; it has been noted by GNATS.
From: Kenneth <kennethcf at earthlink.net>
To: Remko Lodder <remko at FreeBSD.org>
Cc: freebsd-gnats-submit at FreeBSD.org
Subject: Re: kern/120034: 6.2 & 6.3 hangs on boot at usb0: OHCI with 1.5 G
memory, works with 512 M
Date: Sun, 27 Jan 2008 14:12:20 -0500 (GMT-05:00)
------------OIMQJV4d8WPYIxnea41D38
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 7bit
OK..more info.
Seems like disabling USB when 1.5G is plugged in works, but then I loose my working USB which I use for my working memory stick and floppy drive.
Enabling and disableing ACPI had no effect.
When I enable usb, dmesg is the same up to the point of hanging with the exception of the mem and iomem fields in the "atapci0" and "atapci1" lines. With 1.5G and usb enabled, my hung kernel says:
atapci0: ...mem 0x80207600 - 0x802077ff... the port locations are the same
atapci1: ...mem 0x80207400 - 0x802075ff... the port locations are the same
Attached are full dmesg outputs of configurations that work, i.e. no hang:
"dmesg_0.5G" - 0.5G memory, full usb, full ACPI (6.3 .iso kernel)
"dmesg_1.0G" - 1.0G memory, full usb, full ACPI (6.3 .iso kernel)
"dmesg_1.5G_nousb" - 1.5G memory, no usb, full ACPI (6.3 .iso kernel)
I also tried 6.2 .iso kernel from the install CD and it still hangs with 1.5G.
I do not know how I can provide you with a full dmesg when the system hangs. Can you tell me how I can log output of a boot sequence that hangs for later analysis? I have no shells in which to run dmesg. Extended logging does not help as I still do not know how to log it.
-----Original Message-----
>From: Remko Lodder <remko at FreeBSD.org>
>Sent: Jan 27, 2008 5:44 AM
>To: Kenneth Freidank <kennethcf at earthlink.net>
>Cc: freebsd-gnats-submit at FreeBSD.org
>Subject: Re: kern/120034: 6.2 & 6.3 hangs on boot at usb0: OHCI with 1.5 G memory, works with 512 M
>
>Kenneth Freidank wrote:
>
>Could you disable USB support in the bios and see where that leads
>up to? could it be that the additional memory kicks in the USB
>controller? and/or perhaps any other region?
>
>You did not provide a full boot dmesg btw; just giving parts of
>it makes it very hard to see what might be going on, in addition
>it could be interesting to start the freebsd installation without
>acpi support, and doing a boot verbose (that's 2 additional things
>we might like to see).
>
>Thanks,
>remko
>
>--
>/"\ Best regards, | remko at FreeBSD.org
>\ / Remko Lodder | remko at EFnet
> X http://www.evilcoder.org/ |
>/ \ ASCII Ribbon Campaign | Against HTML Mail and News
------------OIMQJV4d8WPYIxnea41D38
Content-Disposition: attachment; filename="dmesg_0.5G"
Content-Type: application/octet-stream; name=dmesg_0.5G
Content-Transfer-Encoding: 7bit
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.3-RELEASE #0: Wed Jan 16 04:45:45 UTC 2008
root at dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3000.12-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf4a Stepping = 10
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x649d<SSE3,RSVD2,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Logical CPUs per core: 2
real memory = 468365312 (446 MB)
avail memory = 444076032 (423 MB)
ACPI APIC Table: <INTEL D11020M >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 4
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Jan 16 2008 04:43:12)
acpi0: <INTEL D11020M> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21
acpi0: Power Button (fixed)
unknown: I/O range not supported
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_perf1: <ACPI CPU Frequency Control> on cpu1
acpi_perf1: failed in PERF_STATUS attach
device_attach: acpi_perf1 attach returned 6
acpi_perf1: <ACPI CPU Frequency Control> on cpu1
acpi_perf1: failed in PERF_STATUS attach
device_attach: acpi_perf1 attach returned 6
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xfff00000-0xffffffff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 5.0 (no driver attached)
atapci0: <ATI IXP400 SATA150 controller> port 0x3068-0x306f,0x3084-0x3087,0x3060-0x3067,0x3080-0x3083,0x3030-0x303f mem 0x30207600-0x302077ff irq 23 at device 17.0 on pci0
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
atapci1: <ATI IXP400 SATA150 controller> port 0x3058-0x305f,0x307c-0x307f,0x3050-0x3057,0x3078-0x307b,0x3020-0x302f mem 0x30207400-0x302075ff irq 22 at device 18.0 on pci0
ata4: <ATA channel 0> on atapci1
ata5: <ATA channel 1> on atapci1
ohci0: <ATI SB400 USB Controller> irq 19 at device 19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <ATI SB400 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1: <ATI SB400 USB Controller> irq 19 at device 19.1 on pci0
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: <ATI SB400 USB Controller> on ohci1
usb1: USB revision 1.0
uhub1: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
ehci0: <ATI SB400 USB 2.0 controller> irq 19 at device 19.2 on pci0
ehci0: [GIANT-LOCKED]
usb2: waiting for BIOS to give up control
usb2: timed out waiting for BIOS
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <ATI SB400 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci2: <ATI IXP400 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3000-0x300f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci2
ata1: <ATA channel 1> on atapci2
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci2: <ACPI PCI bus> on pcib2
rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem 0x30010000-0x300100ff irq 21 at device 2.0 on pci2
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:19:d1:16:5f:fb
pci2: <simple comms> at device 4.0 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 4 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
umass0: vendor 0x058f USB Reader, rev 1.10/1.00, addr 2
Timecounters tick every 1.000 msec
hptrr: no controller detected.
