FreeBSD6.0-STABLE got wicked up since today's cvsupdate (Xorg/X11, USB)

[O. Hartmann]

Hello.
I did today (21st December) the last cvsupdate (did yesterday cvsupdate
before) with a lot of new entries in /etc/rc.d.
Since then I ran into massif problems with X11. I use the lastes Xorg
stuff from the ports, only for your information.

Problem: After kernel came up, booting into multiuser mode, starting X11
I lost USB keyboard and mouse. Changing USB keyboard against PS/2 one
results also in a completely stuck keyboard.
Booting machine in singleuser mode with PS/2 keyboard, disabling xdm and
Xserver and starting machine then without this stuff with console
results in a working system. Enabling then xdm and the approriate entry
in Xservers also results in a working, as usual, environment.

maybe something got wicked up with the last cvsupdate?

Attached you'll find the last dmesg.

Bos is a DELL Optiplex 270, operating system is FreeBSD 6.0-STABLE.
moused is enabled, also devd (as you can see). Box worked with the same
config since the last cvsupdate today.

I deleted all /etc/rc.d entries and replaced them via mergemaster -i
with the newest stuff! What else could cause this problem?

Thanks in advance,
Oliver
-------------- next part --------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 6.0-STABLE #18: Wed Dec 21 16:35:52 UTC 2005
    root at edda.physik.uni-mainz.de:/usr/obj/usr/src/sys/EDDA
ACPI APIC Table: <DELL   GX270  >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 2.60GHz (2593.52-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4400<CNTX-ID,<b14>>
  Hyperthreading: 2 logical CPUs
real memory  = 527892480 (503 MB)
avail memory = 506970112 (483 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
netsmb_dev: loaded
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL GX270  > on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
p4tcc1: <CPU Frequency Thermal Control> on cpu1
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
drmsub0: <Intel i865G GMCH> port 0xed98-0xed9f mem 0xe8000000-0xefffffff,0xfeb80000-0xfebfffff irq 16 at device 2.0 on pci0
error: [drm:pid0:drm_load] *ERROR* Card isn't AGP, or couldn't initialize AGP.
device_attach: drmsub0 attach returned 12
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xff80-0xff9f irq 16 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xff60-0xff7f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xff20-0xff3f irq 16 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xffa80800-0xffa80bff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
em0: <Intel(R) PRO/1000 Network Connection Version - 3.2.18> port 0xdf40-0xdf7f mem 0xfeae0000-0xfeafffff irq 18 at device 12.0 on pci1
em0: Ethernet address: 00:0b:db:7e:96:43
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf mem 0xfeb7fc00-0xfeb7ffff irq 18 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH5 SATA150 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfea0-0xfeaf irq 18 at device 31.2 on pci0
atapci1: failed to enable memory mapping!
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
ichsmb0: <Intel 82801EB (ICH5) SMBus controller> port 0xeda0-0xedbf irq 17 at device 31.3 on pci0
ichsmb0: [GIANT-LOCKED]
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus generic I/O> on smbus0
pcm0: <Intel ICH5 (82801EB)> port 0xee00-0xeeff,0xedc0-0xedff mem 0xfeb7fa00-0xfeb7fbff,0xfeb7f900-0xfeb7f9ff irq 17 at device 31.5 on pci0
pcm0: [GIANT-LOCKED]
pcm0: <Analog Devices AD1981B AC97 Codec>
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xca7ff,0xca800-0xcbfff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <8 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0 at vga0
ums0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
ukbd0: Gemplus Dell USB Smartcard Keyboard, rev 1.10/1.00, addr 2, iclass 3/1
kbd1 at ukbd0
Timecounters tick every 1.200 msec
ad0: 38166MB <WDC WD400EB-75CPF0 06.04G06> at ata0-master UDMA100
acd0: CDRW <HL-DT-ST CD-RW/DVD-ROM GCC-4480B/C104> at ata1-master UDMA33
SMP: AP CPU #1 Launched!
cd0 at ata1 bus 0 target 0 lun 0
cd0: <HL-DT-ST RW/DVD GCC-4480B C104> Removable CD-ROM SCSI-0 device 
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/ad0s1a