Recent 7-STABLE has stopped booting properly (for me): SCSI over
umass and firewire implicated
Andrew Reilly
andrew-freebsd at areilly.bpc-users.org
Sat Jun 20 08:37:22 UTC 2009
Hi there,
Rather than jumping straight to send-pr, I thought that I'd see
if anyone had experience or thoughts about this.
I've had a couple of external drives on my AMD64-X2 + NVidia
system for some time. The Maxtor 300G Firewire drive died
recently though, and I replaced it with a 1TB WD "MyBook"
firewire+usb2 drive. I also have a WD 750G MyBook that is only
USB2.
OK, I suspect that the 1TB WD drive might be a problem, but the
750G WD drive *used* to come up just fine. I had it work once
on FW, but when I got the run_interrupt_driven_hooks: still
waiting for xpt_config problem, I switched it to usb and that
seemed to make it happy for a while...
Anyway, I did my update-to-stable this morning, and the reboot
did not go smoothly. It stopped at the dreaded:
un_interrupt_driven_hooks: still waiting after 60 seconds for xpt_config
run_interrupt_driven_hooks: still waiting after 120 seconds for xpt_config
and started again after I unplugged both drives.
On another reboot the 750G WD drive didn't probe at all, even
after an unplug-replug exercise, and the 1TB drive grabbed da0,
which the other usually uses. That time, the boot messages
complained (bizarrely):
xptioctl: pass driver is not in the kernel
xptioctl: put "device pass" in your kernel config file
I say bizarrely because I'm running a kernel config that is
only:
include GENERIC
ident DUNCAN
device atapicam
nodevice atapicd # ATAPI CDROM drives
nodevice atapifd # ATAPI floppy drives
nodevice atapist # ATAPI tape drives
so of course device pass is in there...
In summary, the only way that I seem to be able to reliably boot
at the moment is to
* unplug the external drives while the computer is down,
* let it fail to boot while attempting to mount them from the fstab file,
* power them up and plug them in, in the right order,
* and watch that /dev/da0 and then /dev/da1 are created,
* mount them manually,
* then exit the shell to allow the system to finish coming up.
This clearly isn't a recipe that allows for graceful unattended
recovery from power outages or remote system maintenance.
I'll attach my most recent dmesg, which is "verbose", in the
hope that it helps the discussion.
Thanks in advance for any suggestions,
--
Andrew
-------------- next part --------------
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.2-STABLE #65: Sat Jun 20 11:08:34 EST 2009
root at duncan.reilly.home:/usr/obj/usr/src/sys/DUNCAN
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80d6e000.
Preloaded elf obj module "/boot/kernel/geom_mirror.ko" at 0xffffffff80d6e1a8.
Preloaded elf obj module "/boot/kernel/snd_ich.ko" at 0xffffffff80d6e818.
Preloaded elf obj module "/boot/kernel/sound.ko" at 0xffffffff80d6ee00.