ad0: 157066MB <Hitachi HDS721616PLAT80 P22OA60A> at ata0-master UDMA133
ad1: 238475MB <WDC WD2500JB-00REA0 20.00K20> at ata0-slave UDMA100
acd0: DVDR <TSSTcorpCD/DVDW TS-H652D/GA01> at ata1-master UDMA33
SMP: AP CPU #1 Launched!
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Generic USB SD Reader 1.00> Removable Direct Access SCSI-0 device
da0: 1.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
da1 at umass-sim0 bus 0 target 0 lun 1
da1: <Generic USB CF Reader 1.01> Removable Direct Access SCSI-0 device
da1: 1.000MB/s transfers
da1: Attempt to query device size failed: NOT READY, Medium not present
da2 at umass-sim0 bus 0 target 0 lun 2
da2: <Generic USB SM Reader 1.02> Removable Direct Access SCSI-0 device
da2: 1.000MB/s transfers
da2: Attempt to query device size failed: NOT READY, Medium not present
da3 at umass-sim0 bus 0 target 0 lun 3
da3: <Generic USB MS Reader 1.03> Removable Direct Access SCSI-0 device
da3: 1.000MB/s transfers
da3: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/ad1s2a
------------OIMQJV4d8WPYIxnea41D38
Content-Disposition: attachment; filename="dmesg_1.0G"
Content-Type: application/octet-stream; name=dmesg_1.0G
Content-Transfer-Encoding: 7bit
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.3-RELEASE #0: Wed Jan 16 04:45:45 UTC 2008
root at dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3000.13-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf4a Stepping = 10
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x649d<SSE3,RSVD2,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Logical CPUs per core: 2
real memory = 938127360 (894 MB)
avail memory = 904040448 (862 MB)
ACPI APIC Table: <INTEL D11020M >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 4
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Jan 16 2008 04:43:12)
acpi0: <INTEL D11020M> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21
acpi0: Power Button (fixed)
unknown: I/O range not supported
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_perf1: <ACPI CPU Frequency Control> on cpu1
acpi_perf1: failed in PERF_STATUS attach
device_attach: acpi_perf1 attach returned 6
acpi_perf1: <ACPI CPU Frequency Control> on cpu1
acpi_perf1: failed in PERF_STATUS attach
device_attach: acpi_perf1 attach returned 6
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xfff00000-0xffffffff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 5.0 (no driver attached)
atapci0: <ATI IXP400 SATA150 controller> port 0x3068-0x306f,0x3084-0x3087,0x3060-0x3067,0x3080-0x3083,0x3030-0x303f mem 0x60207600-0x602077ff irq 23 at device 17.0 on pci0
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
atapci1: <ATI IXP400 SATA150 controller> port 0x3058-0x305f,0x307c-0x307f,0x3050-0x3057,0x3078-0x307b,0x3020-0x302f mem 0x60207400-0x602075ff irq 22 at device 18.0 on pci0
ata4: <ATA channel 0> on atapci1
ata5: <ATA channel 1> on atapci1
ohci0: <ATI SB400 USB Controller> irq 19 at device 19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <ATI SB400 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1: <ATI SB400 USB Controller> irq 19 at device 19.1 on pci0
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: <ATI SB400 USB Controller> on ohci1
usb1: USB revision 1.0
uhub1: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
ehci0: <ATI SB400 USB 2.0 controller> irq 19 at device 19.2 on pci0
ehci0: [GIANT-LOCKED]
usb2: waiting for BIOS to give up control
usb2: timed out waiting for BIOS
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <ATI SB400 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci2: <ATI IXP400 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3000-0x300f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci2
ata1: <ATA channel 1> on atapci2
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci2: <ACPI PCI bus> on pcib2
rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem 0x60010000-0x600100ff irq 21 at device 2.0 on pci2
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:19:d1:16:5f:fb
pci2: <simple comms> at device 4.0 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 4 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
umass0: vendor 0x058f USB Reader, rev 1.10/1.00, addr 2
Timecounters tick every 1.000 msec
hptrr: no controller detected.
