USB2 device
Michael E. Mercer
mmercer at nc.rr.com
Mon Mar 29 20:10:15 PST 2004
Julian,
It works if I plug it directly into a usb port on my PC. But it does not
get seen if I plug it into a SIIG SlimHub 2.0.
Any ideas?
Michael
On Mon, 2004-03-29 at 19:17, Julian Elischer wrote:
> here's mine:
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights
> reserved.
> FreeBSD 4.8-RELEASE-p15 #13: Mon Mar 29 13:34:08 PST 2004
>
> root at teraserver.dev.vicor-nb.com:/usr/obj/usr/prod/system/VERS_4_8_BRANCH/src/sys/VICOR
> Timecounter "i8254" frequency 1193182 Hz
> Timecounter "TSC" frequency 2800107696 Hz
> CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2800.11-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0xf25 Stepping = 5
>
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Hyperthreading: 2 logical CPUs
> real memory = 1073659904 (1048496K bytes)
> avail memory = 1040945152 (1016548K bytes)
> Preloaded elf kernel "k2" at 0xc0456000.
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> Using $PIR table, 12 entries at 0xc00f23c0
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> pcib1: <PCI to PCI bridge (vendor=8086 device=2561)> at device 1.0 on
> pci0
> pci1: <PCI bus> on pcib1
> uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xd800-0xd81f
> irq 5 at device 29.0 on pci0
> usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uscanner0: Hewlett-Packard HP ScanJet 6200C, rev 1.00/1.00, addr 2
> uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xd400-0xd41f
> irq 9 at device 29.1 on pci0
> usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
> usb1: USB revision 1.0
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xd000-0xd01f
> irq 9 at device 29.2 on pci0
> usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
> usb2: USB revision 1.0
> uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7000000-0xf70003ff irq
> 11 at device 29.7 on pci0
> ehci_pci_attach: companion usb0
> ehci_pci_attach: companion usb1
> ehci_pci_attach: companion usb2
> usb3: EHCI version 1.0
> usb3: companion controllers, 2 ports each: usb0 usb1 usb2
> usb3: <EHCI (generic) USB 2.0 controller> on ehci0
> usb3: USB revision 2.0
> uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub3: 6 ports with 6 removable, self powered
> pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on
> pci0
> pci2: <PCI bus> on pcib2
> bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xf6800000-0xf6801fff irq 10
> at device 5.0 on pci2
> bfe0: Ethernet address: 00:0e:a6:18:a4:72
> miibus0: <MII bus> on bfe0
> ukphy0: <Generic IEEE 802.3u media interface> on miibus0
> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> pci2: <ATI Mach64-GR graphics accelerator> at 9.0 irq 9
> ahc0: <Adaptec 2940A Ultra SCSI adapter> port 0xb400-0xb4ff mem
> 0xf4000000-0xf4000fff irq 9 at device 10.0 on pci2
> aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
> pcm0: <Creative CT5880-E> port 0xb000-0xb03f irq 10 at device 12.0 on
> pci2
> pcm0: <unknown ac97 codec> (id=0x454d4328)
> fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xa800-0xa83f mem
> 0xf3000000-0xf301ffff,0xf3800000-0xf3800fff irq 9 at device 13.0 on pci2
> fxp0: Ethernet address 00:02:b3:ea:e7:d6
> inphy0: <i82555 10/100 media interface> on miibus1
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> isab0: <PCI to ISA bridge (vendor=8086 device=24c0)> at device 31.0 on
> pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH4 ATA100 controller> port
> 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0-0x7 irq 9 at device 31.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> pcm1: <Intel 82801DB (ICH4)> port 0x9400-0x943f,0x9800-0x98ff mem
> 0xf2000000-0xf20000ff,0xf2800000-0xf28001ff irq 9 at device 31.5 on pci0
> pcm1: <unknown ac97 codec> (id=0x41445370)
> orm0: <Option ROMs> at iomem
> 0xc0000-0xc7fff,0xc8000-0xc87ff,0xcc000-0xcd7ff on isa0
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
> isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model Generic PS/2 mouse, device ID 0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x100>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A, console
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> ppc0: <Parallel port> at port 0x378-0x37f on isa0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/16 bytes threshold
> lpt0: <Printer> on ppbus0
> lpt0: Polled port
> IP packet filtering initialized, divert enabled, rule-based forwarding
> enabled, default to accept, logging disabled
> IPsec: Initialized Security Association Processing.