Calibrating clock(s) ... i8254 clock: 1193243 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2211342742 Hz
CPU: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ (2211.34-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0x20fb1 Stepping = 1
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x1<SSE3>
AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow!+,3DNow!>
AMD Features2=0x3<LAHF,CMP>
Cores per package: 2
L1 2MB data TLB: 8 entries, fully associative
L1 2MB instruction TLB: 8 entries, fully associative
L1 4KB data TLB: 32 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB unified TLB: 0 entries, disabled/not present
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
usable memory = 3207524352 (3058 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x0000000000d9c000 - 0x00000000ba57ffff, 3112058880 bytes (759780 pages)
avail memory = 3094441984 (2951 MB)
ACPI APIC Table: <Nvidia AWRDACPI>
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
ULE: setup cpu group 0
ULE: setup cpu 0
ULE: adding cpu 0 to group 0: cpus 1 mask 0x1
ULE: setup cpu group 1
ULE: setup cpu 1
ULE: adding cpu 1 to group 1: cpus 1 mask 0x2
ACPI: RSDP @ 0x0xf6d10/0x0014 (v 0 Nvidia)
ACPI: RSDT @ 0x0xbfff3000/0x0030 (v 1 Nvidia AWRDACPI 0x42302E31 AWRD 0x01010101)
ACPI: FACP @ 0x0xbfff3040/0x0074 (v 1 Nvidia AWRDACPI 0x42302E31 AWRD 0x01010101)
ACPI: DSDT @ 0x0xbfff30c0/0x4C3F (v 1 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000C)
ACPI: FACS @ 0x0xbfff0000/0x0040
ACPI: MCFG @ 0x0xbfff7d80/0x003C (v 1 Nvidia AWRDACPI 0x42302E31 AWRD 0x01010101)
ACPI: APIC @ 0x0xbfff7d00/0x007C (v 1 Nvidia AWRDACPI 0x42302E31 AWRD 0x01010101)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 2
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
MADT: Interrupt override: source 14, irq 14
MADT: Interrupt override: source 15, irq 15
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00040010 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00000000 err: 0x00010000 pcm: 0x00010000
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_buffersize=16384 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
wlan_amrr: <AMRR Transmit Rate Control Algorithm>
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
io: <I/O>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (Jun 20 2009 11:06:41)
acpi0: <Nvidia AWRDACPI> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
AcpiOsDerivePciId: \\_SB_.PCI0.VT86.PDEV -> bus 0 dev 1 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.VT86.PIRQ -> bus 0 dev 1 func 0
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, bfef0000 (3) failed
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 5 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 5 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 10 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 5 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 5 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 12 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 12 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link8: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 11 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link9: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link10: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 11 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link11: Index IRQ Rtd Ref IRQs
Initial Probe 0 12 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 12 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link12: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link13: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 10 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link14: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 11 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link15: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 9 10 11 12 14 15
pci_link16: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 16
Validation 0 255 N 0 16
After Disable 0 255 N 0 16
pci_link17: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 17
Validation 0 255 N 0 17
After Disable 0 255 N 0 17
pci_link18: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 18
Validation 0 255 N 0 18
After Disable 0 255 N 0 18
pci_link19: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 19
Validation 0 255 N 0 19
After Disable 0 255 N 0 19
pci_link20: Index IRQ Rtd Ref IRQs
Initial Probe 0 16 N 0 16
Validation 0 16 N 0 16
After Disable 0 255 N 0 16
pci_link21: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link22: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link23: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link24: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link25: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link26: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link27: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link28: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link29: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link30: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
