APU3 ethernet can't transmit

[Stefan Bethke]

I've tried one more time with this in rc.conf:

network_interfaces="igb0"
ifconfig_igb0="-lro -vlanhwtso -tso4 -vlanhwfilter -rxcsum -txcsum -vlanhwtag -vlanmtu -vlanhwcsum -tso6 -txcsum6"

Whick produces this: options=802020<JUMBO_MTU,WOL_MAGIC>

No joy. What's interesting is that the left LED on the plug in blinking with about 2Hz, so clearly the PHY or controller is unhappy about something. The i210 datasheet has a table with all modes the LEDs support, but it doesn't mention this fast blinking. The right LED is on constantly, which should indicate a link. This is the same on all three ports, irrespective of configuration.

I also just tried netbooting, and that doesn't seem to be working either. So I guess it's time to RMA it.

Stefan

> Am 23.01.2021 um 11:28 schrieb Bob Bishop <rb at gid.co.uk>:
> 
> Hi,
> 
> FWIW I found that applying -lro didn’t work retrospectively, it had to be done when the interface was first configured. Might apply to other options too.
> 
> --
> Bob Bishop
> rb at gid.co.uk
> 
>> On 22 Jan 2021, at 23:42, Graham Menhennitt <graham at menhennitt.com.au> wrote:
>> 
>> Try "ifconfig $ifname -rxcsum -txcsum" and possibly " -vlanhwtso -tso4" as well.
>> 
>> Graham
>> 
>> On 23/01/2021 8:10 am, Stefan Bethke wrote:
>>> I have a weird situation with an PCEngines APU3, where I can't seem to be able to transmit packets through either of the igb interfaces. With tcpdump, I can see packets arriving, and the interface flags appear to be just fine:
>>>        options=e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
>>>        ether 00:0d:b9:58:xx:xx
>>>        inet6 fe80::20d:b9ff:xxxx:xxxx%igb0 prefixlen 64 scopeid 0x1
>>>        inet6 2a02:8108:4840:xxxx:xxxx:xxxx:xxxx:xxxx prefixlen 64 autoconf
>>>        inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
>>>        media: Ethernet autoselect (1000baseT <full-duplex>)
>>>        status: active
>>>        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
>>> 
>>> dhclient is running on that interfaces, and I got an IPv6 address through RA.
>>> 
>>> Assigning an address manually doesn't change anything.
>>> 
>>> igb0 at pci0:1:0:0:        class=0x020000 card=0x00008086 chip=0x157b8086 rev=0x03 hdr=0x00
>>>    vendor     = 'Intel Corporation'
>>>    device     = 'I210 Gigabit Network Connection'
>>>    class      = network
>>>    subclass   = ethernet
>>> 
>>> # freebsd-version
>>> 12.2-RELEASE
>>> 
>>> I installed 12.2-REL a couple of weeks ago, and haven't done anything since.
>>> 
>>> Tried the three different port with different cables on different switch ports, which are working fine with other machines.
>>> 
>>> I'm installing updates now via a USB adapter.
>>> 
>>> Any suggestions?
>>> 
>>> 
>>> Stefan
>>> 
>>> --
>>> Stefan Bethke <stb at lassitu.de>   Fon +49 151 14070811
>>> 
>> _______________________________________________
>> freebsd-stable at freebsd.org mailing list
>> https://lists.freebsd.org/mailman/listinfo/freebsd-stable
>> To unsubscribe, send any mail to "freebsd-stable-unsubscribe at freebsd.org"
>> 
> 
> _______________________________________________
> freebsd-stable at freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to "freebsd-stable-unsubscribe at freebsd.org"

--
Stefan Bethke <stb at lassitu.de>   Fon +49 151 14070811

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: Message signed with OpenPGP
URL: <http://lists.freebsd.org/pipermail/freebsd-stable/attachments/20210123/afde337b/attachment.sig>