Read_dma timeout - FreeBSD 6-1
Ikare
ikare.run at gmail.com
Fri Jan 19 04:43:20 UTC 2007
Hi Clay,
> Sounds like power problem to me. Perhaps there is not enough power for
> the drive.
I tried to unplug all devices (cd-roms, 2nd disk, ...), and it still
appears :-/
> Best advice I could give is not to use Maxtor. They have known problems
> with many models and in my opinion are not good hard drives.
I think I'm okay with that !!!
Here's the result from
smartctl -a -t long /dev/ad4
If someone can find somthing wrong in it ...
Thanks
--
Ivan Kurzweg
Web : http://www.kurzweg.info
BOFH excuse #14: sounds like a Windows problem, try calling Microsoft
support
-------------- next part --------------
smartctl version 5.37 [i386-portbld-freebsd6.1] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax 10 family (SATA/300)
Device Model: Maxtor 6V160E0
Serial Number: V39SA0AG
Firmware Version: VA111900
User Capacity: 160,041,885,696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Fri Jan 19 08:33:31 2007 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 41) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: (1382) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 71) minutes.
SMART Attributes Data Structure revision number: 32
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 214 209 063 Pre-fail Always - 7209
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 46
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 239 239 187 Pre-fail Always - 36113
9 Power_On_Hours 0x0032 253 253 000 Old_age Always - 153
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 117
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 051 044 000 Old_age Always - 825294897
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 041 253 000 Old_age Always - 49
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 726
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 0
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
210 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0
211 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0
212 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 45 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 03 46 00 00 00 a0 00 00:00:48.403 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:00:48.346 SET FEATURES [Set transfer mode]
ec 00 01 01 00 00 a0 00 00:00:48.331 IDENTIFY DEVICE
81 04 10 04 01 32 e0 00 00:00:48.171 [VENDOR SPECIFIC]
c6 00 10 04 01 32 e0 00 00:00:36.693 SET MULTIPLE MODE
Error 1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 46 00 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 00:00:48.346 SET FEATURES [Set transfer mode]
ec 00 01 01 00 00 a0 00 00:00:48.331 IDENTIFY DEVICE
81 04 10 04 01 32 e0 00 00:00:48.171 [VENDOR SPECIFIC]
c6 00 10 04 01 32 e0 00 00:00:36.693 SET MULTIPLE MODE
ef 03 46 00 00 e0 e0 00 00:00:36.692 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately in off-line mode".
Drive command "Execute SMART Extended self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 71 minutes for test to complete.
Test will complete after Fri Jan 19 09:44:31 2007
Use smartctl -X to abort test.
More information about the freebsd-stable
mailing list