pci_link31: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 20 21 22 23
Validation 0 255 N 0 20 21 22 23
After Disable 0 255 N 0 20 21 22 23
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x10de, dev=0x005e, revid=0xa3
domain=0, bus=0, slot=0, func=0
class=05-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x0050, revid=0xa3
domain=0, bus=0, slot=1, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x0052, revid=0xa2
domain=0, bus=0, slot=1, func=1
class=0c-05-00, hdrtype=0x00, mfdev=1
cmdreg=0x0001, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type I/O Port, range 32, base 0xec00, size 5, enabled
map[20]: type I/O Port, range 32, base 0x1c00, size 6, enabled
map[24]: type I/O Port, range 32, base 0x1c40, size 6, enabled
pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.APCS:0)
pci_link26: Picked IRQ 20 with weight 0
pcib0: slot 1 INTA routed to irq 20 via \\_SB_.PCI0.APCS
found-> vendor=0x10de, dev=0x005a, revid=0xa2
domain=0, bus=0, slot=2, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xf2102000, size 12, enabled
pcib0: matched entry for 0.2.INTA (src \\_SB_.PCI0.APCF:0)
pci_link21: Picked IRQ 21 with weight 0
pcib0: slot 2 INTA routed to irq 21 via \\_SB_.PCI0.APCF
found-> vendor=0x10de, dev=0x005b, revid=0xa3
domain=0, bus=0, slot=2, func=1
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=b, irq=12
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xfeb00000, size 8, enabled
pcib0: matched entry for 0.2.INTB (src \\_SB_.PCI0.APCL:0)
pci_link27: Picked IRQ 22 with weight 0
pcib0: slot 2 INTB routed to irq 22 via \\_SB_.PCI0.APCL
found-> vendor=0x10de, dev=0x0059, revid=0xa2
domain=0, bus=0, slot=4, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x05 (1250 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0xb800, size 8, enabled
map[14]: type I/O Port, range 32, base 0xbc00, size 8, enabled
map[18]: type Memory, range 32, base 0xf2105000, size 12, enabled
pcib0: matched entry for 0.4.INTA (src \\_SB_.PCI0.APCJ:0)
pci_link24: Picked IRQ 23 with weight 0
pcib0: slot 4 INTA routed to irq 23 via \\_SB_.PCI0.APCJ
found-> vendor=0x10de, dev=0x0053, revid=0xf2
domain=0, bus=0, slot=6, func=0
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type I/O Port, range 32, base 0xf000, size 4, enabled
found-> vendor=0x10de, dev=0x0054, revid=0xf3
domain=0, bus=0, slot=7, func=0
class=01-01-85, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type I/O Port, range 32, base 0x9f0, size 3, enabled
map[14]: type I/O Port, range 32, base 0xbf0, size 2, enabled
map[18]: type I/O Port, range 32, base 0x970, size 3, enabled
map[1c]: type I/O Port, range 32, base 0xb70, size 2, enabled
map[20]: type I/O Port, range 32, base 0xd000, size 4, enabled
map[24]: type Memory, range 32, base 0xf2100000, size 12, enabled
pcib0: matched entry for 0.7.INTA (src \\_SB_.PCI0.APSI:0)
pci_link29: Picked IRQ 21 with weight 1
pcib0: slot 7 INTA routed to irq 21 via \\_SB_.PCI0.APSI
found-> vendor=0x10de, dev=0x0055, revid=0xf3
domain=0, bus=0, slot=8, func=0
class=01-01-85, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type I/O Port, range 32, base 0x9e0, size 3, enabled
map[14]: type I/O Port, range 32, base 0xbe0, size 2, enabled
map[18]: type I/O Port, range 32, base 0x960, size 3, enabled
map[1c]: type I/O Port, range 32, base 0xb60, size 2, enabled
map[20]: type I/O Port, range 32, base 0xe400, size 4, enabled
map[24]: type Memory, range 32, base 0xf2101000, size 12, enabled
pcib0: matched entry for 0.8.INTA (src \\_SB_.PCI0.APSJ:0)
pci_link30: Picked IRQ 22 with weight 1
pcib0: slot 8 INTA routed to irq 22 via \\_SB_.PCI0.APSJ
found-> vendor=0x10de, dev=0x005c, revid=0xa2
domain=0, bus=0, slot=9, func=0
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x02 (500 ns)
found-> vendor=0x10de, dev=0x0057, revid=0xa3
domain=0, bus=0, slot=10, func=0
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x01 (250 ns), maxlat=0x14 (5000 ns)
intpin=a, irq=12
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xf2103000, size 12, enabled
map[14]: type I/O Port, range 32, base 0xe800, size 3, enabled
pcib0: matched entry for 0.10.INTA (src \\_SB_.PCI0.APCH:0)
pci_link23: Picked IRQ 23 with weight 1
pcib0: slot 10 INTA routed to irq 23 via \\_SB_.PCI0.APCH
found-> vendor=0x10de, dev=0x005d, revid=0xa3
domain=0, bus=0, slot=11, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
found-> vendor=0x10de, dev=0x005d, revid=0xa3
domain=0, bus=0, slot=12, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