> ad0: 117246MB <Maxtor 6Y120L0> [238216/16/63] at ata0-master UDMA100
> Waiting 4 seconds for SCSI devices to settle
> uscanner0: at uhub0 port 2 (addr 2) disconnected
> uscanner0: detached
> uscanner0: Hewlett-Packard HP ScanJet 6200C, rev 1.00/1.00, addr 2
> Mounting root from ufs:/dev/ad0s1a
> umass0: LEXAR MEDIA JUMPDRIVE PRO, rev 2.00/0.00, addr 2
> da0 at umass-sim0 bus 0 target 0 lun 0
> da0: <LEXAR JUMPDRIVE PRO 0> Removable Direct Access SCSI-2 device
> da0: 650KB/s transfers
> da0: 246MB (503808 512 byte sectors: 64H 32S/T 246C)
> (da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not supported, increasing
> minimum_cmd_size to 10.
>
>
> jtest# usbdevs -v
> Controller /dev/usb0:
> addr 1: low speed, self powered, config 1, UHCI root hub(0x0000),
> Intel(0x0000), rev 1.00
> port 1 powered
> port 2 addr 2: low speed, self powered, config 1, HP ScanJet
> 6200C(0x0201), Hewlett-Packard(0x03f0), rev 1.00
> Controller /dev/usb1:
> addr 1: low speed, self powered, config 1, UHCI root hub(0x0000),
> Intel(0x0000), rev 1.00
> port 1 powered
> port 2 powered
> Controller /dev/usb2:
> addr 1: low speed, self powered, config 1, UHCI root hub(0x0000),
> Intel(0x0000), rev 1.00
> port 1 powered
> port 2 powered
> Controller /dev/usb3:
> addr 1: low speed, self powered, config 1, EHCI root hub(0x0000),
> (0x8086)(0x0000), rev 1.00
> port 1 powered
> port 2 powered
> port 3 powered
> port 4 powered
> port 5 powered
> port 6 addr 2: low speed, power 200 mA, config 1, JUMPDRIVE
> PRO(0x0200), LEXAR MEDIA(0x05dc), rev 0.00
> jtest#
> jtest# dd if=/dev/da0 of=/dev/null bs=64k
> Mar 29 19:01:32 jtest /k2: (da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not
> supported, increasing minimum_cmd_size to 10.
> Mar 29 19:01:32 jtest /k2: (da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not
> supported, increasing minimum_cmd_size to 10.
> 3936+0 records in
> 3936+0 records out
> 257949696 bytes transferred in 47.199914 secs (5465046 bytes/sec)
> jtest#
> jtest# cat VICOR
> machine i386
> cpu I586_CPU
> cpu I686_CPU
> ident VICOR
> maxusers 256
>
> makeoptions DEBUG=-g
>
> options INET #InterNETworking
> options FFS #Berkeley Fast Filesystem
> options FFS_ROOT #FFS usable as root device [keep
> this!]
> options SOFTUPDATES #Enable FFS soft updates support
> options UFS_DIRHASH #Faster in large dirs (memory
> tradeoff)
> options MFS #Memory Filesystem
> options NFS #Network Filesystem
> options MSDOSFS #MSDOS Filesystem
> options CD9660 #ISO 9660 Filesystem
> options PROCFS #Process filesystem
> options COMPAT_43 #Compatible with BSD 4.3 [KEEP
> THIS!]