ad0: 157066MB <Hitachi HDS721616PLAT80 P22OA60A> at ata0-master UDMA133
ad1: 238475MB <WDC WD2500JB-00REA0 20.00K20> at ata0-slave UDMA100
acd0: DVDR <TSSTcorpCD/DVDW TS-H652D/GA01> at ata1-master UDMA33
SMP: AP CPU #1 Launched!
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Generic USB SD Reader 1.00> Removable Direct Access SCSI-0 device
da0: 1.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
da1 at umass-sim0 bus 0 target 0 lun 1
da1: <Generic USB CF Reader 1.01> Removable Direct Access SCSI-0 device
da1: 1.000MB/s transfers
da1: Attempt to query device size failed: NOT READY, Medium not present
da2 at umass-sim0 bus 0 target 0 lun 2
da2: <Generic USB SM Reader 1.02> Removable Direct Access SCSI-0 device
da2: 1.000MB/s transfers
da2: Attempt to query device size failed: NOT READY, Medium not present
da3 at umass-sim0 bus 0 target 0 lun 3
da3: <Generic USB MS Reader 1.03> Removable Direct Access SCSI-0 device
da3: 1.000MB/s transfers
da3: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/ad1s2a
------------OIMQJV4d8WPYIxnea41D38
Content-Disposition: attachment; filename="dmesg_1.5G_nousb"
Content-Type: application/octet-stream; name=dmesg_1.5G_nousb
Content-Transfer-Encoding: 7bit
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.3-RELEASE #0: Wed Jan 16 04:45:45 UTC 2008
root at dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3000.13-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf4a Stepping = 10
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x649d<SSE3,RSVD2,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Logical CPUs per core: 2
real memory = 1474998272 (1406 MB)
avail memory = 1431105536 (1364 MB)
ACPI APIC Table: <INTEL D11020M >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 4
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Jan 16 2008 04:43:12)
acpi0: <INTEL D11020M> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21
acpi0: Power Button (fixed)
unknown: I/O range not supported
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_perf1: <ACPI CPU Frequency Control> on cpu1
acpi_perf1: failed in PERF_STATUS attach
device_attach: acpi_perf1 attach returned 6
acpi_perf1: <ACPI CPU Frequency Control> on cpu1
acpi_perf1: failed in PERF_STATUS attach
device_attach: acpi_perf1 attach returned 6
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xfff00000-0xffffffff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 5.0 (no driver attached)
atapci0: <ATI IXP400 SATA150 controller> port 0x3068-0x306f,0x3084-0x3087,0x3060-0x3067,0x3080-0x3083,0x3030-0x303f mem 0x80204600-0x802047ff irq 23 at device 17.0 on pci0
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
atapci1: <ATI IXP400 SATA150 controller> port 0x3058-0x305f,0x307c-0x307f,0x3050-0x3057,0x3078-0x307b,0x3020-0x302f mem 0x80204400-0x802045ff irq 22 at device 18.0 on pci0
ata4: <ATA channel 0> on atapci1
ata5: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci2: <ATI IXP400 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3000-0x300f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci2
ata1: <ATA channel 1> on atapci2
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci2: <ACPI PCI bus> on pcib2
rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem 0x80010000-0x800100ff irq 21 at device 2.0 on pci2
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:19:d1:16:5f:fb
pci2: <simple comms> at device 4.0 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 4 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
hptrr: no controller detected.
ad0: 157066MB <Hitachi HDS721616PLAT80 P22OA60A> at ata0-master UDMA133
ad1: 238475MB <WDC WD2500JB-00REA0 20.00K20> at ata0-slave UDMA100
acd0: DVDR <TSSTcorpCD/DVDW TS-H652D/GA01> at ata1-master UDMA33
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad1s2a
------------OIMQJV4d8WPYIxnea41D38--
More information about the freebsd-usb
mailing list