umass0: BBB reset failed, TIMEOUT

[O. Hartmann]

Hello.

Got problmes with an external USB 2.0 2,5" harddrive. Short time
readings of the on-HD filesystem (msdosfs), reading 1GB in one piece
works sometimes fine, but reading more 1GB files or accessing the disk
rapidly remains the disk frozen. Kernel reports

umass0: Genesyslogic USB Mass Storage Device, rev 2.00/0.33, addr 2
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <HTS42404 0M9AT00 0811> Fixed Direct Access SCSI-0 device
da0: 40.000MB/s transfers
da0: 38154MB (78140160 512 byte sectors: 255H 63S/T 4864C)
GEOM_LABEL: Label for provider da0s5 is msdosfs/TRANSPORT.

umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT

Unmounting is impossible and remains the box frozen after a while.

Box is a AMD64 system, running a yesterday cvsupdated FreeBSD 6.0-STABLE.
ehci and uhci are enabled in kernel config. System is a ASUS A8N-SLI
Deluxe, dmesg is attached.

I googled for similar problems and found a long list since FreeBSD 5.1.
Is there an incompatibility with some chipsets?

Thanks,
Oliver
-------------- next part --------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 6.0-STABLE #15: Sat Jan  7 16:21:15 CET 2006
    root at thor.schanze.de:/usr/obj/usr/src/sys/THOR
ACPI APIC Table: <Nvidia AWRDACPI>
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 Processor 3500+ (2211.34-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x10ff0  Stepping = 0
  Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  AMD Features=0xe2500800<SYSCALL,NX,MMX+,<b25>,LM,3DNow+,3DNow>
real memory  = 2147418112 (2047 MB)
avail memory = 2064515072 (1968 MB)
ioapic0 <Version 1.1> irqs 0-23 on motherboard
netsmb_dev: loaded
acpi0: <Nvidia AWRDACPI> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
powernow0: <Cool`n'Quiet K8> on cpu0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <memory> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
ichsmb0: <SMBus controller> port 0xe400-0xe41f,0x4c00-0x4c3f,0x4c40-0x4c7f irq 20 at device 1.1 on pci0
ichsmb0: [GIANT-LOCKED]
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus generic I/O> on smbus0
ohci0: <OHCI (generic) USB controller> mem 0xd8104000-0xd8104fff irq 21 at device 2.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 10 ports with 10 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfeb00000-0xfeb000ff irq 22 at device 2.1 on pci0
ehci0: [GIANT-LOCKED]
usb1: EHCI version 1.0
usb1: companion controller, 4 ports each: usb0
usb1: <EHCI (generic) USB 2.0 controller> on ehci0
usb1: USB revision 2.0
uhub1: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 10 ports with 10 removable, self powered
pcm0: <nVidia nForce4> port 0xdc00-0xdcff,0xe000-0xe0ff mem 0xd8103000-0xd8103fff irq 23 at device 4.0 on pci0
pcm0: <Avance Logic ALC850 AC97 Codec>
atapci0: <nVidia nForce4 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 6.0 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <nVidia nForce4 SATA150 controller> port 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xd800-0xd80f mem 0xd8102000-0xd8102fff irq 21 at device 7.0 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
atapci2: <nVidia nForce4 SATA150 controller> port 0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xc400-0xc40f mem 0xd8101000-0xd8101fff irq 22 at device 8.0 on pci0
ata4: <ATA channel 0> on atapci2
ata5: <ATA channel 1> on atapci2
pcib1: <ACPI PCI-PCI bridge> at device 9.0 on pci0
pci5: <ACPI PCI bus> on pcib1
fwohci0: <Texas Instruments TSB43AB22/A> mem 0xd8004000-0xd80047ff,0xd8000000-0xd8003fff irq 16 at device 11.0 on pci5
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:11:d8:00:00:12:53:30
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
nve0: <NVIDIA nForce MCP9 Networking Adapter> port 0xb000-0xb007 mem 0xd8100000-0xd8100fff irq 23 at device 10.0 on pci0
nve0: Ethernet address 00:11:d8:92:a3:15
miibus0: <MII bus> on nve0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
nve0: Ethernet address: 00:11:d8:92:a3:15
pcib2: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci4: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 12.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 13.0 on pci0
pci2: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 14.0 on pci0
pci1: <ACPI PCI bus> on pcib5
pci1: <display, VGA> at device 0.0 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <8 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0 at vga0
Timecounter "TSC" frequency 2211343497 Hz quality 800
Timecounters tick every 1.200 msec
Fast IPsec: Initialized Security Association Processing.
acd0: DVDR <NEC DVD RW ND-3500AG/2.19> at ata0-master UDMA33
ad8: 190782MB <SAMSUNG SP2004C VM100-31> at ata4-master SATA150
ad10: 194481MB <Maxtor 6B200M0 BANC1B70> at ata5-master SATA150
ar0: 381564MB <nVidia MediaShield RAID0 (stripe 64 KB)> status: READY
ar0: disk0 READY using ad8 at ata4-master
ar0: disk1 READY using ad10 at ata5-master
cd0 at ata0 bus 0 target 0 lun 0
cd0: <_NEC DVD_RW ND-3500AG 2.19> Removable CD-ROM SCSI-0 device 
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
GEOM_LABEL: Label for provider ar0s3h is ufs/CRYPTO.
GEOM_LABEL: Label for provider ar0s4d is ufs/SCRATCH.
Trying to mount root from ufs:/dev/ar0s1a
umass0: Genesyslogic USB Mass Storage Device, rev 2.00/0.33, addr 2
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <HTS42404 0M9AT00 0811> Fixed Direct Access SCSI-0 device 
da0: 40.000MB/s transfers
da0: 38154MB (78140160 512 byte sectors: 255H 63S/T 4864C)
GEOM_LABEL: Label for provider da0s5 is msdosfs/TRANSPORT.
g_vfs_done():acd0[READ(offset=32768, length=2048)]error = 5
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT
umass0: BBB reset failed, TIMEOUT
umass0: BBB bulk-in clear stall failed, TIMEOUT
umass0: BBB bulk-out clear stall failed, TIMEOUT