> options SCSI_DELAY=4000 #Delay (in ms) before probing SCSI
> options UCONSOLE #Allow users to grab the console
> options USERCONFIG #boot -c editor
> options SYSVSHM #SYSV-style shared memory
> options SYSVMSG #SYSV-style message queues
> options SYSVSEM #SYSV-style semaphores
> options P1003_1B #Posix P1003_1B real-time
> extensions
> options _KPOSIX_PRIORITY_SCHEDULING
> options KBD_INSTALL_CDEV # install a CDEV entry in /dev
> options INCLUDE_CONFIG_FILE # Include this file in kernel
> options DDB
> #options DDB_UNATTENDED
> options KTRACE #kernel tracing
> options IPDIVERT #Divert sockets
> options IPSEC #IP security
> options IPSEC_ESP #IP security (crypto; define w/
> IPSEC)
> options IPFIREWALL #Packet firewall
> options IPFIREWALL_DEFAULT_TO_ACCEPT #Only block on firewall
> machines
> options IPFIREWALL_FORWARD
> options MAXDSIZ=(2047*1024*1024)
>
> #options SMP # Symmetric MultiProcessor
> Kernel
> #options APIC_IO # Symmetric (APIC) I/O
> #options HTT # HyperThreading Technology
>
> device isa
> device pci
>
> device fdc0 at isa? port IO_FD1 irq 6 drq 2
> device fd0 at fdc0 drive 0
>
> device ata0 at isa? port IO_WD1 irq 14
> device ata1 at isa? port IO_WD2 irq 15
> device ata
> device atadisk # ATA disk drives
> device atapicd # ATAPI CDROM drives
> options ATA_STATIC_ID #Static device numbering
>
> device ahc # AHA2940 and onboard AIC7xxx devices
> device dpt # DPT Smartcache - See LINT for
> options!
> device mlx
> device mly
> device twe
>
> device scbus # SCSI bus (required)
> device da # Direct Access (disks)
> device sa # Sequential Access (tape etc)
> device cd # CD
> device pass # Passthrough dev (direct SCSI
> access)
> device pt
> device ch
> device ses
>
> device atkbdc0 at isa? port IO_KBD
> device atkbd0 at atkbdc? irq 1 flags 0x1
> device psm0 at atkbdc? irq 12
>
> device vga0 at isa?
>
> pseudo-device splash
>
> device sc0 at isa? flags 0x100
>
> device npx0 at nexus? port IO_NPX irq 13
>
> device sio0 at isa? port IO_COM1 flags 0x10 irq 4
> device sio1 at isa? port IO_COM2 irq 3
>
> device ppc0 at isa?
> device ppbus
> device lpt
>
> device em # Intel PRO/1000 adapter Gigabit
> Ethernet Card (``Wiseman'')
> device miibus
> device bfe # Broadcom BCM440x
> device bge # Broadcom BCM570x (``Tigon
> III'')
> device fxp
>
> device pcm
>
> device xdcp
> device cy0
> #options CY_PCI_FASTINTR # Use with cy_pci unless irq is
> shared
>
> pseudo-device loop # Network loopback
> pseudo-device ether # Ethernet support
> pseudo-device pty # Pseudo-ttys (telnet etc)
> pseudo-device md # Memory "disks"
> pseudo-device bpf #Berkeley packet filter
> pseudo-device vn
> pseudo-device gif #IPv6 and IPv4 tunneling
> pseudo-device speaker
>
> # USB support
> device ehci # EHCI PCI->USB interface
> device uhci # UHCI PCI->USB interface
> device ohci # OHCI PCI->USB interface
> device usb # USB Bus (required)
> device ugen # Generic
> device uhid # "Human Interface Devices"
> #device ukbd # Keyboard
> device ulpt # Printer
> device umass # Disks/Mass storage - Requires
> scbus and da
> device ums # Mouse
> device uscanner # Scanners
>
> device firewire # Generic
> device fwe # Generic
> device sbp # Generic
>
> jtest#
>
> ignore the xdcp entry... it's local.
>
> I don;t see any mention of cam or SCSI in your config..
> umass requires cam asn they implement SCSI-over-USB
> to get the disk function.
>
> This is not however perfect.. I get hangs on boot if the drive is
> already inserted, and sometimes it doesn't notice that it is removed...
>
> but it does give me 5.4MBytes/sec which is > than teh theoretical
> maximum of about 1.5MB/sec for USB1.1
>
> julian
>
>
> _______________________________________________
> freebsd-stable at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to "freebsd-stable-unsubscribe at freebsd.org"
More information about the freebsd-stable
mailing list