found-> vendor=0x10de, dev=0x005d, revid=0xa3
domain=0, bus=0, slot=13, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
found-> vendor=0x10de, dev=0x005d, revid=0xa3
domain=0, bus=0, slot=14, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
found-> vendor=0x1022, dev=0x1100, revid=0x00
domain=0, bus=0, slot=24, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1101, revid=0x00
domain=0, bus=0, slot=24, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1102, revid=0x00
domain=0, bus=0, slot=24, func=2
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1103, revid=0x00
domain=0, bus=0, slot=24, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0: <memory> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xf2102000-0xf2102fff irq 21 at device 2.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf2102000
ioapic0: routing intpin 21 (PCI IRQ 21) to vector 49
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 10 ports with 10 removable, self powered
ehci0: <NVIDIA nForce4 USB 2.0 controller> mem 0xfeb00000-0xfeb000ff irq 22 at device 2.1 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfeb00000
ioapic0: routing intpin 22 (PCI IRQ 22) to vector 50
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb1: EHCI version 1.0
usb1: companion controller, 4 ports each: usb0
usb1: <NVIDIA nForce4 USB 2.0 controller> on ehci0
usb1: USB revision 2.0
uhub1: <nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb1
uhub1: 10 ports with 10 removable, self powered
pcm0: <nVidia nForce4> port 0xb800-0xb8ff,0xbc00-0xbcff mem 0xf2105000-0xf2105fff irq 23 at device 4.0 on pci0
pcm0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xb800
pcm0: Reserved 0x100 bytes for rid 0x14 type 4 at 0xbc00
ioapic0: routing intpin 23 (PCI IRQ 23) to vector 51
pcm0: [MPSAFE]
pcm0: [ITHREAD]
pcm0: <Avance Logic ALC850 AC97 Codec (id = 0x414c4790)>
pcm0: Codec features 5 bit master volume, no 3D Stereo Enhancement
pcm0: Primary codec extended features double rate PCM, reserved 1, center DAC, surround DAC, LFE DAC, reserved 5
pcm0: ac97 codec dac ready count: 0
pcm0: Mixer "vol":
pcm0: Mixer "pcm":
pcm0: Mixer "speaker":
pcm0: Mixer "line":
pcm0: Mixer "mic":
pcm0: Mixer "cd":
pcm0: Mixer "rec":
pcm0: Mixer "igain":
pcm0: Mixer "ogain":
pcm0: Mixer "line1":
pcm0: Mixer "phin":
pcm0: Mixer "phout":
pcm0: clone manager: deadline=750ms flags=0x8000001e
pcm0: sndbuf_setmap ba408000, 4000; 0xffffff80000b9000 -> ba408000
pcm0: sndbuf_setmap ba40c000, 4000; 0xffffff80000bd000 -> ba40c000
atapci0: <nVidia nForce CK804 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 6.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=60 ostat1=70
ata0: stat0=0x20 err=0x20 lsb=0x20 msb=0x20
ata0: stat1=0x30 err=0x30 lsb=0x30 msb=0x30
ata0: reset tp2 stat0=20 stat1=30 devices=0x0
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 52
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=01
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x04 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 53
ata1: [MPSAFE]
ata1: [ITHREAD]
atapci1: <nVidia nForce CK804 SATA300 controller> port 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xd000-0xd00f mem 0xf2100000-0xf2100fff irq 21 at device 7.0 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xd000
atapci1: [MPSAFE]
atapci1: [ITHREAD]
atapci1: Reserved 0x1000 bytes for rid 0x24 type 3 at 0xf2100000
ata2: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x9f0
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xbf0
ata2: SATA connect time=0ms
ata2: reset tp1 mask=01 ostat0=50 ostat1=00
ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x970
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xb70
ata3: SATA connect time=0ms
ata3: reset tp1 mask=01 ostat0=50 ostat1=00
ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata3: [MPSAFE]
ata3: [ITHREAD]
atapci2: <nVidia nForce CK804 SATA300 controller> port 0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xe400-0xe40f mem 0xf2101000-0xf2101fff irq 22 at device 8.0 on pci0
atapci2: Reserved 0x10 bytes for rid 0x20 type 4 at 0xe400
atapci2: [MPSAFE]
atapci2: [ITHREAD]
atapci2: Reserved 0x1000 bytes for rid 0x24 type 3 at 0xf2101000
ata4: <ATA channel 0> on atapci2
atapci2: Reserved 0x8 bytes for rid 0x10 type 4 at 0x9e0
atapci2: Reserved 0x4 bytes for rid 0x14 type 4 at 0xbe0
ata4: SATA connect status=00000000
ata4: [MPSAFE]
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci2
atapci2: Reserved 0x8 bytes for rid 0x18 type 4 at 0x960
atapci2: Reserved 0x4 bytes for rid 0x1c type 4 at 0xb60
ata5: SATA connect status=00000000
ata5: [MPSAFE]
ata5: [ITHREAD]
pcib1: <ACPI PCI-PCI bridge> at device 9.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xf2000000-0xf20fffff
pcib1: no prefetched decode
pcib1: Subtractively decoded bridge.
