How to diagnose crashes - N440GX + 4.11-STABLE

[Larry Gadallah]

Hello all:

I have an Intel N440GX running 4.11-STABLE that is crashing every few
hours. I built a kernel with debugging enabled, but it doesn't seem to
help, or at least I haven't been able to take advantage of it. I'm
wondering if there's a way I can figure out if this is a hardware or a
kernel compatibility issue? The dmesg output is below:

Thanks in advance,

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.11-STABLE #4: Mon Jun  6 20:59:29 PDT 2005
    larry at pinawa.gadallah.com:/usr/src/sys/compile/PINAWA
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (548.63-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x673  Stepping = 3
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 536805376 (524224K bytes)
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> q
avail memory = 518447104 (506296K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard: 1 CPUs
 cpu0 (BSP): apic id:  0, version: 0x00040011, at 0xfee00000
 io0 (APIC): apic id:  1, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc03c6000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03c609c.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 8 entries at 0xc00fdf40
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard
pci0: <PCI bus> on pcib0
dc0: <82c169 PNIC 10/100BaseTX> port 0x1400-0x14ff mem
0xfa103000-0xfa1030ff irq 10 at device 11.0 on pci0
dc0: Ethernet address: 00:a0:cc:53:0f:2b
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sym0: <875> port 0x1800-0x18ff mem
0xfa100000-0xfa100fff,0xfa103400-0xfa1034ff irq 5 at device 13.0 on
pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x2000-0x20ff mem
0xfa101000-0xfa101fff,0xfa103800-0xfa1038ff irq 11 at device 13.1 on
pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
fxp0: <Intel 82558 Pro/100 Ethernet> port 0x1060-0x107f mem
0xfa000000-0xfa0fffff,0xfa104000-0xfa104fff irq 11 at device 15.0 on
pci0
fxp0: Ethernet address 00:d0:b7:88:8f:14
inphy0: <i82555 10/100 media interface> on miibus1
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <Intel 82371AB PCI to ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device
18.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 18.2 irq 11
Timecounter "PIIX"  frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0x1040-0x104f
at device 18.3 on pci0
pci0: <Cirrus Logic GD5480 SVGA controller> at 20.0
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcc7ff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
acd0: CD-RW <SONY CD-RW CRX175E> at ata1-slave PIO4
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at sym0 bus 0 target 4 lun 0
da0: <FUJITSU MAN3184MP 0108> Fixed Direct Access SCSI-3 device
da0: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing Enabled
da0: 17522MB (35885448 512 byte sectors: 255H 63S/T 2233C)
da1 at sym0 bus 0 target 5 lun 0
da1: <FUJITSU MAN3184MP 0108> Fixed Direct Access SCSI-3 device
da1: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing Enabled
da1: 17522MB (35885448 512 byte sectors: 255H 63S/T 2233C)

-- 
Larry Gadallah,
lgadallah AT gmail DOT com