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x104c, dev=0x8025, revid=0x01
domain=0, bus=1, slot=10, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xf2004000, size 11, enabled
pcib1: requested memory range 0xf2004000-0xf20047ff: good
map[14]: type Memory, range 32, base 0xf2000000, size 14, enabled
pcib1: requested memory range 0xf2000000-0xf2003fff: good
pcib1: matched entry for 1.10.INTA (src \\_SB_.PCI0.APC3:0)
pci_link18: Picked IRQ 18 with weight 0
pcib1: slot 10 INTA routed to irq 18 via \\_SB_.PCI0.APC3
fwohci0: <Texas Instruments TSB82AA2> mem 0xf2004000-0xf20047ff,0xf2000000-0xf2003fff irq 18 at device 10.0 on pci1
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xf2004000
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 54
fwohci0: [MPSAFE]
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:14:85:56:00:e6:80:b0
fwohci0: invalid speed 7 (fixed to 3).
fwohci0: Phy 1394a available S800, 3 ports.
fwohci0: Link S800, max_rec 4096 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:14:85:e6:80:b0
fwe0: bpf attached
fwe0: Ethernet address: 02:14:85:e6:80:b0
fwip0: <IP over FireWire> on firewire0
fwip0: bpf attached
fwip0: Firewire address: 00:14:85:56:00:e6:80:b0 @ 0xfffe00000000, S800, maxrec 4096
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0xba52c000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
nfe0: <NVIDIA nForce4 CK804 MCP9 Networking Adapter> port 0xe800-0xe807 mem 0xf2103000-0xf2103fff irq 23 at device 10.0 on pci0
nfe0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf2103000
miibus0: <MII bus> on nfe0
ciphy0: <Cicada CS8201 10/100/1000TX PHY> PHY 7 on miibus0
ciphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
nfe0: bpf attached
nfe0: Ethernet address: 00:14:85:e7:78:60
nfe0: [MPSAFE]
nfe0: [FILTER]
pcib2: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pcib2: domain 0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0x9000-0x9fff
pcib2: no prefetched decode
pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.XVR3 - AE_NOT_FOUND
pci2: <ACPI PCI bus> on pcib2
pci2: domain=0, physical bus=2
pcib3: <ACPI PCI-PCI bridge> at device 12.0 on pci0
pcib3: domain 0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0x8000-0x8fff
pcib3: no prefetched decode
pcib3: could not get PCI interrupt routing table for \\_SB_.PCI0.XVR2 - AE_NOT_FOUND
pci3: <ACPI PCI bus> on pcib3
pci3: domain=0, physical bus=3
pcib4: <ACPI PCI-PCI bridge> at device 13.0 on pci0
pcib4: domain 0
pcib4: secondary bus 4
pcib4: subordinate bus 4
pcib4: I/O decode 0x7000-0x7fff
pcib4: no prefetched decode
pcib4: could not get PCI interrupt routing table for \\_SB_.PCI0.XVR1 - AE_NOT_FOUND
pci4: <ACPI PCI bus> on pcib4
pci4: domain=0, physical bus=4
pcib5: <ACPI PCI-PCI bridge> at device 14.0 on pci0
pcib5: domain 0
pcib5: secondary bus 5
pcib5: subordinate bus 5
pcib5: I/O decode 0xa000-0xafff
pcib5: memory decode 0xf0000000-0xf1ffffff
pcib5: prefetched decode 0xe0000000-0xefffffff
pcib5: could not get PCI interrupt routing table for \\_SB_.PCI0.XVR0 - AE_NOT_FOUND
pci5: <ACPI PCI bus> on pcib5
pci5: domain=0, physical bus=5
found-> vendor=0x1002, dev=0x9598, revid=0x00
domain=0, bus=5, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Prefetchable Memory, range 64, base 0xe0000000, size 28, enabled
pcib5: requested memory range 0xe0000000-0xefffffff: good
map[18]: type Memory, range 64, base 0xf1000000, size 16, enabled
pcib5: requested memory range 0xf1000000-0xf100ffff: good
map[20]: type I/O Port, range 32, base 0xa000, size 8, enabled
pcib5: requested I/O range 0xa000-0xa0ff: in range
pcib0: matched entry for 0.14.INTA (src \\_SB_.PCI0.APC3:0)
pcib0: slot 14 INTA routed to irq 18 via \\_SB_.PCI0.APC3
pcib5: slot 0 INTA is routed to irq 18
found-> vendor=0x1002, dev=0xaa20, revid=0x00
domain=0, bus=5, slot=0, func=1
class=04-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 64, base 0xf1010000, size 14, enabled
pcib5: requested memory range 0xf1010000-0xf1013fff: good
pcib0: matched entry for 0.14.INTB (src \\_SB_.PCI0.APC4:0)
pci_link19: Picked IRQ 19 with weight 0
pcib0: slot 14 INTB routed to irq 19 via \\_SB_.PCI0.APC4
pcib5: slot 0 INTB is routed to irq 19
vgapci0: <VGA-compatible display> port 0xa000-0xa0ff mem 0xe0000000-0xefffffff,0xf1000000-0xf100ffff irq 18 at device 0.0 on pci5
pci5: <multimedia, HDA> at device 0.1 (no driver attached)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 55
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: <Generic IRDA-compatible device> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ioapic0: routing intpin 3 (ISA IRQ 3) to vector 56
sio1: [FILTER]
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ioapic0: routing intpin 7 (ISA IRQ 7) to vector 57
ppbus0: [MPSAFE]
ppbus0: [ITHREAD]
plip0: <PLIP network interface> on ppbus0
plip0: WARNING: using obsoleted IFF_NEEDSGIANT flag
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 58
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
powernow0: <Cool`n'Quiet K8> on cpu0
cpu1: <ACPI CPU> on acpi0
powernow1: <Cool`n'Quiet K8> on cpu1
ex_isa_identify()
atkbdc: atkbdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
ahc_isa_probe 0: ioport 0xc00 alloc failed
ahc_isa_probe 1: ioport 0x1c00 alloc failed
ahc_isa_probe 11: ioport 0xbc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
isa_probe_children: probing PnP devices
ums0: <Logitech USB-PS/2 Trackball, class 0/0, rev 1.00/2.10, addr 2> on uhub0
ums0: 2 buttons.
uscanner0: <AGFA SNAPSCAN, class 255/255, rev 1.00/1.00, addr 3> on uhub0
Device configuration finished.
Reducing kern.maxvnodes 196147 -> 100000
procfs registered
lapic: Divisor 2, Frequency 100515587 hz
Timecounter "TSC" frequency 2211342742 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
fwohci0: phy int
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad4: 715403MB <WDC WD7500AACS-00D6B1 01.01A01> at ata2-master SATA150
ad4: 1465147055 sectors [1453518C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
ad4: nVidia check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad6: 715404MB <WDC WD7500AACS-00D6B1 01.01A01> at ata3-master SATA150
ad6: 1465149168 sectors [1453521C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad6
ad6: nVidia check1 failed
ad6: Adaptec check1 failed
GEOM_MIRROR: Device mirror/gm0 launched (2/2).
ad6: LSI (v3) check1 failed
ad6: LSI (v2) check1 failed
ad6: FreeBSD check1 failed
pcm0: measured ac97 link rate at 47997 Hz, will use 48000 Hz
GEOM_LABEL: Label for provider mirror/gm0s1a is ufsid/4a34e7954ade199c.
GEOM_LABEL: Label for provider mirror/gm0s1d is ufsid/4a34e7addf0b3850.
GEOM_LABEL: Label for provider mirror/gm0s1e is ufsid/4a34e79577a524cd.
unknown: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x48 0x00 0x01
(probe0:ata1:0:0:0): error 22
(probe0:ata1:0:0:0): Unretryable Error
(probe0:ata1:0:0:0): Down reving Protocol Version from 2 to 0?
(probe0:ata1:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
(probe0:ata1:0:0:0): CAM Status: SCSI Status Error
(probe0:ata1:0:0:0): SCSI Status: Check Condition
(probe0:ata1:0:0:0): UNIT ATTENTION asc:29,0
(probe0:ata1:0:0:0): Power on, reset, or bus device reset occurred
(probe0:ata1:0:0:0): (probe0:ata1:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
(probe0:ata1:0:0:0): UNIT ATTENTION asc:29,0
(probe0:ata1:0:0:0): Power on, reset, or bus device reset occurred
Retrying Command (per Sense Data)
(probe0:ata1:0:0:0): Retrying Command
(probe0:ata1:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
(probe0:ata1:0:0:0): CAM Status: SCSI Status Error
(probe0:ata1:0:0:0): SCSI Status: Check Condition
(probe0:ata1:0:0:0): NOT READY asc:3a,0
(probe0:ata1:0:0:0): Medium not present
(probe0:ata1:0:0:0): (probe0:ata1:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
(probe0:ata1:0:0:0): NOT READY asc:3a,0
(probe0:ata1:0:0:0): Medium not present
Unretryable error
(probe0:ata1:0:0:0): error 6
(probe0:ata1:0:0:0): Unretryable Error
(probe1:sbp0:0:0:0): error 22
(probe1:sbp0:0:0:0): Unretryable Error
(probe2:sbp0:0:1:0): error 22
(probe2:sbp0:0:1:0): Unretryable Error
(probe3:sbp0:0:2:0): error 22
(probe3:sbp0:0:2:0): Unretryable Error
(probe4:sbp0:0:3:0): error 22
(probe4:sbp0:0:3:0): Unretryable Error
(probe5:sbp0:0:4:0): error 22
(probe5:sbp0:0:4:0): Unretryable Error
(probe6:sbp0:0:5:0): error 22
(probe6:sbp0:0:5:0): Unretryable Error
(probe7:sbp0:0:6:0): error 22
(probe7:sbp0:0:6:0): Unretryable Error
(probe0:ata1:0:0:0): error 6
(probe0:ata1:0:0:0): Unretryable Error
unknown: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x48 0x00 0x01
(probe0:ata1:0:0:0): error 22
(probe0:ata1:0:0:0): Unretryable Error
pass0 at ata1 bus 0 target 0 lun 0
pass0: <PIONEER DVD-RW DVR-110D 1.17> Removable CD-ROM SCSI-0 device
pass0: 3.300MB/s transfers
GEOM: new disk cd0
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00040010 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00000000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 3 to local APIC 1
ioapic0: Assigning ISA IRQ 4 to local APIC 0
ioapic0: Assigning ISA IRQ 7 to local APIC 1
ioapic0: Assigning ISA IRQ 9 to local APIC 0
ioapic0: Assigning ISA IRQ 14 to local APIC 1
ioapic0: Assigning ISA IRQ 15 to local APIC 0
ioapic0: Assigning PCI IRQ 18 to local APIC 1
ioapic0: Assigning PCI IRQ 21 to local APIC 0
ioapic0: Assigning PCI IRQ 22 to local APIC 1
ioapic0: Assigning PCI IRQ 23 to local APIC 0
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
cd0 at ata1 bus 0 target 0 lun 0
cd0: <PIONEER DVD-RW DVR-110D 1.17> Removable CD-ROM SCSI-0 device
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
scsi_cd.c::ioctl cmd=4400648b error=25
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
Trying to mount root from ufs:/dev/mirror/gm0s1a
start_init: trying /sbin/init
GEOM_LABEL: Label ufsid/4a34e7954ade199c removed.
GEOM_LABEL: Label for provider mirror/gm0s1a is ufsid/4a34e7954ade199c.
GEOM_LABEL: Label ufsid/4a34e7addf0b3850 removed.
GEOM_LABEL: Label for provider mirror/gm0s1d is ufsid/4a34e7addf0b3850.
GEOM_LABEL: Label ufsid/4a34e79577a524cd removed.
GEOM_LABEL: Label for provider mirror/gm0s1e is ufsid/4a34e79577a524cd.
GEOM_LABEL: Label ufsid/4a34e7954ade199c removed.
GEOM_LABEL: Label ufsid/4a34e7addf0b3850 removed.
GEOM_LABEL: Label ufsid/4a34e79577a524cd removed.
umass0: <Western Digital External HDD, class 0/0, rev 2.00/1.06, addr 2> on uhub1
umass0:7:0:-1: Attached to scbus7
(probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0?
pass1 at umass-sim0 bus 0 target 0 lun 0
pass1: <WD 7500AAK External 1.06G>E OFMi:x ende wD irdeicstk Adac0ce
ss SCSI-0 device
pass1: 40.000MB/s transfers
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <WD 7500AAK External 1.06> Fixed Direct Access SCSI-0 device
da0: 40.000MB/s transfers
da0: 715404MB (1465149168 512 byte sectors: 255H 63S/T 91201C)
GEOM_LABEL: Label for provider da0s1a is ufsid/484a3a0a61af3002.
GEOM_LABEL: Label ufsid/484a3a0a61af3002 removed.
fwohci0: BUS reset
fwohci0: node_id=0x8800ffc0, gen=2, non CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 0 (me)
firewire0: root node is not cycle master capable
firewire0: bus manager 0 (me)
fwohci0: too many cycle lost, no cycle master presents?
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc1, gen=3, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc1, gen=4, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
firewire0: New S800 device ID:0090a97488ce53aa
(probe0:sbp0:0:0:0): error 22
(probe0:sbp0:0:0:0): Unretryable Error
pass2 at sbp0 bus 0 target 0 lun 0
pass2: <WGDE OMMy: Bonoekw 1d0i2s8k> dFai1x
ed Direct Access SCSI-4 device
pass2: 50.000MB/s transfers
da1 at sbp0 bus 0 target 0 lun 0
da1: <WD My Book 1028> Fixed Direct Access SCSI-4 device
da1: 50.000MB/s transfers
da1: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C)
GEOM_LABEL: Label for provider da1s1a is ufsid/4a324039d6307dd3.
(probe0:sbp0:0:0:1): error 22
(probe0:sbp0:0:0:1): Unretryable Error
ses0 at sbp0 bus 0 target 0 lun 1
ses0: <WD My Book Device > Fixed Enclosure Services SCSI-4 device
ses0: 50.000MB/s transfers
ses0: SCSI-3 SES Device
pass3 at sbp0 bus 0 target 0 lun 1
pass3: <WD My Book Device > Fixed Enclosure Services SCSI-4 device
pass3: 50.000MB/s transfers
GEOM_LABEL: Label ufsid/4a324039d6307dd3 removed.
GEOM_LABEL: Label for provider da0s1a is ufsid/484a3a0a61af3002.
GEOM_LABEL: Label for provider da1s1a is ufsid/4a324039d6307dd3.
GEOM_LABEL: Label for provider mirror/gm0s1e is ufsid/4a34e79577a524cd.
GEOM_LABEL: Label for provider mirror/gm0s1d is ufsid/4a34e7addf0b3850.
GEOM_LABEL: Label ufsid/4a34e7addf0b3850 removed.
GEOM_LABEL: Label ufsid/4a34e79577a524cd removed.
GEOM_LABEL: Label ufsid/4a324039d6307dd3 removed.
GEOM_LABEL: Label ufsid/484a3a0a61af3002 removed.
GEOM_LABEL: Label for provider md0 is ufsid/4a3c9978d1b40db4.
GEOM_LABEL: Label ufsid/4a3c9978d1b40db4 removed.
nfe0: link state changed to UP
fuse4bsd: version 0.3.9-pre1, FUSE ABI 7.8
splash: image decoder found: green_saver
More information about the freebsd-stable
mailing list